BEYOND BALANCE 1675180051 Pull Up Dip Station Fitness Instruction Manual
- May 15, 2024
- BEYOND BALANCE
Table of Contents
BEYOND BALANCE 1675180051 Pull Up Dip Station Fitness
Included Hardware and Materials
- (A): [10] 1.5 black #8 screws
- (B): [2] 2 barrel-bolt with cap screw
- (C): [6] flat washers
- (D): [1] pull-up dowel, 31.25 x 1.5
- (E): [1] no-turn dip dowel, 31.25 x 1.5 with notch
- (F): [1] upper support with logo
- (G): [1] lower support
- (H): [2] arms, left and right
- (I): [2] diagonal supports
- (J): [1] velcro retaining strap
-
Step 1: Lower Assembly
-
Place diagonal supports on a flat surface, insert ends of lower support, and screw the black #8 screws into pre-drilled holes. Ensure screws are straight to prevent poking through pieces.
-
Step 2: Upper Assembly
Place arms upside down on a flat surface, insert upper support, apply wood glue inside the dowel holes, insert pull-up dowel and tighten screws for upper assembly. -
Step 3: Assembly Integration
Place the bottom assembly on a flat surface, place the upper assembly on top, align holes, insert barrel bolts with washers and tighten using screwdrivers. Repeat on the other side. -
Step 4: Final Setup
Loop the restraining velcro strap around the lower support and the rung to secure the accessory.
Congratulations! You are now ready to use your pull-up/dip bar!
FAQ
-
Q: How do I contact customer service for assistance?
A: For any questions, comments, or concerns, reach out to Beyond Balance at 281-813-9999 or info @kbeyond-balance.net. -
Q: Can I seek guidance from professionals for equipment usage?
A: Yes, you can consult qualified coaches, trainers, or therapists for guidance on using the equipment effectively.
Fitness Adjustable Pull-up and Dip Bar Assembly Instructions
Included Hardware and Materials
- (A): [10] 1.5″ black #8 screws
- (B): [2] 2″ barrel-bolt with cap screw
- (C): [6] flat washers
- (D): [1] pull-up dowel, 31.25″ x 1.5″
- (E): [1] no-turn dip dowel, 31.25″ x 1.5″ with notch (F): [1] upper support with logo
- (G): [1] lower support
- (H): [2] arms, left and right
- (I): [2] diagonal supports
- (J): [1] velcro retaining strap
Tools Required
- Phillips Screw Driver
- Electric Drill/Impact with Phillips Bit
- Wood Glue
- Tape Measure
-
STEP 1:
Place (I) diagonal supports on a flat surface, insert ends of (G) lower support, and screw (A) #8 screws into [4] pre-drilled holes as level as possible. (Figure 1) . Set assembly to the side.
Note: when installing any screws into pre-drilled holes throughout the installation make sure they are straight/level and not at an angle to prevent the tip of the screws from poking through any pieces.
-
STEP 2:
Place (H) arms upside down on a flat surface and insert (F) upper support (logo facing upside down and inwards). Partially screw (A) #8 screws into [4] pre-drilled holes. Apply wood glue inside the front [2] large dowel holes and insert (D) hardwood dowel into holes. Screw (A) #8 screws into the [2] pre- drilled holes as level as possible in (I) arms. Return to (F) upper support and tighten all screws for upper assembly. (Figure 2) -
STEP 3:
Place bottom assembly on a flat surface and place upper assembly on top of it, lining up the holes. (Figure 3) Insert (B) barrel bolt into hole with (C) flat washers : [1] washer will be located on the outside, [1] will be between the wood, and [1] on the inside against (I), followed by the cap screw. Screw in (B) barrel bolt on both ends using [2] screwdrivers to tighten. (Figure 4) Repeat on the other side.
Note: periodically check the barrel bolt on both ends and tighten if needed.
-
STEP 4:
Loop (J) restraining velcro strap around the lower support and the rung it is on to secure the accessory to your stall bar.
Congratulations!
You are ready to use your pull-up/dip bar!
At Beyond Balance customer service is our top priority. If at any time you have any questions, comments or concerns please reach out to us at: 281-813-9999 or info@beyond- balance.net
Use of our products is at your own risk. By purchasing this product you are assuming all responsibility for your own safety. As with all exercise equipment, any misuse of this product can result in injury, and by purchasing this product you agree that you are liable for any action taken with the product. Buyer understands and agrees that the use of the goods purchased from Beyond Balance may be dangerous to human safety, may result in injury or death and present a risk of damage to property if not used properly. You must routinely inspect your equipment for any wear or tear which can occur after repeated use. We are not responsible for any mishaps, injuries or damages resulting from your use of our products.
As with any training program or other physical activity performed on these items, there is a risk of injury and proper supervision is required. Purchaser assumes responsibility and acknowledgment of all risk factors. For more training and safety information, we recommend online information from qualified coaches, trainers, and therapists or bringing some of your equipment to your gym/coach/trainer/therapist.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>