darklab airbolt Machine Battery User Manual
- June 5, 2024
- darklab
Table of Contents
Machine Battery
USER MANUAL
SAFETY NOTICE
CLASS III SYMBOL
A Class III appliance is designed to be supplied from a separate/safety extra
low voltage (SELV) power source. The voltage from a SELV supply is low enough
that under normal conditions a person can safely come into contact with it,
without the risk of electrical shock. The extra safety features built into
Class I and Class II appliances are, therefore, not required. For medical
devices, compliance with Class III is not considered sufficient protection,
and further more-stringent regulations apply to such equipment.
TECHNICAL DATA|
---|---
Operating Voltage:| 5-12 V DC
Current:| UP T01.0 A
Ambient Temperature:| +10 to +35 °C
Relative Humidity:| 30 to 75%
Dimensions (0 X L):| H56 x W49 X L27 mm
Weight:| Approx. 58g (2oz)
Charging Port:| USB-C
BARRIER PROTECTING YOUR MACHINE
We strongly suggest the use of barrier products to protect your machine. For a
visual demonstration of barrier protection methods, please visit our YouTube
channel, FK Irons.
This device is only for use by trained tattoo artists and not for use by
children or persons with reduced physical, sensory or mental capabilities.
AIRBOAT INTRO
THE AIRBOAT / AIRBOAT MINI
Unleash Your Powe
The first wireless battery features complete Bluetooth connectivity and a
whole new sense of freedom.
OVERVIEW
SPECIFICATIONS
- Output Voltage: 5 – 12 V
- Increment/decrement voltage interval: 0.5 V
- Maximum output current: 1.0 A
- Charger Input: USB-C
- Size: H56mm x W49mm x L27mm
- Weight: Airbolt 121g (4.2 oz) Airbolt Mini 96g (3.4 oz)
- Battery life: Up to 10 hours, depending on usage
Range will vary based on, but not limited to, cartridge, stroke,
voltage, needle Grouping, motor, and pigment viscosity.
The device should only be recharged with a USB Approved/Certified Class 2 Power unit charger marked 5 Vdc, 2000mA
FEATURES
Features:
- Higher energy density to provide high reliability and stability
- Dynamic power path management: USB-C Li-Ion battery
- Auto-shutdown (State of Charge (SoC) < 3%)
- Automatic jumpstart feature
- Fast charging speed: up to 1.0 A
- Extremely compact, convenient to carry
- Compatible with FK Irons and Darklab products
- Bluetooth enabled, pair with Darklab app
- Device firmware update functionality via the app
- Shipping mode functionality
- Software reset
Compatible with all FK Irons Spektra RCA machines, as well as most RCA machines on the market.
GETTING STARTED
For your safety, this power unit has been shipped disabled. To activate, plug into a USB-C power source and charge completely until the LED light remains solid green. It’s important to charge for a minimum of 3 hours prior to first use.
Automatic Fault Detection:
Overcharge Detection (OVP)
Over-Discharge Detection (UVP)
Charge Overcurrent Detection (OCC)
Discharge Overcurrent Detection (OCD)
Load Short-Circuit Detection (SCP)
Menu Modes: Press and hold the power button.
Hard shut off: Hold the power button until The LED indicator is red, the
battery is now disabled. To re-activate the battery, plug it into any USB-C
power source.
Device reset:
eGIVE
eGIVE ADJUSTMENT
With this feature, you’ll be able to control the amount of “give” or
resistance of the needle upon impact with the skin. This enables the artist to
take advantage of the softness or hardness of a hit to achieve specific
results. 0 no effect, 5 maximum amount of eGive.
ADDITIONAL INFORMATION
VOLTAGE PARAMETERS
While voltage is a parameter that will vary from artist to artist, the
Airboat/Airbolt Mini has been tested to operate at a minimum voltage of around
5-Volts with a maximum voltage of 12-Volts. Depending on the type of needle
configuration, or brand you use, feel free to adjust the voltage to obtain the
desired performance.
NOTE: Some machines require a minimum voltage to operate correctly,
please check your machine manufacturer’s requirements.
WARRANTY
Darklab warrants that the device will perform efficiently when used as intended. Should this product prove to be defective due to manufacturing issues, Darklab will repair/replace the device – free of charge. This warranty will be void if the device shows signs of having been tampered with, disassembled, handled roughly, dropped, overexposed to moisture, or damage resulting in compromised functionality.
HANDY TIPS
The following tips will help you get the most out of your AirBolt/Airbolt Mini and avoid potential issues:
- For the Xion, mini does not exceed 10 volts.
- Use only quality cables. A good connection will ensure consistent performance.
- Use only FDA-approved cold sterilization solutions for disinfection.
- NOT AUTOCLAVABLE.
ADDITIONAL INFORMATION
TROUBLESHOOTING
1.- Machine Manufacturer
FK Irons: 1771 NW 79th Avenue, Doral, Florida 33126
2.- Servicing Your Machine
As for any mechanical device, FK Irons strongly suggests that you service
your device once a year to ensure all working parts are working as expected.
This ensures the optimal condition of all working parts including internal
machine clean-up and fresh lubrication. Routine servicing will ensure that
your machine remains functioning from the very first day. Service is subject
to fees.
3.- Warning
Disconnect the machine from any power before making any adjustments. For
service inquiries, please contact [email protected]
For additional tips and tutorials, please visit
Youtube.com/fkirons
Documents / Resources
|
darklab airbolt Machine
Battery
[pdf] User Manual
airbolt, Machine Battery
---|---