ALLEN and HEATH DM48 Rack Ultra FX Mix Rack Installation Guide
- August 27, 2024
- Allen and Heath
Table of Contents
ALLEN and HEATH DM48 Rack Ultra FX Mix Rack
Specifications:
- Model(s): dLive DM0 / DM32 / DM48 / DM64 / CDM32 / CDM48 /CDM64
- Document Model(s): RackUltra FX Card Fitting Note ISS2 May 2024
Product Usage Instructions
Before Starting:
Fitting of the RackUltraFX card must be done by technically qualified personnel. Follow these steps before starting:
- Ensure a clean and clear worksurface.
- Check for adequate lighting.
- Use the correct tools listed below.
- Adhere to workshop safety requirements.
FAQ:
Q: Can I fit the RackUltraFX card myself?
A: Fitting of the card must be done by technically qualified personnel to
avoid damage and warranty issues.
Q: What should I do if I encounter difficulties during the fitting
process?
A: If you encounter any issues, refer to the provided fitting
instructions or contact customer support for assistance.
FITTING NOTE
| SUBJECT | RackUltra FX Card Fitting Note ISS2 |
|---|---|
| DATE | May 2024 |
| DOCUMENT | |
| MODEL(S) | dLive DM0 / DM32 / DM48 / DM64 / CDM32 / CDM48 / CDM64 |
Before Starting
Fitting of this card must be carried out by technically qualified personnel only. Any damage caused by mishandling or incorrect installation will not be covered under warranty.
This fitting note is intended to aid in the fitting of a RackUltraFX card to a
dLive MixRack.
Ensure a suitably sized worksurface is available. Ensure this is clear of
dirt, debris and obstructions which may damage the equipment surfaces. Ensure
adequate lighting. Use the correct tools for the job and ensure that they are
in good working order. Ensure all workshop safety requirements are adhered to.
Tools Required
- 1x T8 Screwdriver
- 1x T10 Screwdriver
- 1x Side Cutters
- 1x Grounding Strap
- 1x 004-1765-A 24V DC Wireform
- 1x M-DL-ULTRAFX-A RackUltra FX card
DM32 / DM48 / DM64
This section is not for the DM0.
-
Remove all screws holding the rear panel to the DM chassis.
-
Carefully move the rear panel away from the rest of the chassis.
- Do not damage the cable connecting the fan to the mainboard.
-
Remove all screws holding the top panel to the DM chassis.
-
Carefully move the top panel away from the rest of the chassis.
-
Remove the screws holding the DSP FX card to the card support bracket.
-
Remove the DSP FX card from slot C.
-
Fit RackUltra FX Card to slot D.
-
Fit the screws holding the RackUltra FX card to the card support bracket.
-
Refit the DSP FX Card to slot C.
-
Refit the screws holding the DSP FX card to the card support bracket.
-
Remove cable fitted at socket A and reconnect to socket C.
-
Fit cable 004-1765-A connecting socket A to socket B.
The cable excess should lie between the card support bracket and the rear panel. -
Cable 004-1765-A should be secured using a cable tie to the cable now fitted to socket C.
-
Flush cut excess on cable tie using side cutters.
-
Refit the top and rear panels as per steps 1 & 2.
-
Attach decals from kit provided (suggested fitting locations shown by arrows).
DM0
- Remove all screws holding the rear panel to the DM0 chassis.
- Carefully move the rear panel away from the rest of the chassis.
- Do not damage the cable connecting the fan to the mainboard.
- Fit the RackUltraFX Card to slot D.
- Fit the screws securing the RackUltraFX Card.
- Remove cable fitted at socket A and reconnect to socket C.
- Fit cable 004-1765-A connecting socket A to socket B.
- The cable excess should lie between the card support bracket and the rear panel.
- Cable 004-1765-A should be secured using a cable tie to the cable now fitted to socket C.
- Flush cut excess on cable tie using side cutters.
- Refit the rear panel as per steps 1 & 2.
- Attach decals from kit provided (suggested fitting locations shown by arrows).
CDM32 / CDM48 / CDM64
- Remove all screws holding the rear panel to the CDM chassis.
- Carefully move the rear panel away from the rest of the chassis.
- Do not damage the cable connecting the fan to the mainboard.
- Remove the screws holding the DSP FX card to the card support bracket.
- Remove the two screws holding the iMX6 card to the card support bracket.
- Remove screws holding the card support bracket to the CDM chassis.
- Remove the card support bracket from the CDM chassis.
- Fit the RackUltraFX Card to slot D.
- Replace the card support bracket and secure with screws.
- Replace the screws securing the DSP FX card.
- Fit the screws securing the RackUltraFX Card
- Remove cable fitted at socket A and reconnect to socket C.
- Fit cable 004-1765-A connecting socket A to socket B.
- The cable excess should lie between the card support bracket and the rear panel.
- Cable 004-1765-A should be secured using a cable tie to the cable now fitted to socket C.
- Flush cut excess on cable tie using side cutters.
- Refit the rear panel as per steps 1 & 2.
- Attach decals from kit provided (suggested fitting locations shown by arrows).
RackUltraFX Card Fitting Instructions ISS2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>