naturewater NW-3-50ROLT Reverse Osmosis 3 Stage System Instruction Manual
- May 15, 2024
- Naturewater
Table of Contents
- Introduction
- Safety Instructions
- Other instructions
- Product and accessories
- Installation instructions
- Quick fitting
- Installing the diverter valve
- Instructions for first use
- Technical data
- Functional schematic diagram
- Troubleshooting
- Disposal regulations
- CUSTOMER SUPPORT
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
naturewater NW-3-50ROLT Reverse Osmosis 3 Stage System
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical
data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities,
please contact us.
Introduction
Thank you for purchasing this quality product. To minimise the risk of injury
we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions carefully and make sure you
have understood its content.
Keep these operation instructions safe.
Safety Instructions
- Clean, flush and replace filter cartridges regularly.
- Do not disassemble parts indiscriminately as this may cause leaks or damage.
- Do not use a power supply with an inappropriate voltage rating.
- Disconnect the mains plug and turn off the water tap before storing the machine for an extended period of time.
- Do not store or use the machine at an ambient temperature of 0 ℃ or below.
- Take care when installing or removing the cartridge or moving the machine.
Other instructions
-
When not in use, turn off the water supply and close the ball valve to prevent damage from water hammer. Uncontrolled water hammer can cause leaks and damage to the filter housing.
We accept no liability for damage caused by water hammer. -
In the event of a problem, disconnect the appliance from the power and water supply and contact a specialist. Replacing the filters may solve the problem.
-
The machine will vibrate slightly during the filtration process.
-
It is recommended to have the cartridges replaced by a specialist.
Caution!
Water hammer is a shock or pressure wave that occurs when flowing water is
suddenly forced to stop or change direction. If the occupants of a building
suddenly close a valve, a pressure wave will spread through the building’s
pipes.
Product and accessories
№ | Name |
---|---|
1 | Filter system |
2 | Three filter cartridges consisting of : Combi filter: PP and activated |
carbon block filter, reverse osmosis membrane and T33 inline activated carbon
block filter
3| Accessory box consisting of : Faucet, three-way valve, three hoses,
instructions, and adapter
№ | Name | № | Name |
---|---|---|---|
1 | Water faucet | 4 | User’s manual |
2 | 3-way valve | 5 | Adaptor |
3 | 3 PE hoses (1,5 m, ¼″, red, blue, and white) | **** | **** |
Note: might vary depending on disposability.
Installation instructions
Note on cutting the tube
Quick fitting
-
Install the water pipe
-
Pull out the water pipe
№ | Description | № | Description |
---|---|---|---|
1 | Insert water pipe. | 4 | Release the lock by pressing it. |
2 | Insert clamp. | 5 | Pull out the water pipe. |
3 | Pull out the clamp. | **** | **** |
Installing the diverter valve
-
Close the feed water valve.
-
Wrap sealing tape around the thread of the diverter valve.
-
Connect the diverter valve to the feed water valve and the hose (Fig. 1)
-
Insert the ¼″ pipe into the diverter valve (fig. 2).
-
Open the feed water valve and the tap to check that the connection is leaktight.
№ | Name | № | Name |
---|---|---|---|
1 | Hose | 5 | O-ring |
2 | O-ring | 6 | Feed water valve |
3 | Sealing tape | 7 | ¼″ pipe |
4 | Diverter valve | 8 | ¼″ pipe |
Nr. | Name | ||
--- | --- | ||
1 | Combi filter indicator | ||
2 | RO membrane indicator | ||
3 | T33 activated carbon block filter indicator | ||
4 | Low water indicator | ||
5 | Filter reset button | ||
6 | Select button |
Instructions for first use
- Connect the reverse osmosis system to the adapter. The buzzer sounds three times, then all LED indicators start flashing and the appliance is flushed for 90 s.
- Automatic rinsing: After 2 hours of operation, the appliance is automatically rinsed for 10 s.
- Manual rinse: Press both the selection button and the reset button for 2 s. The appliance switches to rinse mode and rinses for 90 s.
Replacing the filter cartridges
Reminder function for cartridge replacement
The corresponding LED lights up when 20 % of the service life remains. The
buzzer sounds 3 times when the appliance is producing water.
When the service life has expired, the buzzer sounds 5 times when the
appliance is producing water.
Resetting the cartridge
- Press and hold the selection button for 2 s to enter filter reset mode. The LED indicator for the combi filter lights up and the other LED indicators are off.
