MBE TEMIC MB Key Verification Tool Instruction Manual

MBE TEMIC MB Key Verification Tool

WIRING HARNESSES FOR CONNECTING TO IGNITION LOCKS OR IMMOBILIZERS

MERCEDES-BENZ W203

MERCEDES-BENZ W203

MERCEDES-BENZ W209/211/164/169

MERCEDES-BENZ W220

YOU MAY ENCOUNTER A W220 WITH A STEER I NG LOCK AND MECHANICAL GEARBOX.
IN SUCH CARS, THE BLUE PIN SHOULD BE MOUNTED ON THE SIXTH PIN IN THE RIGHT SOCKET OF THE IGNITION SWITCH.

MERCEDES-BENZ ‘W246/207

MERCEDES SPRINTER /VW CRAFTER

SKREEM l, 2, 3
SLK (Rl70), SL (Wl29), S-CLASS (Wl40), CROSSFIRE

WSP (TEMIC) l, 2, 3
SPRINTER W901-905 (2004-2007)

GETTING STARTED WITH THE DEVICE

ATTENTION! RATED SUPPLY VOLTAGE OF THE DEVICE IS 12V. SUPPLY VOLTAGE HIGHER THAN 13. 5V MAY DAMAGE THE DEVICE. REVERSING THE POLARITY WHEN CONNECTING THE POWER SUPPLY TO THE DEVICE MAY DAMAGE IT.
Before starting work with the device, it is necessary to switch the switches pos. 4, 6, 7 (PIC:. l) to the off position (0).
Set the voltage on the 12V power supply according to the instruction manual for the power supply you are using.
Connect the power cable to the power source. Red wire is power plus, black wire is power minus.
Select the wiring harness depending on the ignition switch you are going to connect.
Connect the wiring harness to the connector pos. 5 (PIC. l). Connect the ignition switch.
Connect the power cable to the device. Connector pos. l (PIC. l).
Move the power switch pos. 6 (PIC. 1) in the included position ( I ).

After that, the device will turn on and the following image will appear on the screen.

If you forget to connect the wiring harness, after a while the display will show the message “CABLE NOT CONNECTED”.

If during operation the ignition switch with CAN data bus “sleeps” (stops transmitting data on the CAN data bus), the display will show the message “CAN BUS SLEEP”.

Working with: Mercedes Sprinter/Vito, VW Sprinter

Latch connections are possible in the wiring harness being used. If a latch or latch emulator is not connected, then the built-in latch emulator must be enabled. To do this, you need to move the switch pos. 7 (PIC. l) in the included position ( I ).
If you do not insert the key into the ignition lock, the message “CAN BUS SLEEP” will be displayed on the screen.
After inserting the key into the iginition lock, the following information will be displayed on the screen.

If the key is not valid, then most lilkely the ignition switch will not wake up. After a while, the VIN number will be displayed in the “VIN” line, which is recorded in the ignition switch. The odometer line will display the mileage. Important! The mileage is not constantly written to the ignition lock, so the mileage may differ significantly from the recorded mileage in other parts of the car.
The “Remote” line displays the last pressed button on the key.

Possible options:

• Door Open
• Door Close
• Rear Door Open

The “Key Response” line will display the number under which this key is recorded in the ignition lock. Possible numbers l-8.
The 11 EZS11 line will display the status of the ignition switch.

Possible options:

• Key not detected
• Key detected
• ACC
• Ignition (15)
• Start Term (50)

Worki1ng with: Mercedes W203
The information that is displayed on the screen:

The “EZS” line displays the information “—” if the key is not valid or “Valid Key” if the key is valid.
The SSID line displays the key’s SSID.
The line “Odometr” displays the mileage that is recorded in the ignition switch.

Working with:
Mereedes W209/W2ll/W221/Wl 68/Wl 69/W251
The information that is displayed on the screen: 

The 11 EZS11 line displays the following information:

• Valid Key
• ACC
• Ignition (15)
• Start Term (50)

The SSID line displays the key’s SSID.
The line “Odometr” displays the mileage that is recorded in the ignition switch.
After a while, the VIN number will be displayed in the “VIN” line, which is recorded in the ignition switch.

Working with:
MercedesW202/W208/W210
The information that is displayed on the screen:

The “EZ5” line displays the information “Key not detected” if the key is not valid or “Key detected” if the key is valid.
The SSID line displays the key’s SSID.

Working with: Mercedes W246/W207
The information that is displayed on the screen:

The 11EZS11 line displays the information 11 Key not detected11 if the key is not valid or 11 Key detected” if the key is valid.
After a while, the VIN number will be displayed in the 11VIN 11 line, which is recorded in the ignition switch.

Working with:
SKREEM modules
SLK (Rl70), SL (Wl29)1, S-CLASS (Wl40), CROSSFIRE
You must also turn on Ignition before turning on the power.

If this is not done, the following message will be displayed on the screen:

The information that is displayed on the screen:

After a while, the VIN number will be displayed in the 11VIN11 line, which is recorded in the ignition switch.
The line 11 Last Remote11 displays the last remote control that was used for this immobilizer.
When lowering the key into the key hole pos. 3 in the 11Transponder11 line will display the number under which the transponder in the key is activated.
In the 11Keys11 line, the “X” symbol displays the positions to which the key has already been written.
In the 11Remotes11 line, the “X” symbol will display the positions to which the remotes have already been recorded.
In the 11Blocked Keys11 line, the “X” symbol will display positions that are reversibly blocked.

Working with:
WSP (TEMIC) modules Sprinter W910l-905 (2004-2007)
You must also turn on Ignition before turning on the power.

If this is not done, the following message will be displayed on the screen:

The information that is displayed on the screen:

The “Transponder” line displays information about the transponder of the key. Possible options:

• Not Valid
• Valid

In order for information about the! transponder to be displayed, it is necessary to lower the key into the hole pos. 3, turn off “Ignition” and turn on “Ignition”.
The “Remote” line displays information about whether the immobilizer worked on the command of the rE?mote control or not. In order to check, you need to hold the remote control! near the immobilizer radio module and press any button on the remote control. If all is well, the display will show “Worked” in the “Remote” line and turn off.
WWW.MBKEYPROG.COM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>