BEYOND H3 Running Man Combo Exit Sign Instruction Manual

Table of Contents

Specifications

Parameter	Description	Value
Model	JRMECW	Non-Maintained
Mode of operation		Supply Voltage
Output Voltage	4.5VDC
Output Power	4W
Lumen Output	150+Lm
Colour Temperature	6000K-7000K
Battery	3.6V 1000mAh Ni-Cd Battery
Max Charge Current (mA)	AC:110mA/DC:230mA
Max Discharge Current (mA)	800mA
Charging Time	24H
Discharge Time	90Min
LEDs	14 LEDS+2*1.2W LED lamp head
Net Weight	2.7LBS
Gross Weight	2.76LBS
IP Rating	IP20
Certification	UL Listed
Warranty	Five years warranty for the electrical parts and housing; Three

years warranty for battery.

Installation
To install the H3TM Running Man Combo Exit Sign LED Emergency Lights, follow these steps:

Ensure the power supply is turned off before installation.
Mount the exit sign in a prominent location that is easily visible in case of an emergency.
Connect the appropriate power supply as per the specified voltage requirements (120/347V/60Hz).
If needed, adjust the direction of the exit sign to ensure optimal visibility.
Once installed, test the functionality of the exit sign to ensure it illuminates properly during emergencies.

Dimensions

The dimensions of the H3TM Running Man Combo Exit Sign LED Emergency Lights are:

Frequently Asked Questions (FAQ)

Q: What is the warranty coverage for this product?
A: The product comes with a five-year warranty for the electrical parts and housing, and a three-year warranty for the battery.
Q: What is the IP rating of this product?
A: The product has an IP20 rating.
Q: What is the colour temperature of the LEDs?
A: The colour temperature of the LEDs is 6000K-7000K.

SKU # 155391
Output Power: 4W
Lumens: 150+lm
CCT: 6000K-7000K
Injection-molded thermoplastic ABS housing
Charging Time: 24H
Discharging Time: 90 MIN
Input Volt: 120/347V/60Hz
Battery: 3.6V 1000mAh Ni-Cd Battery
IP Rating: IP20
LED: 14 LEDS+2*1.2W LED lamp head
Certifications: UL Listed
Warranty: (5 years warranty for the electrical parts and housing; 3 years warranty for battery)”

Parameter	Descrip�on	Value

General

Performance

Three years warranty for battery

PICTOGRAM EXIT SIGN AND EMERGENCY LIGHT COMBINATION
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS

Review the diagrams thoroughly before beginning.
All electrical connections must be by local codes, ordinances, and the National Electric code.
Disconnect power at fuse or circuit breaker before installing or servicing.
Do not use outdoors.
Do not mount in hazardous locations, or near gas or electric heaters.
Do not let power cords touch hot surface.
Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
Do not use this equipment for other than intended use.
All servicing should be performed by qualified personnel only.
Allow the battery to charge for 24 hours before first use.

Use Flexible Conduit Only

SAVE THESE INSTRUCTIONS

AC Wiring

Open the front cover with flat screwdriver.
Insert the lamp heads at the corners of the main frame. Select the direction of lamp head before inserting.
Connect the male connector on the lamp head to the female connector on PCBA.

The fixture is suitable for wall mounting, side mounting, ceiling mounting.

Open front cover and assemble 2 pcs lamp heads on the frame.
Knockout appropriate mount screw hole and cable hole, and mount the back plate on the wall after feeding the building AC supply cable into the back plate(see Fig 3).
For ceiling and side mounting purposes, remove the mounting hole cover on the top or side of the unit, and assemble the canopy (see Fig 4,5,6).
Attach the crossbar to the junction box, set the longer blade of the crossbar touching the J-Box.
Route the proper wires through the mounting hole out of the housing.
Make electrical connections inside the J-Box as a wiring diagram.
Push excess wire into J-Box, use screws to tighten the canopy to the crossbar so that canopy is securely fastened and tight against the wall.
Attach the battery connector to PC board, restore the front cover on the unit, and adjust the position of lamp heads as need.
If the pictogram direction assembled not suitable, the pictogram can be taken out for change direction or replaced the pictogram, and then inserted into the diffuser easily(See Fig 7).

Using 1pc battery, no remote capability.
Using 2pcs battery with remote capability.
Connect the remote head extension wire to the remote wire, yellow is positive), purple is negative(-). connect wires using wire nuts.

Remote capability reference below: