Shenzhen Lingchuangxun Technology LCX-ZJ1200 WiFi Repeater User Manual
- June 6, 2024
- Shenzhen Lingchuangxun Technology
Table of Contents
Shenzhen Lingchuangxun Technology LCX-ZJ1200 WiFi Repeater
Working condition
|
System LED
| The system LED will stay on after power© on for 3 seconds.30 seconds late
ystem LED will flash slowly and the machine will work normally.
---|---|---
|
Internet LED
| When the machine is in Repeater or AP mode and the Internet connection is
correct.
The Internet LED is on,otherwise it is off.
|
Extension LED
| A.The LED is green,indicating that the signal between the repeater and the
router is full.
B. The LED is yellow,indicating that the ( signal between the repeater and the
router is normal.
C. The LED is red,indicating that the signal between the repeater and the
router is poor.
|
Extension LED
| When network cable is connecting,the will flash quickly,otherwise it will
be off.
|
Reset button
| Press and hold the reset key for 8 seconds,the system will be resat.
WPS button
| Short press, the red LED flashes quiclldy. The red light will be on for 2
seconds when match successfully,and the machine will restart automatically.
The red light will be offfor2 seconds when matching is unsuccessful or
overtime, and the machine will restart automatically loo.
Working mode Diagram
Repeater Mode: As a wireless signal extender
A. Extend your Wi-Fi signal without using any cables to reduce wiring
troubles.
B. Extend your Wi-Fi signal with a cable, connect your device and
extender stably.
AP Mode: As a wired signal extender (access point)
Get better WiFi speed by connecting the router and the extender with network
cable in the poor WiFi signal area.
Quick Installation Guide
When the machine work normally,use the mobile phone to search and connect to WiFi 2.4G pro_X>OOOOCorWiFi 5G pro_xxxxxx, (xxxxxx is the last 6 numbers of the repeater MAC address)
Note: If the mobile phone does not automatically jump to setting page after
connecting,please click “forget” the wifi name that has been connected on the
mobile in witi manage,turn off the wifi and then reopen the wifi to search
it,or input” 192.168.11.1 “.
Wi-Fi Repeater mode setup
Step1: Click repeater mode to enter the network search page.
Step2: Select the wireless signal you want to expand,ifit is a hidden network, you need to add it manually.
Step3: Enter your router connection password and click 11NEXT11 •
If you don’t want the same name as your router,please choose and input the
new name.
Step4: Click the “Finish” button to complete the relay mode configuration
(The extended WiFi’s password is the same as the routers 1 by default).
Step5: Complete Repeater Mode setting.
AP mode Setting
Step1: Click to Select “AP” mode to enter the setting page
Step2: Set the wireless name and password with more than 8 digits(the wireless name and password can be set according to personal preference).
Step3: Click the “Finish” button to complete the AP mode configuration.
Step4: Complete AP mode setting.
FAQ ( Frequently Asked Questions )
Q1: What should I do if the mobile phone is connected to the extender
SSID,but it does not automatically jump to the login interface?
A1: If the mobile phone is connected to the extender 88ID,but it does not Jump
to login intertace; you can open the mobile browser and enter “192.168.11. 1”
to enter.
A2: Reset the extender(plug ln the extender and wait for the system llght to
flash,press the reset button to restore the factory settings)
Q2: After the relay mode extension is set successfully1what should I do if
the extension signal is connected but there is no network?
A1 :Please check whether the network light is on for a long time; lf lt ls
not,please check whether the router can go onllne normally
A2: Reset the extender(plug in the extender and walt for the sysem light to
flash,press the reset button to restore factory settings)
A3: Power off the router and restart it.
Q3: After the relay mode extension is set successfully1what should I do if
the extension lights and network lights are not on?
A 1: In this case,the connection password of the upper-level router is
Incorrectly entered.Reset the extender and reset the extension.
Q4: The signal connected to the extender is good,but the Internet speed is
slow,what should I do?
A1: Check the status of the extension light,if lt is red,please move the
position of the repeater unUI the extension light is green.
A2: Restart the router and reset the extender
A3:The extender only ampllfies the signal of the orlginal router to extend the
coverage distance;it will not increase the netvvork speed on the basis of
theoriginal network speed
Q5: What should I do if the network speed is only half of the original
when the repeater is connected?
A1: If the repeater uses a single frequency band for receiving and
transmitting; this means that the bandwidth of the repeater is actually dMded
into two halves,half is used to reveive signals from the upper-level
router,and half is used to transmit wlreless signals for users Use,resultlng
in the speed of the Internet halved. The solution is to use the 2.4G signal
for reveiving and connecting with the upper·level router,and the user
connection uses a 5G slgnal;or you can use the 5G signal for receMng and
connection with the upper-level router,and the user connection uses a 2.4G
signal.In this way, the bandwidth of the amplifier can be used to the greatest
extent and the actual network speed can be avoided.
Q6: What should I do if I want to reset the extension name and password?
A1: Please reset the extender and reset it.When the system button ls slow
flashing,the reset is successful!
The equipment complies with FCC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.