FRONT RUNNER RRAC268 Zamp Solar Panel Kit Mounting Bracket Installation Guide

August 18, 2024
Front Runner

FRONT RUNNER RRAC268 Zamp Solar Panel Kit Mounting Bracket

Product Information

Specifications:

  • Model: RRAC268
  • Brand: Front Runner
  • Compatibility: Zamp Solar Panel Kit
  • Components: Bracket 01, Hex Head Bolts, Flat Washers, Nyloc Nuts, Nut Caps
  • Tools Required: Torque Wrench (13mm)

Product Usage Instructions

Get Organized
Make sure you have all the components listed in the manual and the necessary tools ready.

Fit and Secure

Assemble the Bracket to the Frame

  1. Slide the T-nut into the solar panel frame as per the Zamp Solar Fitment guide.
  2. Loosely assemble the Bracket to the frame using the provided fasteners.
  3. Space the Brackets at 202mm increments and fully tighten.

Mount the Solar Panel

  1. Determine the slats to be used for mounting the Zamp Solar panel.
  2. Slide the Hex Head Bolts into the slats’ pockets.
  3. Secure the assembly from step 2.1 using Hex Head Bolts, Flat Washers, and Nyloc Nuts.
  4. Fully tighten all fasteners with a torque wrench to the specified torque.
  5. Place Nut Caps over all Nyloc Nuts for protection.

Finish
Congratulations on completing the installation! Admire your work and consider adding other vehicle and rack accessories to enhance your setup.

FAQ

What should I do if I have questions about installing the product?
Contact Front Runner for assistance. Failure to install the product correctly may void warranty and cause damage.

IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions. Please call us if you have any questions about the installation of this product.

GET ORGANIZED

IN THE BOX

  1. 4 X Bracket 01 ( 2L & 2R)
  2. 4 X M8 x 16 Hex Head Bolt
  3. 4 X M8 x 16 x 1.6 Flat Washer
  4. 4 X M8 Nyloc Nut
  5. 4 X M8 Nut Cap

TOOLS NEEDED

FIT AND SECURE

  1. Slide the T-nut into the solar panel frame, refer to the Zamp Solar Fitment guide. Loosly assemble the Bracket (Item 1) to the frame using the fasteners supplied with the Zamp Solar Panel Kit. Space the Brackets at 202mm increments and fully tighten.
  2. Determine which slats you will be using to mount your Zamp Solar panel and Slide the M8 x 16 Hex Head Bolts into the machined pockets in the slats. Secure the assembly from 2.1 using M8 x 16 Hex Head Bolts, M8 x 16 x 1.6 Flat Washers and M8 Nyloc Nuts (Item 2, 3 & 4). Fully Tighten.
    Tightening Torque:
    M8 : 15-20Nm / 11.06 ft lb – 14.75 ft lb
    Place M8 Nut Caps (Item 5) over all Nyloc Nuts.

FINISH

Congratulations! You did it. Take a step back and admire your work!

INSTALL OTHER VEHICLE AND RACK ACCESSORIES

Now’s the time to visit your favorite Front Runner Dealer in person or online.

CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Front Runner User Manuals

Related Manuals