naturewater NW-3-PPCTOUF Water Filter Instruction Manual

naturewater NW-3-PPCTOUF Water Filter

Specifications

• Product: Nature water NW-3-PPCTOUF water filter

• Model Numbers: 64422, 64423

• Filter Stages:

  • Filter Stage 1: PP sediment filter
  • Filter Stage 2: Activated carbon granulate filter (GAC)
  • Filter Stage 3: Activated carbon block filter (CTO) –
    Ultrafilter water filter (UF)

• Website: https://www.naturewater.eu

Product Usage Instructions

Safety Instructions

Before using the water filter, read and follow all operating instructions and safety information provided in the manual to ensure safe usage.

Filter Functions

• PP Sediment Filter: Removes larger suspended
  particles from the water.

• Activated Carbon Filters:

  • CTO Activated Carbon Filter: Effectively removes chlorine, binds colour and odours, and filters impurities.
  • Granular Activated Carbon Filter (GAC): Filters smallest impurities to extend reverse osmosis membrane life.

Cartridge Replacement

1. Close the feed-water valve.
2. Open the faucet and drain any residual water from the system.
3. Turn the old cartridge clockwise and remove it from the cap.
4. Align the new cartridge with the central cap and press it lightly into the opening.
5. Tighten the new cartridge anti-clockwise and open the valves.
6. Perform a pre-filter rinse after changing the filter.

FAQ

• Where can I find the most recent version of the user manual?
• You can find the latest version of the user manual in various languages on the online shop via the following link: https://www.wiltec.de/docsearch.
• How often should I replace the filter cartridges?
• It is recommended to replace the filter cartridges as per the guidelines provided in the manual or based on the specific usage and water quality in your area.

Read and follow the operating instructions and safety information before using it for the first time.
Technical changes reserved!
Due to further developments,
illustrations, functioning steps, and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

Introduction

The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights are reserved.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual or in the diagrams and figures shown.
Even though WilTec Wildanger Technik GmbH has undergone the biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date , mistakes cannot be entirely If you make a mistake or wish to suggest improvement, we look forward to hearing from you.

Send an email to:

• [email protected]
• or use our contact form:
• https://www.wiltec.de/contacts/
• The most recent version of this manual in various languages can be found in our online shop via:
• https://www.wiltec.de/docsearch

Our postal address is:

• WilTec Wildanger Technik GmbH
• Königsbenden 12
• 52249 Eschweiler
• Germany

To return orders for exchange, repair, or other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods.

Returns Department

• WilTec Wildanger Technik GmbH
• Königsbenden 28
• 52249 Eschweiler
• Email: [email protected]
• Tel: +49
• 2403 5559 2 0
• Fax: +49 2403 5559 2 1 5

Thank you for purchasing this quality product.
To minimise the risk of injury we urge that our clients take some basic safety precautions when using this device. Please read the operation instructions carefully and make sure you have understood its content. Keep these operation instructions safe.

Safety instructions

• This appliance is intended for use and operation by the instructions in this manual. It is not intended for operation outside the stated specifications and any attempt to do so or to tamper with the appliance may result in damage to the appliance and/or personal injury.
• This appliance is not a toy and must be kept out of the reach of small children.
• If the appliance requires maintenance or repair, please contact a service technician.
• Ensure that the temperature of the feed water is above 4 ℃. If the water temperature is below 4 ℃, ice may form and damage the
• This system contains filters that must be replaced at certain intervals. The replacement intervals vary depending on use.
• Please only install the system with drinking water. With non-potable water sources, the system will not function properly and additional pre-treatment may be required.
• Ensure that the water pressure is approx. 4 bar. If the source water pressure exceeds the minimum pressure, a pressure-reducing valve may be required.
• Ensure that the temperature of the source water is between 5 ℃ and 45 ℃. The system will not function properly if these temperatures are exceeded. Do not install on a hot water source.
• Do not use the system for noticeably contaminated water such as raw sewage or well water.
• The appliance must not be dismantled, opened or modified. Tampering with the appliance can lead to malfunctions or damage and will invalidate the warranty.
• Do not cover the appliance, as this impedes heat dissipation and can lead to damage or fire.
• Do not place any objects on the appliance, as this may damage the appliance and cause leaks.
• Observe all recommended values for operating pressures and temperatures, otherwise, the appliance may be damaged.
• Avoid contact with corrosive materials.
• Protect from heat.

Filters and filter stages

carbon block filter (CTO)
64423| PP sediment filter| Activated carbon block filter (CTO)-| Ultrafilter water filter (UF)

Filter functions

odours and also filters the smallest impurities from the water to extend the service life of the reverse osmosis membrane.
Granular activated carbon filter (GAC)
Ultrafilter water filter (UF)| Removes suspended particles, turbidity, bacteria and other harmful substances with a filtration performance of up to 0.01 µ

Cartridge replacement

No Name

1. Untighten

2. Tighten

3. Close the feed water valve

4. Open the faucet and drain any residual water from the system

5. Turn the old cartridge clockwise and then remove it from the cap.

6. Align the new cartridge with the central cap and press it lightly into the opening

7. Tighten the new cartridge anti-clockwise and open the valves.

8. Carry out a pre filter rinse after changing the filter.

Technical data

Flow chart of the water treatment process
64422

No Name

1. Water inlet valve
2. T-piece
3. PP sediment filter
4. Activated carbon granulate filter
5. Activated carbon block filter
6. Faucet

64423

No Name

1. Water inlet valve
2. T-piece
3. PP sediment filter
4. Activated carbon block filter
5. Ultra water filter
6. Faucet

Positioning the device

• This device is designed to be placed under a sink or on a countertop. However, if there is not enough space or for other reasons, it can be installed in another suitable location.
• When choosing the location, make sure that the cold water pipe, drain pipe and socket are easily accessible and that there is enough space to change the filter.

Installing the feed water valve

• The feed water connection should be as close as possible to the water filters in the series.
• Install the T piece of the feed water valve and then connect it to the water source.

Caution! The water supply to your appliance must be via the cold water pipe. Hot water can damage your appliance. Softened feed water extends the service life of the filter cartridges.

Installing the faucet

1. Choose a suitable place for the faucet near the sink.
2. Drill a hole with a diameter of 1 2 mm in the worktop.
3. Fit the washers, plates, gaskets and nuts in the sequence shown in the illustration and screw them to the worktop.
4. Attach the clean water hose to the underside of the faucet and connect it to the appliance.
5. Install the faucet at the desired location as shown in the illustration. Either on the left or right side, depending on the faucet.

Maintenance

Regular maintenance is required to ensure optimum operation of the appliance. The frequency of maintenance depends on the quality of the feed water and the extent to which the system is used. Below are some guidelines for scheduled filter changes, although the frequency of filter changes may vary. If in doubt, contact a service technician.

• Change PP sediment filters every 3-6 months or as required
• Replace bayonet filters every 1 8 2 4 months or as required
• Replace carbon block filter every 6 1 2 months or as required
• Change the activated carbon granulate filter every 6 1 2 months or as required

Disconnect the appliance from the power supply if you will not be using it for a longer time or if you will be absent. If the appliance has been switched off and has not been used for a long time, carry out the same rinsing process as when it was first switched on

Troubleshooting

Important notice

The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction manual require the written permission of WilTec Wildanger Technik GmbH.

CONTACT

• https://www.naturewater.eu
• Item 64422, 64423

References

• naturewater - eine Marke der WilTec Wildanger Technik GmbH

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>