SUN GLOW Programming Resides with the Motor Instruction Manual

June 3, 2024
SUN GLOW

Programming Resides with the Motor
Instruction Manual
SUN GLOW Programming Resides with the Motor

MOTOR INFORMATION

  1. Ensure motor is protected. Any damages during transportation, storage, installation or misuse can cause the motor to not work properly.
  2. Charge the motor every 6 months to ensure optimal performance.
  3. If the battery charge is at a lower level, the motor will beep 10 times to prompt that it needs to be charged.
  4. Maximum running time of the motor is 6 minutes without limits. Motor will be asleep after six minutes has passed.
    Motor will still be in wake up/programming mode once the motor has restarted.

Programming resides with the motor. Each motor can store up to 20 copied channels.

CONTROL RANGE

**** SIGNAL STRENGTH AND RANGE MAY VARY DEPENDING ON THE ACTUAL ENVIRONMENT.

SUN GLOW Programming Resides with the Motor - CONTROL
RANGE

L1 Open Area L2 With Obstructions Emission Frequency
200m 35m 433.92/868 MHz

RECHARGING THE MOTOR

To recharge the motor’s battery, connect the SG DC charger to the motor head charging jack and plug the charger into a standard electrical outlet. When the battery is fully charged, the indication light on the charger will switch from red to green. You can also use the SG Solar Panel to keep the battery constantly charged while exposed to sufficient sunlight.

**** IF PURCHASING MORE THAN ONE CHARGER, PLEASE ENSURE THE OUTPUT VOLTAGE ON THE CHARGER AND MOTOR MATCH.

SUN GLOW Programming Resides with the Motor - fig1

MOTOR BUTTON LAYOUT

SUN GLOW Programming Resides with the Motor - MOTOR BUTTON
LAYOUT

REMOTE BUTTON LAYOUT

SUN GLOW Programming Resides with the Motor - Wall
Switch

BEFORE YOU BEGIN:

1. As a standard, motors are shipped in factory default mode without limits set.
2. Channel “0” cannot be programmed on a multi channel remote. It is intended to be a master channel for all motors.
3. Select the intended channel before activating wake-up mode, basic or advanced program settings.

STEP 1: PREPARING FOR PROGRAMMING

WAKE-UP MODE
(Must Be Done Before Basic & Advanced Programming)
Required to make the connection between the remote channel and the motor. During each of the following settings the time between each operation must be shorter than 10 seconds, otherwise the program will be canceled, and the motor will be back in default mode. Follow the steps below to wake-up the motor.

Note: No assigned limits in wake-up mode.

SUN GLOW Programming Resides with the Motor - HOLD

Test shade: Move shade by holding the up or down button to ensure that the motor works on the desired channel and moves in the correct direction.
Do not let the shade crash into the valance or unroll from the tube.

SWITCH DIRECTION

Test shade: Move shade up and down to ensure that the direction has been changed.
Do not let the shade crash into the valance or unroll from the tube.

STEP 2: BASIC PROGRAMMING

SETTING MOTOR LIMITS
Allows you to set two positions: the upper and lower limits. This can be applied to each shade per channel.
During limit setting, the time between two operations must be shorter than 2 minutes, otherwise the program will be cancelled, and the motor will be back in wake-up mode. Follow the steps below to set motor limits.

SUN GLOW Programming Resides with the Motor - HOLD
TOGETHER

Holding up or down will move the shade automatically
Test shade: Move shade up and down to test upper and lower limits. Refer to “Adjusting Motor Limits” if limits require fine tuning.

STEP 3: ADVANCED PROGRAMMING

ADJUSTING MOTOR LIMITS

SUN GLOW Programming Resides with the Motor - ADJUSTING MOTOR
LIMITS

SETTING A PREFERRED POSITION
Allows you to set a third limit position for the shade per channel. Follow the steps below to set a preferred position.
WHILE IN TILT FUNCTION SHADE WILL GO TO LOWER LIMIT FIRST AND THEN PROCEED TO THE PREFERRED POSITION.

SUN GLOW Programming Resides with the Motor - DELETING A PREFERRED
POSITION

When setup is complete, hold the stop button to go to the preferred shade position. Follow the steps above to program different preferred positions to separate channels on a 15 channel remote.

DELETING A PREFERRED POSITION

SUN GLOW Programming Resides with the Motor - GO TO

STEP 3: ADVANCED PROGRAMMING (CONTINUED)

SPEED ADJUSTMENT
Each motor has three speeds. To move between the different speeds, follow the diagram below.

SUN GLOW Programming Resides with the Motor - SPEED
ADJUSTMENT

TILT MODE INCREMENTAL MOVEMENT
Tilt mode is used to move the shade in small increments for fine adjustment. It is most effective when programmed with a standard remote (button remote). Follow the steps
below to set the shade in tilt mode or remove shade from tilt mode.

TILT MODE WILL REMAIN ACTIVE IN ALL MODES (Except Step 2: Basic Programming) UNLESS REMOVED

SETTING TILT MODE

SUN GLOW Programming Resides with the Motor - SETTING TILT
MODE

DELETING TILT MODE

SUN GLOW Programming Resides with the Motor - SETTING TILT
MODE2

Test shade: press the up or down buttons repeatedly for fine adjustment. To move shade automatically, hold the up or down buttons and release once the shade begins to move.

STEP 3: ADVANCED PROGRAMMING (CONTINUED)

COPYING, DELETING OR GROUPING WITH A REMOTE
The remote scenario chart below outlines different ways to copy, delete or group channels using separate remotes.

SUN GLOW Programming Resides with the Motor - COPYING, DELETING OR GROUPING
WITH A REMOTE

Separate channels can also be programmed this way within one 15 channel remote.
Follow the steps below to copy, delete or group channels.
COPYING/GROUPING CHANNELS

SUN GLOW Programming Resides with the Motor - COPYING

DELETING CHANNELS
Note : this only works on previously copied/grouped channels.

SUN GLOW Programming Resides with the Motor - DELETING
CHANNELS

COPIE OU SUPPRESSION D’UN MOTEUR PRÉCÉDEMMENT PROGRAMMÉ

DELETING OR TRANSFERRING GROUPS OF MOTORS ARE RECOMMENDED TO BE DONE USING THE ORIGINAL REMOTE THAT WAS SET UP.

SUN GLOW Programming Resides with the Motor - until motor jogs 1X
then

PERFORM FACTORY RESET ON MOTOR

Only perform a motor reset if necessary.

SUN GLOW Programming Resides with the Motor - HOLD until motor jogs
4X

STEP 3: ADVANCED PROGRAMMING (CONTINUED)

MOTOR SHIELDING
The mode allows a motor’s wireless radio signal to become temporarily disabled to save the battery life.

DISABLE SIGNAL:

SUN GLOW Programming Resides with the Motor - DISABLE ENABLE SIGNAL:

SUN GLOW Programming Resides with the Motor - DISABLE2

****If no limits are set, the motor will not move when enabled.

OPERATING SHADE AT MOTOR HEAD
This mode allows you to operate the shade in the event that the remote goes missing or is lost.

Note: pressing the motor setting button while the shade is moving can also stop the motor.

SWITCHING DIRECTION AT MOTOR HEAD
The change of direction can be done after limits have been set.

SUN GLOW Programming Resides with the Motor - SWITCHING DIRECTION AT MOTOR
HEAD

****Test shade: Move shade up and down to ensure that the direction has been changed.

Documents / Resources

| SUN GLOW Programming Resides with the Motor [pdf] Instruction Manual
Programming Resides with the Motor, Programming, Resides with the Motor, Motor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals