PYRAMID PB317X Car Stereo Amplifier Instruction Manual
- August 24, 2024
- PYRAMID
Table of Contents
PYRAMID PB317X Car Stereo Amplifier
All Pyramid products are carefully constructed and thoroughly tested before shipment, products purchased in the USA are warranted to be free of defects in material and workmanship for two (2) years from the date of purchase. This warranty is limited to the original retail purchase. Should the product fail due to factory defects in material or workmanship, your unit will be repaired or replaced at the sole discretion of Pyramid. To obtain warranty service you must first call our Consumer Return Hotline number at (718) 236- 6948 to obtain a Return Authorization number. This R . A . # Must appear on the outside of your package and on all paperwork relating to your return.
R. A. # Pyramid Service Center 1600 63RD Street Brooklyn, NY 11204
You must also include the following items: A copy of your sales receipt or other proof of purchase
- A brief letter indicating the problem you are experiencing
- include in your letter your return address, daytime phone number, and R. A. Number
- also include a check or order for $ 18, 00 for return shipping, handling, and insurance, or provide your Visa/MC number with expiration date.
Our obligation under this warranty is limited to the repair or replacement of the defective unit when returned to us prepaid. This warranty will be considered void if the unit was tampered with, improperly serviced, or subject to misuse, neglect, or accidental damage.
limited warranty policy
Congratulations…
On your purchase of a Pyramid Arctic Series amplifier. This amplifier
extends the pyramid tradition into a totally new series of amps, designed from
the ground up to deliver the power, performance and flexibility the modern car
audio enthusiast demands. When you check the list of features offered by the
PB317X,PB417X,PB617X,PB/17Х,PB1217X, and PB1617X, you’ll know you made the
right choice with a Pyramid Power amplifier.
precautions
Do not operate the amplifier when it is unmounted, Attach all audio system components securely within the automobile to prevent damage, especially in an accident. Do not mount this amplifier so that the wire connections are unprotected, or in a pinched condition, or likely to be damaged by nearby objects. Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, do so only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage that isn’t covered in the manufacturer’s warranty.
Protection circuitry
The built-in protection circuitry in the pyramid Arctic amplifiers will disable the amplifier if it senses an input overload, a speaker short circuit, or extreme temperature conditions. When the protection circuit is activated by any of these conditions, the Protection LED will be illuminated. If this occurs, carefully inspect the system to determine the source of the problem. If the shutdown was a result of a thermal overload condition, allow the amplifier to cool down before attempting to restart it. If the shutdown was a result of an input overload, or speaker short circuit, be sure to corr the condition before restarting. The amplifier can be restarted by turning the remote power OFF and then ON again.
troubleshooting
No output.
Confirm that all terminal strip connections are secure and tight. Check both
in-line and built-in fuses. Both the +12V and the Remote terminals must have +
12V referenced to chassis ground. Confirm that the audio signal source(car
radio, equalizer, etc.) Is connected and is supplying output signal. To check
if the amp is supplying signal, unplug the cables from the signal source(but
leave them plugged into the amp). Briefly tap the center pin of each of the
disconnected RCA plugs with your finger. This should produce a noise)feedback)
in your speakers.
Only one channel works.
Confirm that all terminal strip connections are secure and tight. Check the
Balance control on the head unit(or other source) to verify that it is set to
its midpoint. If you are using the Low Level RCA input, reverse the input
plugs at the amplifieri.e.,switch the L with the R). If the channels which is
silent switches to the other side, the problem is either in the head
unit/other source or the connecting cables.
Weak output.
Readjust the Input Level Controls) to better suit the input signal.
Noise in the audio
If the noise is a “whine” whose pitch follows the engine speed, confirm that
the amplifier and any other signal sources(hesd unit, etc.) Are properly
ground. If the noise is a “clicking” or “popping” noise whose rate follows the
engine speed, this usually means that the vehicle is equipped with resistor
spark plugs and wires, or that the ignition is in need of service. Check the
routing of the speaker and input wires to make sure they are not adjacent to
wire which interconnect lights and other accessories. If the above steps fail
to improve or clear noise interference, the system should be checked by a
professional mobile audio installer.
general features
PB317X
High Performance 800Watt 2 channel Bridgeable MOSFET Amplifier
- 400 WattsX 2 Output
- 800 Watts X 1 Bridged Output
- Variable Hi/Lo Electronic Crossover Network
- Variable Bass Boost(0-6-+ 12dB@60Hz)
- Variable Input Level(Gain) Control
- Remote Turn on/Off
- RCA Inputs
- High Level MOLEX Indicator
- Power ON LED Indicator
- LED Protection Indicator
- S/N Ratio: >95dB
- THD :<0.2%
- Thermal Protection
- Overload Protection
- Short Circuit Protection
- Anti-Thump Turn-On
Mounting and installation
Your new PYRAMID Arctic Series amplifier comes complete with the required mounting hardware. When determining a suitable location in your vehicle for the amp, please remember that it is a high-power electronic device capable of generating high heat. For this reason, always choose a location in your vehicle that has low vibration, adequate ventilation, a minimum of dust, and no moisture. Be sure to mount the amp in such a manner as to allow reasonable airflow over the cooling fins. Mark the location for the mounting screw holes by positioning the amp where you wish to install it and use a scribe (or one of the mounting screws) inserted in each of the mounting holes to mark the mounting surface for the mounting surface. If the mounting surface is carpeted, measure the hole centers and mark them with a felt tip pen. Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your vehicle which may be located behind the mounting surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely.
When making electrical connections to your amplifier, please observe the
following
Use at least 8 gauge wire for power and ground connections. Wire the amplifier
directly to the car battery. For the ground connection, use the shortest
possible wire to a good chassis ground point. Wire the Remote connection to
the auto start lead of your head unit, equalizer or power antenna.
About power fuses
Pyramid Arctic Series amplifiers feature built-in fuse systems. These fuses
protect both the amplifier and the electrical system in your vehicle from
fault conditions. If you ever need to replace the fuse in your Pyramid Arctic
Series amp, use a fuse of exactly the same type and rating. A different type
or rating of fuse may result in damage or fire.
Speaker connections
4ch amp PB417X PB617X PB1617X
2CH Bridged Output Mode With Subwoofer Output
PB417X
High-Performance 1000Watt 4 channel Bridgeable MOSFET Amplifier
- 250 WattsX 4 Output
- 500 Watts X 2 Bridged Output (250WX 2+500WX 1)
- Variable Hi/Lo Electronic Crossover Network
- Variable Bass Boost(0-6-+ 12dB@60Hz)
- Variable Input Level(Gain) Control
- Remote Turn on/Off
- RCA Inputs
- High-Level MOLEX Indicator
- Power ON LED Indicator
- LED Protection Indicator
- S/N Ratio: >95dB
- THD:<0.2%
- Thermal Protection
- Overload Protection
- Short Circuit Protection
- Anti-Thump Turn-On
Features and specifications
2ch amp PB317X PB717X
2ch amp PB317X PB717X
2ch amp PB317X PB717X
4ch amp PB417X PB617X PB1617X
2ch amD PB317X PB717X