PYRAMID 21055A Fly Screen Motorcycle Extenda Fenda Instruction Manual

PYRAMID 21055A Fly Screen Motorcycle Extenda Fenda

Specifications:

• 1 x Hornet Radiator Cheek (LHS)
• 1 x Hornet Radiator Cheek (RHS)
• 1 x Carbon Steel Bracket (LHS)
• 1 x Carbon Steel Bracket (RHS)
• 2 x M5x16mm Flanged-Button Bolt
• 2 x M6x30mm Flanged-Button Bolt
• 2 x M6x12mm Flanged-Button Bolt
• 2 x M6 Serrated-Flanged Hex Nut
• 4 x M6 Bolt Cap
• 2 x M6x12mm Black Nylon Spacer
• 2 x 2mm Foam Pad (40mm Lengths)
• 1 x Red Decal Set (21055C & 21055E)
• 1 x Black & Yellow Decal Set (21055D)
• 1 x Black Decal Set (21055Y)

Product Usage Instructions

Assembly Instructions:

• Begin by placing the foam pad strip (Item 11) on the LHS bracket (Item 3) in the position marked in FIG.3. Ensure the foam pad is slightly placed on the bracket in case it needs to be repositioned or trimmed.
• Continue by removing the two OEM fixings in the marked areas shown in FIG.4 from the LHS of the motorcycle. Take the LHS bracket (Item 3), together with 1 x M5x16mm Bolt (Item 5), and thread the bolt into the marked area ‘1’ shown in FIG.4. Tighten the bolt so that the bracket is parallel with the face of the radiator cheek on the motorcycle. Do not overtighten the bolt as you may wish to adjust this angle slightly to improve the fitment of the Pyramid Radiator Cheek.
• Take the LHS Radiator Cheek (Item 1), along with 1 x M6x30mm bolt (Item 6) and 1 x black nylon spacer (Item 10). Place the spacer on the underside of the lower mounting point of the panel and thread the M6 bolt through and into the area marked ‘2’ shown in FIG.3. Do not tighten at this stage.
• Proceed by taking 1 x M6x12mm bolt (Item 7) and 1 x M6 nut (Item 8) and placing through the upper mounting hole of the panel to secure the bracket. Check the alignment of the Radiator Cheek and make any adjustments by altering the angle of the bracket. Check the support provided by the foam pad by gently pressing in that area. Make any necessary adjustments. Once you are happy with the fitment, firmly press the foam pad and tighten all fixings to sufficient resistance.
• Finally, place 2 x bolt end caps (Item 9) over the bolt heads. Repeat this step for the RHS of the motorcycle.

Please Note: We advise that all fixings are checked periodically.

FAQ:

• Q: Do I need any special tools for assembly?
  A: No special tools are required for assembly, standard tools should be sufficient.

• Q: Can I use these parts on any motorcycle model?
  A: These parts are designed for specific motorcycle models, please refer to the compatibility list before installation.

• Q: How often should I check the fixings?
  A: It is recommended to check all fixings periodically to ensure proper fitment and safety.

21055 Honda CB750 Hornet Radiator Cheeks 2023 > fitting Instructions

Kit Includes

The installation process is replicated on both sides. This consists of the relevant panel and fixing bracket, together with an equal share of the supplied fixings. Please note: LHS denotes the left-hand side from the rider’s point of view and likewise RHS denotes the right-hand side.

Assembly Instructions

• • Begin by placing the foam pad strip (Item 11) on the LHS bracket (Item 3) in the position marked in ‘FIG. 3’. Please ensure the foam pad is lightly placed on the bracket in case it needs to be repositioned or trimmed.
• Continue by removing the two OEM fixings in the marked areas shown in ‘FIG. 4’ from the LHS of the motorcycle. Take the LHS bracket (Item 3), together with 1 x M5x16mm Bolt (Item 5), and thread the bolt into the marked area ‘l’ shown in ‘FIG. 4’. Tighten the bolt so that the bracket is parallel with the face of the radiator cheek on the motorcycle. Please do not overtighten the bolt as you may wish to adjust this angle slightly to improve the fitment of the Pyramid Radiator Cheek.
• Take the LHS Radiator Cheek (Item 1), along with 1 x M6x30mm bolt (Item 6) and 1 x black nylon spacer (Item 10). Place the spacer on the underside of the lower mounting point of the panel and thread the M6 bolt through and into the area marked ‘2’ shown in ‘FIG. 3’. Please do not tighten at this stage.
• Proceed by taking 1 x M6x12mm bolt (Item 7) and 1 x M6 nut (Item 8) and placing through the upper mounting hole of the panel to secure the bracket. Please check the alignment of the Radiator Cheek and make any adjustments by altering the angle of the bracket. Please check the support provided by the foam pad by gently pressing in that area. Make any necessary adjustments. Once you are happy with the fitment, firmly press the foam pad and tighten all fixings to sufficient resistance.
• Finally, place 2 x bolt end caps (Item 9) over the bolt heads. Repeat this step for the RHS of the motorcycle.

Please Note : We advise that all fixings are checked periodically .

Please note: 2 x Item 9 shown in ‘FIG. 2’ is not required with colour options ‘Pearl Glare White’ or ‘Goldfinch Yellow’ but may be used if desired .

Any questions?
sales@pyramidmoto.co.uk
+44 (0)1427 677990
www.pyramidmoto.co.uk
Follow us on social media and feel free to leave us a review!

References

• Pyramid Motorcycle Accessories - Fly Screen Motorcycle, Extenda Fenda

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>