Tenveo M5BEX Speakerphone User Manual

August 27, 2024
Tenveo

M5BEX Speakerphone
User Manual
VersionV1.1

Packing List

Tenveo M5BEX Speakerphone - Parts

Charging

You can check the battery level from the OLED. When battery is lower than 20%, the OLED battery turns red to indicate low power along with warning tone every 3 minutes, please charge it in time to avoid affecting the use.
Plug the device into a USB power source. The device lasts for up to 27 hours of talk time and takes approximately 3 hours (PD charging, 5V/8000mA) to fully сharge.

Tenveo M5BEX Speakerphone - Charging

Button Function

Tenveo M5BEX Speakerphone - Button Function

Button Status Function OLED
Speaker mute ON/OFF Speaker mute (only for USB device)
Volume down Decrease volume
Volume up Increase volume
Microphone mute ON/OFF microphone mute
Answer/Hang up Answer/ Hang up when calling
(only for Bluetooth device)
Bluetooth Turn ON/OFF Bluetooth function
(only for Bluetooth device)
ON/OFF/MUTE/UNMUTE ON/OFF(Long press)
MUTE/UNMUTE(Shot press)

LED Indicator Function

Tenveo M5BEX Speakerphone - Indicator Function

Bluetooth status indicator
(only for Bluetooth device)| Blue light flashing| Bluetooth is pairing
---|---|---
Green light on| Bluetooth connected
Microphone status indicator| Red light on| Microphone mute
Green light on| Microphone working normally
Speaker status indicator| Red light on| Speaker mute
Green light on| Speaker working normally
Localization Indicator| When the microphone detects a sound input, the indicator light in the
corresponding direction will be on

Note: When adjusting the volume, the blue light changes with the volume.The blue progress bar increases /decreases when adjusting the volume. When the volume is turned off, the indicator is red. After the volume is adjusted, the green light will return to on at an interval of 2s.

Connection Instructions

  • When no connection is made after the speakerphones turned on, the speakerph-one will automatically turn off after 15 minutes.
  • When connected correctly, open any video software, and select the speakerphone as default audio device, then you can start the meeting.
  • In the USB cascading mode, if the slave speakerphone turns off due to low power, you can connect it to computer or other terminal devices to charge, while it can function as the master speakerphone. Meanwhile, the original master speakerphone will work as the new slave speakerphone.
  • In Bluetooth and wireless cascading modes, if the master speakerphone or the slave speakerphone turns off due to low power, you can switch the connection USB cascading mode by connecting the master speakerphone to the USB port of the computer to charge and work.
  • Volume +/- , mute of the microphone/speaker of the master speakerphone and the slave speakerphone will be controlled synchronously.

5.1 USB Cascading Mode
Connect the two speakerphones with the 3.5mm audio cable. Use the original USB cable to connect the master speakerphone (either of the two speakerphones can be master or slave speakerphone) to the USB port of the computer.Tenveo
M5BEX Speakerphone - Indicator Function 1

5.2 Bluetooth Cascading Mode
Connect the two speakerphones with the 3.5mm audio cable. Firstly, turn on the master speakerphone (either of the two speakerphones can be master or slave speakerphone), then the OLED screen will display the . Long press the Bluetooth button for Bluetooth
pairing with the computer or other audio and video terminals. When the master speakerphone is successfully connected, turn on the slave speakerphone.Tenveo M5BEX Speakerphone - Indicator Function
2

5.3 Wireless Dongle Cascading Mode
Connect the two speakerphones with the 3.5mm audio cable. Plug in the wireless dongle to the USB port of the computer or other audio and video terminals, then turn on the master speakerphone. The OLED screen will display the . Long press the Bluetooth button for Bluetooth pairing with the computer or other audio and video terminals. When the master speakerphone is successfully connected, turn on the slave speakerphone.Tenveo M5BEX Speakerphone -
Indicator Function 3

5.4 Headset Cascading Mode
Connect to the headset jack using a 3.5mm headset cable. When the headset is connected, the speaker is automatically muted.Tenveo M5BEX Speakerphone -
Headset Cascading5.5 Switch among Master Speakerphone, Slave Speakerphone and Single Speakerphone, and Bluetooth Instruction

