Eastbrook 33.0018 Freestanding Bath Installation Guide
- August 17, 2024
- Eastbrook
Table of Contents
Eastbrook 33.0018 Freestanding Bath
Product Information
Specifications:
- Installation: Requires two people
- Important: Do not sit or stand on the bath rim
- Maintenance: Clean with a soft damp cloth, avoid harsh chemicals
- Tools Required: Adjustable Wrench
Product Usage Instructions
Step 1: Receive Your Bath
Ensure the bath is on a soft surface to protect against scratches. Place
the bars onto the bath, along with the washers and nuts without tightening.
Step 2: Installation
Position the feet onto the bars and secure using the provided nuts and
bolts. Adjust the position of the feet to align with the bath. Tighten all
nuts to secure the feet and bars to the bath.
Maintenance & Cleaning:
Clean marks on the surface with a soft damp cloth. For stubborn marks, use
toothpaste and rinse thoroughly. Avoid harsh chemicals or abrasive materials.
Test colored oils/creams on a small area before use.
Warning:
If the bath has a tap deck, drill tap holes according to your needs.
Silicone the tap holes after drilling to prevent water leakage at the faucet.
Technical Helpline:
Phone: 01452 317890
Email: technical@eastbrookco.com
Address: Eastbrook Road, Gloucester GL4 3DB
Frequently Asked Questions (FAQ):
-
Q: Can I sit or stand on the bath rim?
A: No, the freestanding bath is not designed to take weight on the rim. Avoid sitting or standing on it. -
Q: How should I clean stubborn marks on the bath surface?
A: Use toothpaste on a soft damp cloth for stubborn marks, then rinse thoroughly. Avoid harsh cleaning chemicals.
Image for installation purpose only
Please retain this manual after installation for future reference and
maintenance
Product must be installed in compliance with relevant Water Bylaws
Receive Your Bath
Unpack and check for damage.
After receiving your bath, please unpack and remove all packaging, checking
for damage, damage reported after painting will not be covered.
Repack the bath if it is not being immediately installed.
Metal bars required for feet installation are attached to the underside of the
bath.
Protect your bath.
Before commencing installation, ensure the bath is completely protected, leave
covering in place until the bathroom is complete. Scratches and damage
incurred during installation are not covered by the warranty.
Important information
- Two people are required for installation.
- Please read these instructions thoroughly and retain for future reference
- Always check for pipes and cables before drilling
- Freestanding bath is not designed to take weight on the rim, Do not sit or stand on the bath rim.
- Bath feet and waste are supplied separately.
Parts List
TOOLS REQUIRED
Installation
Step 1
- Ensure the bath is on a soft surface to protect against scratches.
- Place the bars onto the bath, along with the washers and nuts as shown below, do not tighten at this stage to allow for adjustment, taking care not to damage the bath surface.
Step 2
- Position the feet onto the bars and secure using the nuts and bolts provided.
- Adjust the position of the feet to align with the bath.
- Tighten all of the nuts so that the feet are secured to the bar and the bars are secured to the bath.
Option A – with 4 bars
Troubleshooting
- Movement in the feet after assembly
Please check the feet are assembled properly, make sure fastener washers and washers are placed correctly.
Maintenance & Cleaning
- Marks on the surface of the bath, should be cleaned using a soft damp cloth, for more stubborn marks, toothpaste can be applied and then rinsed thoroughly.
- No harsh cleaning chemicals or abrasive materials can be used on any surface.
- If using coloured oils/creams, carry out a test on small area prior to use to ensure that these will not cause staining.
- Never pour coloured oils/creams directly into an empty bath, always apply them into the bath water.
Warning
Pay attention to below points if the bath is designed with tap deck.
- The tap holes are not pre-drilled on the deck, drill holes according to your need.
- Check and silicone the tap holes to make sure they are solid after drilling.
- Check and make sure that there is no water leakage at the faucet.
Illustrations below are for reference only
Technical Helpline: 01452 317890
Email: technical@eastbrookco.com
Eastbrook Road, Gloucester GL4 3DB
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>