BEYOND BALANCE PSSE Freestanding Stall Bars Instruction Manual
- May 15, 2024
- BEYOND BALANCE
Table of Contents
BEYOND BALANCE PSSE Freestanding Stall Bars
Product Information
Specifications:
- Dimensions: 34″ x 33.375″ x 90″
- Materials: Hardwood oval rungs, metal hardware
Product Usage Instructions
Step 1: Assemble Uprights and Rungs
Place the side upright (J) on the floor with holes facing up.
Add wood glue to each hole and insert the 13 oval rungs fully.
Secure the rungs with black screws (A).
Step 2: Attach Second Upright
Add glue to the second upright and align it with the rungs. Secure with black
screws (A).
Step 3: Check Dimensions
Measure the width of the assembly to ensure it is 34″. Adjust dowels if needed
by tapping them with a mallet.
Step 4: Install Backplates
Place the assembly facing down and install backplates (K) using black screws
(A).
Step 5: Base Assembly
Attach angle brackets (I) to base legs (O) using pan head bolts (D). Align
holes with brackets and secure with bolts.
Step 6: Attach Upright Assembly
Insert upright assembly into base assembly slots and secure with screws (C).
Tighten hardware inside the base leg.
Step 7: Install Diagonal Supports
Insert diagonal supports (M) into the back of the base assembly using barrel
bolts (B) and cap screws.
FAQ
Q: What tools are required for assembly?
A: You will need a rubber mallet, screwdriver, and wrench for assembly.
Q: Can the dowels be adjusted if not seated fully?
A: Yes, you can tap the dowels with a wood block or rubber mallet to
fully seat them.
Included Hardware and Materials
- (A) : [38] 1.5″ black #8 screws
- (B) : [4] 2″ barrel bolts with cap screw
- (C) : [6] 2.5″, 41 x 20, pan head bolts
- (D) : [8] 1″, 41 x 20, pan head bolts
- (E) : [6] flat washers
- (F) : [6] lock washers
- (G) : [6] 41 x 20 nuts
- (H) : [6] 41 x 20 rounded cap nut
- (I) : [2] black corner brackets
- (J) : [2] side uprights (left and right), 90″
- (K) : [2] back plates, 34″
- (L) : [13] hardwood oval rungs, 33.375″
- (M) : [2] diagonal supports
- (N) : [1] base back support
- (O) : [2] base legs (left and right)
- (P) : [2] weight bags
Tools Required:
- Electric Drill or Impact with Phillips Bit
- Wood Glue
- Tape Measure
- 167 ” Wrench
- Phillips Screw Driver
Assembly Instructions
STEP 1: Place (J) upright on the floor with holes facing up.
Recommended: Add a small amount of wood glue in each hole and spread to
prevent running. Insert each of the 13 oval dowels fully into the holes
STEP 2: Gently place (J) upright on its side and start inserting (A) black 1.5″ screws into each of the pre-drilled holes securing all 13 oval dowels to (J) upright.
STEP 3: Add glue to second upright pockets and spread lightly. Rotate (J) upright on its side (dowels facing up) and align the second (J) upright into all holes and insert (A) black 1.5″ screws into each of the pre-drilled holes securing all 13 oval dowels to (J) upright.
STEP 4: Once all dowels are secured, measure the width of the assembly and confirm 34″ at top, middle, and bottom. If the assembly is larger than 34″ then all dowels are not seated fully. Loosen, seat fully, and re-tighten screws. Measure to confirm correct dimensions.
Note: Due to our tight tolerances, dowels can be tapped with a wood block or rubber mallet to fully seat if necessary.
STEP 5: Place assembly facing down in order to install (K) backplates. Two black 1.5″ screws are required at each of the (4) locations from the back and one black 1.5″ screw is required from the side of the finger joint. (FIgures 4 & 5)
Note: Confirm logo is right side up
STEP 6: Set upright assembly to the side.
STEP 7: Base assembly:
Locate (O) left and right making sure that the pre-drilled holes for (I) are
on the inside of the assembly. Install (I) angle bracket to the inside of (O)
by inserting two of the (D) 1″ bolts. Once both sides are installed, align (N)
holes with the (I) angled brackets and insert the remaining (D) 1″
bolts.(Figures 6 &7)
Note: Do not fully tighten assembly until the very last step.
STEP 8: Locate the upright assembly, insert into the slots of the base assembly, and insert three (C) screws into each (O) base leg from outside to inside. (Figure 8). From inside of leg install the hardware in order (E) (F) (G) (H). (Figure 9).
Note: Do not fully tighten assembly until the very last step.
STEP 9: Locate (M) diagonal supports and insert into the slot located on the back of the base assembly. Starting from the base insert the (B) barrel bolt from outside to inside and screw in cap screw. Repeat on second side. (Figure 11)
STEP 10: Align the (M) diagonal on the outside of the (J) hole and insert (B) barrel bolt and corresponding cap screw. Repeat on second side. (Figure 10)
STEP 11: Tighten all hardware completely.
STEP 12: Now that the upper and lower assemblies are attached and fully
tightened you can fill up (P) weight bags with either sand or water* and strap
to (M) diagonals while resting on the base assembly.(Figure 12)
If using water, remove and empty after each use.
Congratulations!
You are now ready to use your freestanding stall bars.
At Beyond Balance customer service is our top priority. If at any time you have any questions, comments or concerns please reach out to us at: 281-813-9999 or info@beyond- balance.net
Use of our products is at your own risk. By purchasing this product you are assuming all responsibility for your own safety. As with all exercise equipment, any misuse of this product can result in injury, and by purchasing this product you agree that you are liable for any action taken with the product. Buyer understands and agrees that the use of the goods purchased from Beyond Balance may be dangerous to human safety, may result in injury or death and present a risk of damage to property if not used properly. You must routinely inspect your equipment for any wear or tear which can occur after repeated use. We are not responsible for any mishaps, injuries or damages resulting from your use of our products.
As with any training program or other physical activity performed on these items, there is a risk of injury and proper supervision is required. Purchaser assumes responsibility and acknowledgment of all risk factors. For more training and safety information, we recommend online information from qualified coaches, trainers, and therapist or bringing some of your equipment to your gym/coach/trainer/therapist.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>