SUN GLOW Roller Shade Dual Square Fascia Instruction Manual

June 8, 2024
SUN GLOW

SUN GLOW Roller Shade Dual Square Fascia

WARNING

STRANGULATION HAZARD — Young children can be strangled by cords. Immediately remove this product if a cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible.

NOTE : Fabric-wrapped valances must be handled with care

PREPARATION

Component List

  • A. Front Shade
  • B. Back Shade
  • C. Fascia
  • D. Mounting Bracket
  • E. Chain Diverter
  • F. Chain Diverter Placeholder
  • G. Bracket Cover (Optional)

MOUNT THE BRACKETS

For inside mounts using ceiling and wall mount, brackets must be installed to ensure a 1/8” gap is left on each side for end caps.

CEILING MOUNT

Note : for ceiling mount ensure that the center and back mounting holes are used if the fascia cover is inverted. If the cover is not inverted, the front mounting hole may be used

WALL MOUNT

LATERAL MOUNT

INSTALL UPPER THE SHADE

NOTE : For shades with Zero Gravity, please refer to Zero Gravity instructions on page 4 at this stage.

STEP 3A: INSTALL PIN END FIRST

Put the spring loaded Pin End into the hole in the bracket.SUN-GLOW-Roller-
Shade-Dual-Square-Fascia-FIG- \(5\)

STEP 3B: INSTALL CLUTCH END

Keeping gentle pressure against the Pin End lift the clutch end up and align the two hooks on the clutch with the two slots in the bracket. The hooks should fall into place in the bracket, pull down gently to secure the blind into the bracketSUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG-
\(6\)

LOOP CHAIN AROUND BEARINGS (CHAIN ONLY)

If the upper shade being installed is a chain driven shade, ensure the chain falls behind the guide bearings

INSTALL LOWER THE SHADE

NOTE : For shades with Zero Gravity, please refer to Zero Gravity instructions on page 4 at this stag

STEP 5A: INSTALL PIN END FIRST

Put the spring loaded Pin End into the hole in the bracket.SUN-GLOW-Roller-
Shade-Dual-Square-Fascia-FIG- \(8\)

STEP 5C: INSTALL CLUTCH END

Keeping gentle pressure against the Pin End, lift the clutch end up and align the two hooks on the clutch with the two slots in the bracket. The hooks should fall into place in the bracket, pull down gently to secure the blind into the bracket.SUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG-
\(9\)

INSTALL THE CHAIN DIVERTER/PLACEHOLDER

Insert the front chain into the outside channel on the chain diverter, then insert the rear chain into the rear inside channel. Then insert the chain diverter into the mounting bracket until you here an audible click. Also insert the placeholder tab into the mounting bracket on the idle end. If not using a chain system, the diverter is replaced with a secondary placeholder .SUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG- \(10\)

INSTALL THE FASCIA

NOTE : For inside mount shades: snap the bracket covers on before hooking to the mounting brackets

  1. Hook the fascia on the top corner of the mounting brackets,
  2. then swing the bottom in. (3) You should hear a distinct click.

SUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG- \(11\)

INSTALL THE BRACKET COVERS

See step 2: For inside mounts, brackets must be installed to ensure a 1/8” gap is left on each side for end caps.SUN-GLOW-Roller-Shade-Dual-Square-Fascia-
FIG- \(12\)

  1. Remove backing from adhesive strips.
  2. Apply end caps to end brackets

INSTALL THE SAFETY SHIELD (CHAIN ONLY)

NOTE : For shades with chain operation only. Ensure that Safety Shield is carefully and properly installed.

Zero Gravity – Fascia or Open Roll Instructions

These steps are not required for Zero Gravity in Curved Cassettes. Skip these steps if using chain, Neo, or motorized control

  • If the Pin End of the shade appears as shown here, proceed with Steps 1,2 & 3 before returning to Step 4 of the Open Roll Installation Instructions
  • If the Pin End of the shade appears as shown here, proceed with Steps 4,5 & 6 before returning to Step 4 of the Open Roll Installation Instructions

PREPARING FOR INSTALLATION

NOTE : The blue shipping lock is used to lock the tension in place during shippingSUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG-
\(16\)

INSTALLING THE SYSTEM

  1. Insert the pin end of the blind into the bracket.
  2. Insert the hooked end into the other side bracket, and ensure the Zero Gravity head sits on the hooked teeth firmly. This should compress the hex plunger which releases the tension onto the shade.SUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG- \(17\)

TESTING THE SYSTEM

Always operate the shade from the center of the bottom bar. Ensure that the shade is balanced and does not want to roll up or down on its own. If it does, then the spring will require more or less tension to be perfectly balanced. If the shade requires more tension, turn the zero gravity head into the fabric, ie opposite direction to the fall of the fabric.SUN-GLOW-Roller-Shade-Dual-
Square-Fascia-FIG- \(18\)

WARNING

  • Do not pull the pin lockout until the shade is installed or tension will be released.
  • If tension has been released, see troubleshooting.

RUBBER BAND REMOVALSUN-GLOW-Roller-Shade-Dual-Square-Fascia-FIG-
\(19\)

Before installing the shade remove the rubber band holding the Pin Lock in place.

INSTALL SHADE AND REMOVE PIN LOCKSUN-GLOW-Roller-Shade-Dual-Square-
Fascia-FIG- \(20\)

  • Install roller shade while keeping Pin Lock toward you and held in place.
  • After installation remove the pin lock

TESTING THE INSTALLED ROLLER SHADE

Installed roller shade must be operated smoothly by the centre of the bottom bar to avoid excessive telescopingSUN-GLOW-Roller-Shade-Dual-Square-Fascia-
FIG- \(21\)

TROUBLESHOOTING

ONLY REQUIRED IF TENSION IS RELEASEDSUN-GLOW-Roller-Shade-Dual-Square-
Fascia-FIG- \(22\)

If the tension is released or removed accidentally follow these instructions:
The tension can be put back in any Zero Gravity Mini by turning the clutch head in the opposite direction of the fabric approximately 1 – 2 full rotations. While holding tension, insert the Pin Lock into the hole of the clutch. PROCEED WITH STEP 2 WHEN FINISHED.

Installation Instructions
Dual Square Fascia
2022-09-17 www.mysunglow.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals