naturewater 64425,64426 4 Stage Reverse Osmosis Water Instruction Manual
- August 29, 2024
- Naturewater
Table of Contents
- naturewater 64425,64426 4 Stage Reverse Osmosis Water
- Specifications
- Product Usage Instructions
- FAQ
- Introduction
- System functionality
- Required tools and parts
- Pressure tank
- Wastewater clamp assembly
- Operation and maintenance
- Technical data
- Troubleshooting
- CONTACT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
naturewater 64425,64426 4 Stage Reverse Osmosis Water
Specifications
- Product: 4-stage Reverse Osmosis Water System
- Models: 64425, 64426
Product Usage Instructions
Safety Precautions
- Before using the device, carefully read and understand the operation instructions provided in the manual. Keep the operation instructions in a safe place for future reference.
System Functionality
- The system components include various filters, a booster pump, a pressure tank, and a faucet. The water flow involves different stages from feed water to purified water and wastewater.
Required Tools and Parts
- Tools and parts required for installation and maintenance include a knife, electric drill, Teflon tape, hammer, wrench, scissors, faucet, tank, feed water valve, water line, clamp, tank valve, faucet bracket, and reverse osmosis membrane.
Installing the Feed Water Valve
- To install the feed water valve, connect the T-piece to the water source ensuring that the water supply comes from the cold water line.
FAQ
- Q: Where can I find the most recent version of the manual in various languages?
- A: The most recent version of the manual can be found on our online shop at: https://www.wiltec.de/docsearch
- Q : What safety precautions should I take when using this product?
- A: Please read and follow the safety instructions provided in the manual to minimize the risk of injury while using the device.
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury
we urge that our clients take some basic safety precautions when using this
device. Please read the operation instruc-tions carefully and make sure you
have understood its content.
Keep these operation instructions safe
Safety instructions
- This device is intended to operate and function according to the instructions in this manual. It is not designed to work outside the listed specifications, and any attempt to do so or tamper with the device may result in damage to the device and/or personal injury.
- This device is not a toy; keep it out of reach of small children. If the device needs maintenance or repair, please contact your local service technician.
- Ensure the feed water temperature is above 4 ℃. Water temperatures below 4 ℃ can cause ice formation and damage the device.
- Before connecting the device, make sure the power source is correct. Incorrect voltage can cause damage to the device and/or a fire hazard.
- Do not damage the device or use it if the power cord is damaged. A damaged power cord can cause electric shock or fire. If the power cord is damaged, unplug it immediately and do not use the device.
- Read all instructions before starting the installation and operation of the system. Follow all steps precisely to avoid damage to the system or improper operation.
- This system contains filters that need to be replaced at certain intervals. The replacement intervals vary depending on usage; please contact your local dealer.
- Install the system with potable water only, as the system will not function properly with non-potable water sources and may require additional pre-treatment.
- Ensure that the source water pressure is within the recommended range. If the source water pressure exceeds the maximum pressure of 7 bar, a pressure-reducing valve may be required.
- Ensure that the source water temperature is between 5 ℃ and 45 ℃. The system will not func-tion properly if these temperatures are exceeded.
- Do not install the system on a hot water source.
- Do not use the system for noticeably contaminated water such as raw sewage or well water.
- This device must not be disassembled, opened, or altered. Tampering with the device can lead to malfunction or damage and will void the warranty.
- Do not cover the device, as this will prevent proper heat dissipation and can lead to damage or fire.
- Do not place any objects on the device, as this can cause damage and leaks.
- Adhere to all recommended operating pressures and temperatures; otherwise, the device will be damaged. Avoid contact with corrosive materials.
- Keep away from heat sources.
System functionality
№| Name| №| Name
1| Feed Water| 7| Faucet
2| PP Sediment Filter| 8| Pressure Tank
3| Activated Carbon Block Filter| 9| Drain
4| Booster Pump| 10| Purified Water
5| Reverse Osmosis Membrane| 11| Wastewater
6| Inline Activated Carbon Block Filter| |
System components
Water flow
№
| Name|
№
| Name
---|---|---|---
Fig. 1| Fig. 2| Fig. 1| Fig. 2
1| T-piece| 9| Automatic flush valve| Check valve
2| Feed water valve| 10| Check valve| Hochdruckschalter
3| PP sediment filter| 11| High-Pressure Switch| Tank valve
4| Low pressure switch| 12| Tank valve| Pressure tank
5| Inlet solenoid valve| Activated carbon block filter| 13|
Pressure tank| Inline-activated carbon block filter
6| Activated carbon block filter| Booster pump| 14| Inline-
activated carbon block filter| Faucet
7| Booster pump| Automatic shut-off valve| 15| Faucet
8| Reverse osmosis membrane| |
No-power water flow
Placement of units
- This device is designed to be installed under the sink or on the countertop. However, if due to space constraints or other limitations, you need to place this device in a suitable location, please ensure that it is accessible and convenient.
- When choosing the installation location, make sure that the cold water line, drain pipe, and power outlet are easily accessible and that there is enough space for filter replacement.
Required tools and parts
- Knife
- Electric drill
- Teflon tape
- Hammer
- Wrench
- Scissors
- Faucet
- Tank
- Feed water valve
- Instructions for use
- Water line
- Clamp
- Tank valve
- Faucet bracket
- Reverse osmosis membrane
- T-piece
- Wastewater clamp
Quick connector
Pressure tank
- Keep the pressure tank within a 3-meter radius of the faucet.
- If longer hoses are needed, use only ¼″ hoses to avoid pressure drop.
- The tank can weigh up to 13.5 kg (30 lbs) when full; place it on a firm and level surface.
- Install the ball valve by screwing it onto the tank and sealing it with Teflon tape to prevent leaks.
- Connect the yellow hose from the post-filter to the pressure tank.
- Apply Teflon tape to the fitting on top of the tank.
- Install the tank valve and tighten it hand-tight.
- Connect the yellow hoses from the system.
- Ensure the valve is open.
Tank ball valve
Feed water valve and T-piece
- Install the T-piece and feed water valve as shown in the diagram.
- Wrap the threads of the feed water valve and T-piece with Teflon tape.
- Connect the white feed water hose from the device to the feed water valve.
Installing the feed water valve
- Install the T-piece of the feed water valve and connect it to the water source.
- Caution! The water supply to your device must come from the cold water line!
- Note! Use only cold, local water as feed water. Hot water will damage your device. Softened feed water extends the lifespan of the reverse osmosis membrane
Installing the wastewater clamp
- Place the wastewater clamp on the drain pipe above the siphon and tighten it securely.
- Using the wastewater clamp as a guide, drill a 6 mm hole that is large enough to pass the ¼″ tubing through one side of the drain pipe. Do not drill through both sides.
- Connect the red wastewater hose from the device to the wastewater clamp.
Wastewater clamp assembly
Installing the faucet
- Select a suitable location near your sink for the faucet.
- Drill a 12-mm diameter hole in the countertop.
- Attach washers, plates, gaskets, and nuts in the order shown in the diagram, and tighten them securely on the countertop.
- Attach the blue purified water hose to the bottom of the faucet and connect the hose to the device.
Operation and maintenance
LED display and control panel
- When powered on, the light illuminates brightly, the buzzer sounds once, the screen flashes once, and the system starts operating. During the automatic flush, which lasts 60 s, the washing symbol (Washing) blinks.
- The device is in water production mode when the water production symbol (Source) is displayed. Once the pressure tank is full, the water production symbol turns off, and the full tank symbol (Full) lights up.
- In case of water shortage or insufficient water pressure, the water shortage symbol (Lack) lights up and the buzzer sounds 10 times.
- The machine produces water for a total of 2 hours. During this period, no flushing occurs. After 2 hours, the machine automatically flushes for 30 s.
- The machine stops automatically after 6 hours of water production or if a water leak is detected. Alarm message: The check symbol blinks, and a buzzer sounds.
Filter replacement reminder
- 1st and 2nd filters: after 270 hours – 3rd filter: after 1620 hours – 4th filter: after 540 hours
- Increased water consumption or exhausted filters trigger an alarm, and the corresponding sym-bol blinks.
- After replacing the filter, press the reset button to reset the filter recognition
Resetting the filters
- Press the reset button for less than 3 s to activate the filter selection.
- Press the reset button again to select the filter you want to reset.
- The symbol for the selected filter blinks.
- Hold the reset button for over 3 s to reset the selected filter.
- After 3 s, a beep confirms the successful reset.
Flush button
- Pressing the flush button: the buzzer sounds once.
- Pressing the flush button during flushing stops the flush program.
- Pressing the flush button during water production or when the water tank is full, flushes the reverse osmosis membrane for 120 s.
Prefilter flushing (initial setup)
- Disconnect the inlet pipe of the reverse osmosis element.
- Open the main water valve and the inlet valve, allowing water to run through the prefilters.
- Dispose of the water that exits during flushing.
- Continue flushing until the water is clear.
- Reconnect the inlet pipe.
Caution! The pump and membrane can be damaged if the prefilters are not flushed.
Pressure tank flushing
- Allow the device to operate and fill the pressure tank.
- The tank takes about 3.5 hours to fill.
- Empty the tank by leaving the faucet open.
- Once the tank is empty, close the faucet and allow the tank to refill.
Regular operation
- The device automatically starts water treatment when the faucet is opened.
- It shuts off automatically when the faucet is closed.
- After use, the device automatically flushes if equipped with an automatic flush function
Filter maintenance
Regular maintenance is required to ensure optimal performance. The frequency
of maintenance depends on the quality of the feed water
- PP filter and block carbon filter: every 3–6 months
- Inline carbon filter: every 6–12 months
- Reverse osmosis membrane: every 18–24 months
For extended periods of non-use, disconnect the device from the power supply. If the device has not been used for a long time, follow the same flushing procedure as during the initial setup.Filter replacement
Filter replacement
- Close the feed water valve.
- Close the ball valve on the pressure tank.
- Open the faucet and drain the remaining water.
- Turn the old cartridge clockwise to remove it.
- Align the new cartridge and gently insert it into the hole.
- Turn it counterclockwise to secure the new cartridge.
- Flush the prefilters after replacement
Technical data
Troubleshooting
Disposal regulations
- EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were imple-mented in the law related to electrical and electronic equipment and appliances.
- All WilTec electric devices that fall under the WEEE regulations are labeled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed of with domestic waste.
- The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE-registration number DE45283704
Disposal of used electrical and electronic appliances (intended for use in the countries of the European Union and other European countries with a separate collection system for these appliances). The logo on the article or on its packaging points out that this article must not be treated as normal household waste but must be disposed to a recycling collec-tion point for electronic and electrical waste equipment. By contributing to the correct disposal of this article you protect the environment and the health of your fellow men. Environment and health are threatened by inappropriate disposal.
Material recycling helps reduce the consumption of raw materials. Additional information on recycling this article can be provided by your local community, municipal waste disposal facilities, or the store where you purchased the article.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH
CONTACT
- Address:
- WilTec Wildanger Technik GmbH
- Königsbenden 12 / 28
- D-52249 Eschweiler
- https://www.naturewater.eu
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>