iBoard IB-175C Fifth Generation 6 Inch Stainless Steel Running Boards Side Step Installation Guide
- August 22, 2024
- iBoard
Table of Contents
iBoard IB-175C Fifth Generation 6 Inch Stainless Steel Running Boards
Side Step
Specifications:
- Product Name: Rocker Panel Mount
- No drilling required
- Part Number : IB-175C&H
Product Usage Instructions
-
Step
Start the installation under the passenger side of the vehicle. Locate the front factory running board mounting location along the inner side of the body, (Fig 1). -
Step
Slide (1) 8mm Plastic Washer over each factory mounting stud in the body panel, (Fig 2 & 3). IMPORTANT : M8 Plastic Washers are designed to prevent corrosion between the aluminum body panel and the steel mounting brackets. -
Step
Select (1) Mounting Bracket. Attach the Mounting Bracket to the (3) factory studs on the Passenger Side Front Mounting Location with (3) M8 Large Flat Washers and (3) M8Χ1.25 Nylon Lock Nuts, (Fig 4). Snug but do not fully tighten the hardware.
NOTE : All (6) Mounting Brackets are universal. -
Step 4
Repeat Steps 1—3 to install the (2) remaining Passenger Center and Rear Mounting Brackets. -
Step 5
Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 5 & 6) -
Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts;
-
Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider.
-
Slide the Slider (with carriage bolts) to the Step Bar.
-
Repeat to install the other (2) sliders to the step bar.
-
Attach the Step Bar (with the Sliders) to the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 6). Do not fully tighten hardware at this time.
Note : The Sliders are packed with the Step Bars. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!!
Attention
Do periodic inspections to the installation to make sure that all hardware is
secure and tight. In order to protect your bars/boards, please use mild soap
/non-abrasive products for cleaning only.
Attention:
Do periodic inspections to ensure that all hardware is secure and tight.
READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED.
- ROCKER PANEL MOUNT
- NO DRILLING REQUIRED
PART #: IB-175C&H
Scan for Installation Video
| Fastener Size | Tightening Torque (ft-lbs) | Required |
|---|---|---|
| 6mm | 6-7 | X |
| 8mm | 16-18 | √ |
| 10mm | 31-32 | X |
| 12mm | 56-58 | X |
| 14mm | 92-94 | X |
PART LIST
Mounting Bracket List
Item| QTY| Description| Item| QTY| Description
1#| 6| Mounting Brackets| | |
Hardware Package A (For Bracket Installation)
Item| QTY| Description| Item| QTY| Description
1#| 18| M8 Plastic Washers| 3#| 18| M8X1.25 Nylon
Lock Nuts
2#| 18| M8 Large Flat Washers| | |
Hardware Package B (For Stainless Steel Step Bar Installation)
Item| QTY| Description| Item| QTY| Description
1#| 12| M8X1.25-35mm Carriage Bolts| 3#| 12|
M8 Nylon Lock Nuts
2#| 12| M8 Large Flat Washers| 4#| 6| Sliders
(Packed with Step Bars)
Customer Support : info@iboardauto.com
FAQ
Q: What should I do if I encounter missing parts during installation?
A: If you notice any missing parts, please contact customer support at
info@iboardauto.com for assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>