Motherwell Products MWL-218 Solo Luggage Rack Installation Guide
- August 31, 2024
- Motherwell Products
Table of Contents
Motherwell Products MWL-218 Solo Luggage Rack
Specifications:
- Model: MWL-218, MWL-218B, MWL-218GB
- Fitment: Dyna Low Rider S 2016-UP
- Max Capacity: 10 lbs
- Material: 3/8 Solid steel
- Technical Specs: May require a seat/fender mounting kit #MWL-2000-16
Product Usage Instructions
Use and Care:
Wash your accessories with the same care you use when washing your motorcycle. Use mild soap and water. DO NOT use abrasive chemicals or cleaners. We recommend the use of non-abrasive automobile wax to polish our chrome products for best maintenance and longevity.
Mounting Procedure:
- Install foam on the back of the rack.
- Place the rack on the fender mounting points. (The forward mount sits on top of the driver’s seat)
- Install the stock screw into the rear pick-up point on the rack without tightening it.
- For the front mount, place the nylon washer on the rack with the stainless steel on top.
- Insert the supplied Phillips screw loosely into the front mount.
- Tighten both screws down securely.
FAQ
- Q: What should I do if my cargo exceeds the maximum capacity of 10 lbs?
- A: Never carry more than 10 lbs on the rack as it can affect handling. Always secure cargo properly to avoid any issues.
- Q: Where can I find more information or support for Motherwell Products?
- A: For more information or support, you can contact Motherwell Products USA, Inc at Toll-Free 877-703-7118 or visit their website at www.motherwellproducts.com
Specification
MWL-218, MWL-218B, MWL-218GB
- FITMENT:
- Dyna Low Rider S 2016-UP
- MAX CAPACITY: 10 lbs
- MATERIAL: 3/8” Solid steel
- TECHNICAL SPECS: May require a seat/fender
- mounting kit #MWL-2000-16
Product Information
WELCOME: These instructions describe the procedure for properly installing the
Motherwell Products Solo Luggage Rack.
ATTENTION INSTALLER (if other than the owner): Please forward this instruction
sheet to the purchaser of this product as it contains valuable information
necessary to the end user.
CAUTION: Start screw carefully to avoid cross-threading.
USE AND CARE
Wash your accessories with the same care you use when washing your motorcycle.
Use mild soap and water. DO NOT use abrasive chemicals, cleaners. We recommend
the use of non-abrasive automobile wax to polish our chrome products. This
will best maintain the appearance of the product and increase longevity.
WARNING: Never carry more than 10 lbs. on rack, and always secure cargo
properly. Failure to do so can affect handling. Make sure neither cargo straps
are loose nor come in contact with moving parts, e., wheels, brakes, etc.…
TOOLS REQUIRED
-
2 Phillips Screw Driver
- Kit #3
PARTS INCLUDED
PARTS INCLUDED: MWL Part # 2 Phillips
- ¾” Pan Machine Screw
- FAS-009 2 nylon washers
- FAS-003 2 stainless steel washers FAS-005 1 foam tabs
- FOAM-FWD 1 foam tabs FOAM-AFT
MOUNTING PROCEDURE
- Install foam on back of the rack.
- Place rack on fender mounting points. (The forward mount sits on top of the driver’s seat)
- Install the stock screw in to rear pick up point on the rack. (DO NOT TIGHTEN)
- For the front mount, place the nylon washer on the rack with the stainless steel on top.
- From there insert the supplied Phillips screw loosely.
- Proceed to tighten both screws down.
Contact
- Great Rides Start With Motherwell
- Motherwell Products USA, Inc
- 7074 Portal Way #140
- Ferndale, WA 98248
- Toll Free 877-703-7118
- www.motherwellproducts.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>