Motherwell Products MWL-180 Harley Cross Bones Luggage Rack Installation Guide

: August 31, 2024
: Motherwell Products

Table of Contents

MWL-180 Harley Cross Bones Luggage Rack
Specifications:
Product Usage Instructions:
Use and Care:
Mounting Procedure:
- FAQ:
Q: Can I carry more than 10 lbs on the rack?
Q: What tools are required for installation?

MWL-180 Harley Cross Bones Luggage Rack

“`html

Specifications:

Product: Motherwell Products Solo Luggage Rack
Models: MWL-180, MWL-180B, MWL-180GB
Fitment: 2016-UP Dyna Low Rider S
Max Capacity: 10 lbs
Technical Specs: May require fender/seat nut kit
MWL-2000-16

Product Usage Instructions:

Use and Care:

Wash your accessories with the same care you use when washing
your motorcycle. Use mild soap and water. Avoid abrasive chemicals
and cleaners. We recommend using non-abrasive automobile wax to
polish chrome products for maintaining appearance and
longevity.

Mounting Procedure:

Install foam on the back of the rack and two round foams at the
front of the rack.
Place the rack on the fender mounting points. (The forward
mount sits on top of the driver’s seat)
Install the stock screw into the rear pick-up point on the rack
(do not tighten).
For the front mount, place the nylon washer on the rack with
the stainless steel on top.
Insert the supplied Phillips screw loosely and then proceed to
tighten both screws down.

FAQ:

Q: Can I carry more than 10 lbs on the rack?

A: No, it is recommended to never carry more than 10 lbs on the
rack to avoid affecting handling. Always secure cargo properly.

Q: What tools are required for installation?

A: You will need a #2 Phillips Screw Driver for installing the
Motherwell Products Solo Luggage Rack.

“`

INSTALLATION INSTRUCTIONS

DOC#M219

MWL-180, MWL-180B, MWL-180GB
FITMENT: 2016-UP Dyna Low Rider S
MAX CAPACITY: 10 lbs
MATERIAL: 3/8″ Solid steel centers & ½” tubing
TECHNICAL SPECS: May require fender/seat nut kit #MWL-2000-16

WELCOME: These instructions describe the procedure for properly installing the Motherwell Products Solo Luggage Rack.
ATTENTION INSTALLER (if other than owner): Please forward this instruction sheet to the purchaser of this product as it contains valuable information necessary to the end user.
CAUTION: Start screw carefully to avoid cross threading.

USE AND CARE: Wash your accessories with the same care you use when washing your motorcycle. Use mild soap and water. DO NOT use abrasive chemicals, cleaners. We recommend the use of non-abrasive automobile wax to polish our chrome products. This will best maintain the appearance of the product and increase longevity.
WARNING: Never carry more than 10 lbs. on rack, and always secure cargo properly. Failure to do so can affect handling. Make sure neither cargo straps are loose nor come in contact with moving parts, i.e., wheels, brakes, etc….

TOOLS REQUIRED: #2 Phillips Screw Driver
PARTS INCLUDED: MWL Part # Luggage Rack MWL-219 2 Phillips ¾” Pan Head Screw FAS-009 2 ¼ Bond Seal S/S FAS-057 1 Foam Tab (Back) FOAM-AFT 2 Round foam tab FOAM-ROUND

MOUNTING PROCEDURE:

Install foam on back of the rack and two round foam at front of rack. 2) Place rack on fender mounting points. (The forward mount sits on top of the driver’s seat) 3) Install the stock screw in to rear pick up point on the rack. (DO NOT TIGHTEN) 4) For the front mount, place the nylon washer on the rack with the stainless steel on top. 5) From there insert the supplied Phillips screw loosely. 6) Proceed to tighten both screws down.

Great Rides Start With Motherwell
Motherwell Products USA, Inc 7074 Portal Way #140 Ferndale, WA 98248 Toll Free 877-703-7118
www.motherwellproducts.com