Cleverio SD310 Wireless Doorbell kit User Guide
- August 27, 2024
- Cleverio
Table of Contents
Wireless Doorbell kit
SD310
User guide
Item: 66285
Use
Push button
Open the back of the push button using a screwdriver (1). Push the bracket
downwards to separate it from the push button (2).
Remove the plastic separator from the battery compartment on the back of the
push button. To replace a depleted battery, open the battery compartment and
insert 1x CR2032 battery, mind the polarity. Close the battery compartment.
Note! It’s important that the new battery does not touch the top of the battery compartment during installation as this can short circuit the push button.
Chime
-
Open the battery compartment on the back of the chime.
Insert the batteries (3x AA-batteries, not incl.) into the chime mind the polarity. -
The chime emits a sound to indicate it’s ready for pairing.
-
Press the push button within 2 minutes of installing the bat-teries into the chime to pair the units together. The chime emits a sound to confirm the pairing was successful.
To pair multiple chimes to the same button, repeat the steps above.
To pair multiple buttons to the same chime, remove the batteries from the
chime each time you pair a new button. If the chime does not emit a sound
during stage 2, press any button on the chime when the batteries are
disconnected to remove any residual battery power, wait a short moment, and
attempt to pair again.
Note! A chime can be paired to multiple push buttons, as each chime
supports up to 8 memory slots. If an additional push button is paired after
this, the earliest paired button is automatically disconnected.
A push button can control up to 50 chimes total.
The chime emits a sound to indicate when the battery power is low. The chime
does not need to be re-paired again after replacing the batteries.
Chime settings
a. Press the button on the front of the chime to enable/ disable sound and/or
the flashing light when the push button is pressed in the following order:
flash, sound, flash + sound.
b. Press multiple times to set the volume.
c. Press mulitple times to change the preferred melody (36 melodies).
Mounting the push button bracket
The push button bracket can be mounted to a surface using the included double-
sided adhesive tape or screws and plugs (not included). The adhesive tape is
recommended for a smooth surface that is protected from weather. Screws and
plugs are recommended
for outdoor mounting.
Double-sided adhesive tape
Peel off both protective sides on the tape and attach it to the bracket. Press
the bracket and tape onto the surface.
Press (1) and slide (2) the push button onto the bracket until you hear a
click to mount it. Screws and plugs (not included)
Drill two holes into the mounting surface using an electric drill. Insert
plastic plugs into the hole and attach the bracket using the screws.
Press (1) and slide (2) the push button onto the bracket until you hear a
click to mount it. Detaching the push button
If you need to remove the push button from a mounted position you can detach
it from the bracket using a screwdriver.
Resetting
Press and hold the melody selection button (c) on the chime for 20 seconds
until a sound is emitted to remove the pairing between the chime and button.
Troubleshooting
I’m having trouble pairing the chime to the push button.
Make sure the push button and chime has enough battery power.
Make sure the push button and chime are not too far apart (up to 100 m) and
have no obstacles in the signal path. Place the chime close to the push button
and try again.
Avoid installing the push button on a metal door frame.
Re-initiate the pairing procedure, make sure to follow the instructions in the
same order they are described in the manual. Make sure to follow the notes for
battery insertion to avoid damaging and short circuiting the push button.
Safety information
The chime is intended for use in temperatures from 0-35 °C and not for outdoor
use. Only for use in dry areas. The push button can be mounted outdoors, but
we recommend you to mount it in a place where it’s shielded from wind and
rain.
Do not open or modify the devices in any way, this should only be carried out
by a qualified technician .
The range of 100 meters can vary due to concrete walls, electrical or electro-
magnetic sources that can interfere with the signal.
Keep the batteries away and out of reach from children. A swallowed battery
can result in severe injuries and a deadly outcome. Immediately consult a
doctor if you suspect that a battery has been swallowed or entered the body
inany other way.
Simplified EU Declaration of Conformity
Kjell & Company hereby declares that this device is in compliance with the
essential requirements and other relevant provisions of Directive 2014/53/EU.
Full text of the EU declaration of conformity is available at
www.kjell.com/66285
Specifications
| Frequency: | 433.92 MHz |
|---|---|
| Power: | 1x CR2032 battery (included) |
3x AA batteries (sold separately)
Range:| Up to 100 meters
Size:| Push button: 83x33x17 mm
Chime: 90x90x43 mm
Included:| Push button (transmitter), chime (receiver), 1x CR2032 battery,
bracket, adhesive tape, manual
Wireless frequency:| 433.050–434.790 MHz
Effective Radiated Power:| <20 mW
www.cleverio.se
Box 50435 Malmö
Sweden
2024-07-16
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>