SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia Instructions

June 3, 2024
SUN GLOW

Roller Shade
3” and 4” Fascia
Installation Instructions

Roller Shade 3 Inches and 4 Inches Fascia

WARNING
STRANGULATION HAZARD — Young children can be strangled by cords. Immediately remove this product if a cord longer than 22 cm or a loop exceeding 44 cm around becomes accessible.

NOTE: Fabric wrapped valances must be handled with care

PREPARATION

SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia

Component List
A. Shade
B. Fascia
C. Mounting Bracket
D. Chain Diverter
E. Chain Diverter Placeholder
F. Bracket Cover (Optional)
G. Safety Shield

MOUNT THE BRACKETS

Ensure a 1/8” gap is left on each side for end caps.

CEILING MOUNT WALL MOUNT LATERAL MOUNT

INSTALL THE SHADE

NOTE: For shades with Zero Gravity, please refer to Zero Gravity instructions on page 3.

STEP 3A: INSTALL PIN END
Install the Pin End into the hole in the bracket.SUN GLOW Roller Shade 3
Inches and 4 Inches Fascia - INSTALL PIN END

STEP 3C: INSTALL CLUTCH END
While keeping pressure against the Pin End hook the clutch onto the other bracket.SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia - CLUTCH
END

INSTALL THE CHAIN DIVERTER

Insert the chain into the channels as shown below. Then insert click the chain diverter and placeholder into the mounting brackets.SUN GLOW Roller Shade 3
Inches and 4 Inches Fascia - CHAIN DIVERTER

INSTALL THE FASCIA

First, snap the bracket covers on, then hook the fascia on the top of the mounting brackets, then swing the bottom of the fascia down until it clicks.SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia - THE
FASCIA

INSTALL THE SAFETY SHIELD

NOTE: For shades with chain operation only.

Zero Gravity Instructions

If the Pin End of the shade appears as shown here, proceed with Steps 1,2 & 3 before returning to Step 4 of the Open Roll or Fascia Installation Instructions

If the Pin End of the shade appears as shown here, proceed with Steps 4,5 & 6 before returning to Step 4 of the Open Roll or Fascia Installation Instructions

REMOVE THE SHIPPING LOCK

SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia - SHIPPING
LOCK

INSTALL THE SHADE

(A) Install the Pin End into the hole in the bracket.
(B) While keeping pressure against the Pin End hook the clutch onto the other bracket.

SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia - THE
SHADE

TEST THE SYSTEM

Draw and raise the shade from the middle of the bottom bar.
To increase tension use the spanner to turn the head in the opposite direction that the fabric falls off of the roll. To decrease tension turn toward the direction that the fabric falls off of the roll.

SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia - THE
SYSTEM

WARNING

  • Do not pull pin lock out until shade is installed or tension will be released.
  • If tension has been released, see troubleshooting.

REMOVE RUBBER BAND

Remove the rubber band holding the Pin Lock in place.SUN GLOW Roller Shade 3
Inches and 4 Inches Fascia - RUBBER BAND

INSTALL SHADE AND REMOVE PIN LOCK

Install the shade while keeping Pin Lock toward you and held in place, then remove the pin lock.SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia -
REMOVE PIN LOCK

ESTING THE SYSTEM

Pull and lift the shade from the middle of the bottom bar.

SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia - TESTING THE
SYSTEM

TROUBLE SHOOTING IF TENSION IS RELEASED
To increase tension, use the spanner to turn the head in the opposite direction that the fabricfalls off of the roll (approximately 1 – 2 full rotations). Insert the pin Lock into the hole of the clutch while holding the shade to keep the tension. PROCEED WITH STEP 5 WHEN FINISHED.

Documents / Resources

| SUN GLOW Roller Shade 3 Inches and 4 Inches Fascia [pdf] Instructions
Roller Shade 3 Inches and 4 Inches Fascia, Roller Shade, 3 Inches and 4 Inches Fascia, 4 Inches Fascia, Fascia
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals