Beyond BWS18218 Verandah LED 18 inch Black Bath Vanity Wall Light Installation Guide

Beyond BWS18218 Verandah LED 18 inch Black Bath Vanity Wall Light

Safety Instruction

WARNING

IMPORTANT:
NEVER attempt any work without shutting off the electricity.

• Read all instructions before installing.
• The system is intended for installation in accordance with the National Electrical Code (NEC), other applicable installation code(s), and local regulations by a licensed electrician familiar with the operation of the product and the hazards involved.
• Go to the main fuse box or circuit breaker panel. Place the main power switch in the “OFF” position and unscrew the fuse (s) or switch ”OFF” the circuit breaker switch (es) that controls the power to the fixture (s) or room that you are working on.
• Place the wall switch in the “OFF” position.
• FAILURE TO INSTALL THIS FIXTURE IN ACCORDANCE WITH THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH AND/OR PROPERTY DAMAGE.

CAUTION

• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL Listing of this fixture.
• When handling the fixture, do not apply pressure to the LEDs or bulbs. Hold the fixture by the base only.
• Do not exceed the maximum wattage noted on the fixture. Use only the recommended LED or standard lamps with the fixture.

HARDWARE

PREPARATION

1. Shut off the power at the circuit breaker and remove the existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts in a clear area. Be careful not to lose any small parts necessary for installation.

MOUNT ON 2×4＂SWITCH BOX

(Fig. 1/ Fig. 3)

1. Remove the mounting screw (B) from the mounting plate.

2. Remove the crystal holder from the fixture;

3. Insert the crystal into the crystal holder and fix it with an Allen screw (G) and an Allen wrench (H).

4. Secure the crystal holder on the fixture with a screw (J).

5. Drill holes in the wall aligned with the keyholes located in the mounting plate, and insert the plastic anchor (D).

6. The lamp can switch between three color temperatures (3000K-3500K-4000K), which can be adjusted to your preference with the switch in the canopy (Fig.5).

7. Secure the mounting plate to the switch box using standard junction box screws that comes with the switch box. Fasten it to the wall using a wood screw (C) onto the plastic anchor(D), Hook the safety cord to the mounting plate.
   Note:

8. using any other non-original-manufacturer-provided Switch box screw may result in safety issues;

9. The side of the mounting plate marked “GND” must face out.

10. Connect the Fixture input wires to switch box wires as shown in Fig.4, making sure that all wire connectors (A) are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the screw provided after all wires are connected tuck them carefully the switch box.

11. Secure the fixture to the mounting plate using the mounting screw (B).

MOUNT ON 4×4＂JUNCTION BOX

(Fig. 2/ Fig. 3)

1. Remove the mounting screw (B) from the mounting plate.

2. Remove the crystal holder from the fixture;

3. Insert the crystal into the crystal holder and fix it with an Allen screw (G) and an Allen wrench (H).

4. Secure the crystal holder on the fixture with a screw (J).

5. Drill holes in the wall aligned with the keyholes located in the mounting plate, and insert the plastic anchor (D).

6. The lamp can switch between three color temperatures (3000K-3500K-4000K), which can be adjusted to your preference with the switch in the canopy (Fig.5).

7. Secure the mounting ring (F) to the junction box using junction box screws. The side of the mounting plate
   marked “GND” must face out.

8. Secure the mounting plate and conversion plate(E) to the mounting ring (F) using junction box screws as shown in Fig. 2. Fasten it to the wall using wood screw (C) onto the plastic anchor(D). Hook the safety cord to the mounting plate.
   Note:

9. Using any other non-original-manufacturer-provided junction box screw may result in safety issues;

10. The side of the mounting plate marked “GND” must face out.

11. Connect the Fixture input wires to junction box wires as shown in Fig. 4, making sure that all wire connectors (A)
    are secured. If your outlet box has a green or bare copper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground wire directly to the mounting plate using the screw provided after all wires are connected tuck them carefully into the junction box.

12. Secure the fixture to the mounting plate using the mounting screw (B).

Conversion Plate Dimensions

Mounting Plate Dimensions

Mounting Ring Dimensions

Contact Information

Schonbek, 61 Industrial Blvd, Plattsburg, New York, 12901| Phone: 1-800-836-1892 | Fax: 518-563-4228 www.schonbek.com | JAN 2022.

References

• Schonbek 1870 | Lighting that Lives Forever

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>