Single Speakerphone| This kit consists of 2 single speakerphones. Each of the 2 speakerphones can be used independently.
---|---
Master Speakerphone| In cascading mode, the one that connected to computer or other audio and video
terminals is defined as master speakerphone.
Slave Speakerphone| In cascading mode, the one that not connected to computer or other audio and video terminals, but connected to the other end of the 3.5mm audio cable, is defined as slave speakerphone.
Master Speakerphone-Slave Speakerphone-Single
Speakerphone| Master speakerphone and slave speakerphone can be switched. The one connected to audio source is
called master speakerphone, and the other one is called slave speakerphone. Either the master speakerphone or the slave speakerphone can be used independently (When not in cascading mode, the 2 speakerphones of this kit can be used independently).
Bluetooth Connection| 1.Press the Bluetooth button to turn on/off the Bluetooth connection; In cascading mode, short press the Bluetooth button to turn on/off the Bluetooth connection (when the master speakerphone connected to computer via USB, and the Bluetooth connection turned on at the same time, then the USB communication will stop automatically; when the master speakerphone connected to computer via Bluetooth and via USB for power charging, when Bluetooth connection disconnects, then the
USB connection will be adopted automatically).
2.  Long press the Bluetooth button for 10s, then Bluetooth pairing will be cleared .

Pickup Range

6.1 Pickup Range
Suitable for medium to large meetingsTenveo M5BEX Speakerphone - Pickup
Range 6.2 Application ScenariosTenveo M5BEX
Speakerphone - Application Scenarios

Technical Specifications

Item Name USB/Bluetooth Daisy Chain Speakerphone
Model No. M5BEX
Bluetooth BT5.0
Battery 8000mAH(Built-in lithium battery); Music time (up to 17 hours );

Battery life(call) up to 27 hours; Fastest charge time: 3 hours; Regular charge time :6 hours (Support PD2.0/3.0 charging, with maximum power up to 18W)
Connection Type| USB/Bluetooth/Wireless/3.5mm Jack (Daisy-chain version has 2×3.5mm Jack)
Meeting Room Size For Single Speakerphone| 15-30㎡
Meeting Room Size For Daisy Chain Speakerphone| 30-60㎡
Meeting Room Size For Daisy Chain Speakerphone| UP to 15 attendees
Meeting With Daisy Chain Speakerphone| Up to 20-30 attendees
Pickup Range for Single Speakerphone| 6 meters (19.68 feet)
Pickup Range for Daisy Chain Speakerphone| 12 meters (39.37 feet)
Mics for Single Speakerphone| 4x Digital Silicon Mics Array
Mics for Daisy Chain

Speakerphone

| 8x Digital Silicon Mics Array
Microphone Type| Omni-directional (360 degree pickup range)
Microphone Sensitivity| -38dB
Speaker Volume| 120dB
SNR| 62dB
Noise Reduction| Yes
Full Duplex Audio| Yes
AEC| Yes
Frequency Range| 135~20KHz
Speaker| 5W/120dB
Interface| 1 x Type-C, 13.5mm Daisy Chain Port, 1 x 3.5mm audio port
System Requirements| Windows 7/8/10 or above,MacOS 10.7 or above,Chrome OS V29.01547 or above
Application Support| Software: Skype, FaceTime, Zoom, Microsoft Teams, Hangouts, OBS, Xsplit, etc.
Working Temperature| -10°~+50°C
Storage Temperature| -10°~+60°C
Storage Humidity| 20%~90% RH (non-condensing)
Working Humidity| 20%~80% RH (non-condensing)
Power Supply| USB:5V DC @2A,9VDC@ 2A Maximum
1 Unit Size| Φ180mm×37.4mm
2 Units Size| 220×208×133mm(after packing)
2 Units Weight| 2
0.62kg/1.6kg(Net/Gross Weight)
Pack List| 2 Bluetooth Speakerphone, 1 USB Cable, 13.5mm Daisy Chain Cable, 1 Bluetooth Dongle, 1 OTG Adapter, 1 User Manual

Warranty

All products purchased from our company are guaranteed to keep in good re- pair for 36 months. If there are any quality problems during the guarantee per-iod, we will maintain them for free. Under any of the following conditions, relat- ed maintenance costs will be collected:

  1. Product was not normally used.
  2. Fire, electric shock, outside object collapse or other natural disasters causi-ng the equipment damaged.
  3. Unauthorized repair, misuse, abuse or change.

Warranty Card
Thank you very much for choosing our products.
User Info
Name ……………………………………
Tel ……………………………………..
Email …………………………………
Post code ………………………..
Address ………………………..
Product information
Product Name ……………………………
Factory Serial Number …………………
Fault description
……………………………………

Attention

  1. This card is considered as the Protection to fix warranty, so please reserve them carefully. Please fill in truthfully.
  2. Please indicate the model number, Factory Serial Number and the detailed description of the fault information.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals