Beyond Balance Fitness Stall Bars Instruction Manual
- May 15, 2024
- BEYOND BALANCE
Table of Contents
Beyond Balance Fitness Stall Bars
Specifications
- Side Uprights: 90 inches
- Back Plates: 34 inches
- Hardwood Rungs: 15 pieces, 33.375 inches each
- Stud Mounting Screws: 4 pieces, 3 #10 size
- Black #8 Screws: 42 pieces, 1.5 inches each
Product Usage Instructions
-
Step 1: Assemble the Uprights and Dowels
Place one upright on the floor with holes facing up. Insert each of the 15 hardwood dowels fully into the holes. -
Step 2: Secure the Dowels
Gently place the upright on its side and start inserting the black screws into each pre-drilled hole to secure all dowels to the upright. -
Step 3: Attach the Second Upright
Add glue to the second upright pockets and align it with the dowels on the first upright. Secure the dowels by inserting screws into the pre-drilled holes. -
Step 4: Check Assembly Width
Measure the width of the assembly to ensure it is 34 inches at the top, middle, and bottom. Adjust dowels if needed to achieve correct dimensions. -
Step 5: Install Backplates
Place the assembly facing down and install the backplates using the black screws provided. Ensure the logo is positioned correctly.
Mounting to the Wall
Congratulations! Your fitness stall bar is now ready to be mounted to the wall
securely.
FAQ
- Q: Can I adjust the height of the hardwood rungs?
A: The hardwood rungs are fixed at a specific height and cannot be adjusted.
Fitness Stall Bar Assembly Instructions
Included Hardware and Materials
- (A): [42] 1.5″ black #8 screws
- (B): [2] Side Uprights, 90″
- (C): [2] Back Plates. 34″
- (D): [15] Hardwood Rungs, 33.375″ (E): [4] 3″ #10 stud mounting screws
Tools Required
- Electric Drill or Impact with Phillips Bit
- Wood Glue
- Tape Measure
-
STEP 1: Place (B) upright on the floor with holes facing up.
*Recommended: Add a small amount of wood glue in each hole and spread to prevent running. Insert each of the 15 hardwood dowels fully into the holes
-
Floor
STEP 2: Gently place (B) upright on its side and start inserting (A) black 1.5″ screws into each of the pre-drilled holes as straight as possible securing all 15 dowels to (B) upright.
Note: when installing any screws into pre-drilled holes throughout the installation make sure they are straight/level and not at an angle to prevent the tip of the screws from poking through any pieces.
-
STEP 3: Add glue to second upright pockets and spread lightly. Rotate (B) upright on its side (dowels facing up) and align the second (B) upright into all holes and insert (A) black 1.5″ screws into each of the pre-drilled holes as straight as possible securing all 15 dowels to (B) upright.
-
STEP 4: Once all dowels are secured, measure the width of the assembly and confirm 34″ at top, middle, and bottom. If the assembly is larger than 34″ then all dowels are not seated fully. Loosen, seat fully, and re-tighten screws. Measure to confirm correct dimensions.
Note: Due to our tight tolerances, dowels can be tapped with a wood block or rubber mallet to fully seat if necessary. -
STEP 5: Place assembly facing down in order to install (C) backplates. Two black 1.5″ screws are required at each of the (4) locations from the back and one black 1.5″ screw is required from the side of the finger joint as straight as possible. (FIgures 4 & 5)
Note: Confirm logo is right side up
Congratulations!
You are ready to mount your bars to the wall.
At Beyond Balance customer service is our top priority. If at any time you
have any questions, comments or concerns please reach out to us at:
281-813-9999 or info@beyond-balance.net
In addition to this instructional packet you can view our instructional
assembly video at beyond-balance.net on the product page and installation
videos at our FAQ page.
Use of our products is at your own risk. By purchasing this product you are assuming all responsibility for your own safety. As with all exercise equipment, any misuse of this product can result in injury, and by purchasing this product you agree that you are liable for any action taken with the product. Buyer understands and agrees that the use of the goods purchased from Beyond Balance may be dangerous to human safety, may result in injury or death and present a risk of damage to property if not used properly. You must routinely inspect your equipment for any wear or tear which can occur after repeated use. We are not responsible for any mishaps, injuries or damages resulting from your use of our products.
As with any training program or other physical activity performed on these items, there is a risk of injury and proper supervision is required. Purchaser assumes responsibility and acknowledgment of all risk factors. For more training and safety information, we recommend online information from qualified coaches, trainers, and therapist or bringing some of your equipment to your gym/coach/trainer/therapist.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>