- Press the selection button to select the cartridge to be replaced. When the corresponding indicator lights up, press the reset button.
- After resetting, the selection mode is automatically cancelled if no operation is performed.
Replacing the cartridges and maintaining the device
Recommended replacement intervals for cartridges
Stages | Filter cartridges | Service life (guide value) (months) |
---|---|---|
1 st stage | PP and activated carbon block filter (PCB) | **** 3–6 |
2 nd stage | **** RO membrane | **** 12 |
3 rd stage | **** T33 inline activated carbon block filter | **** 3–6 |
Note!
- The actual service life of filters can be influenced by areas, water quality, seasons and daily water consumption, so the period for filter replacement may vary.
- Please replace the cartridges regularly.
Cartridge Replacement Steps
Step 1
Step 2
Step 3
Step 4
Technical data
Feed water quality | Municipal tap water |
---|---|
Working pressure (bar) | 5–7 |
Water inlet pressure (bar) | 1–4 |
Suitable temperature (℃) | 5–38 |
Humidity (%) | ≤90 |
Water flow rate ( ℓ ⁄min) | 0.13 |
Working pressure (bar) | 5–7 |
Process chart of the water treatment process
№ | Name | № | Name |
---|---|---|---|
1 | Feed water | 5 | Reverse-osmosis membrane |
2 | PP and activated carbon block filter (PCB) | 6 | Special Booster pump |
3 | Filtered water (optional | 7 | Faucet |
4 | Inline activated carbon block filter (T33) |
Functional schematic diagram
№ | Name/description | № | Name/description |
---|---|---|---|
1 | Filtered water (optional) | 6 | 3-way ball valve |
2 | Pure water pipe | 7 | Adapter |
3 | Tap water pipe | 8 | Power supply |
4 | Drain water pipe | 9 | Assemble the filters in clockwise rotation. |
5 | Inlet pipe |
Troubleshooting
Problem | Possible cause | Proposed solution |
---|---|---|
Water pump out of order, system not working | Insufficient feed water pressure |
Raise feed water pressure.
No electricity or outage| Switch on.
High-pressure switch damaged| Exchange high-pressure switch.
Pump blocked, adapter fuse blown| Replace adapter, repair water pump.
Water pump is running, but system is not working| Reverse-osmosis membrane
obstructed| Replace reverse-osmosis membrane.
Pressure loss of water pump| Repair water pump.
Solenoid valve for flushing damaged| Replace flush solenoid valve
The water drain does not stop when the machine is in standby mode| Inlet water
solenoid valve damaged| Replace feed water solenoid valve.
Cannot stop working when the faucet is off or repeated starting| High pressure
switch damaged| Repair or replace high pressure switch.
Check valve damaged| Replace check valve.
Leakage| Quick fitting leaks| Check leakage reason and change the
corresponding parts.
Filter leaks
Filter cap leaks
No water output| Quick fitting clogged| Replace parts one by one to check the
cause of the clog.
Filter clogged
Filter cap clogged
Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were implemented in the law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.
The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE registration number DE45283704.
Disposal of
used electrical and electronic appliances (intended for use in the countries
of the European Union and other European countries with a separate collection
system for these appliances).
The logo on the article or on its packaging points out that this article must
not be treated as normal household waste but must be disposed to a recycling
collection point for electronic and electrical waste equipment.
By contributing to the correct disposal of this article you protect the
environment and the health of your fellow men. Environment and health are
threatened by inappropriate disposal.
Material recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal waste disposal facilities, or the store where you purchased the article.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in
part, of this instruction manual require the written permission of WilTec
Wildanger Technik GmbH.
CUSTOMER SUPPORT
The information contained in this document may alter at any time without
previous notice. It is prohibited to copy or spread any parts of this document
in any way without prior written allowance. All rights reserved.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible
mistakes in this operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible
efforts to ensure that the operating manual is complete, faultless, and up to
date, mistakes cannot be entirely avoided. If you should find a mistake or
wish to make a suggestion for improvement, we look forward to hearing from
you.
Send an e-mail to:
service@wiltec.info
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in
our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
To return orders for exchange, repair, or other purposes, please use the
following address. Attention!
To allow for a smooth execution of your complaint or return, it is important
to contact our customer service team before returning the goods.
Returns Department WilTec Wildanger Technik GmbH Königsbenden 28 52249
Eschweiler
E-mail: service@wiltec.info
Tel: +49 2403 55592–0
Fax: +49 2403 55592–15
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
https://www.naturewater.eu
Item 64406–64408
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>