Eastbrook VIN V Freestanding Bath Installation Guide
- August 17, 2024
- Eastbrook
Table of Contents
Eastbrook VIN V Freestanding Bath
Product Specifications:
- Product Name: Freestanding Bath Including Waste
- Brand: VIN V FASHION BATHROOM LIFE
- Material: Flexible
Product Usage Instructions
Important Note:
! Warning (apply to bath pre-fitted with waste)
The pre-fitted waste has NOT yet been fully installed. Please use a qualified installer to secure it to the bath to avoid any water leaking. Before use, please test the bath to ensure the waste has been properly installed.
Maintenance & Instruction:
For proper maintenance of the freestanding bath including waste, follow these instructions:
- Regularly clean the bath with a mild detergent and water solution.
- Avoid using abrasive cleaners or materials that may damage the surface of the bath.
- Inspect the waste fittings periodically to ensure they are\ secure and not leaking.
Illustration:
Refer to the product manual for detailed illustrations on how to properly install and maintain the freestanding bath including waste.
Technical Support:
If you require technical assistance, contact our Technical Helpline at 01452 317890 or email us at technical@eastbrookco.com. Visit us at Eastbrook Road, Gloucester GL4 3DB.
FAQ
- Q: What should I do if I notice water leaking from the waste?
- A: If you notice water leaking from the waste, immediately stop \using the bath and contact a qualified installer to inspect and repair the waste fittings.
- Q: Can I use strong chemicals to clean the freestanding bath?
- A: No, it is recommended to use a mild detergent and water solution for cleaning to avoid damaging the surface of the bath.
Please retain this manual after installation for future reference and maintenance
The product must be installed in compliance with relevant Water Bylaws
IMPORTANT:
- Two people are required for the installation
- A freestanding bath is not designed to take weight on the rim.
- Do not sit or stand on the bath rim
TOOLS REQUIRED FOR INSTALLATION
Installation
Step 1
Adjust the bath feet until the bath base is 3mm above the floor; This can be done by turning the feet bars accordingly and then use a wrench to tighten the nuts on the bars
Step 2
Mark the floor with the outline of the bath, at the final installation position with the marking pencil
Step 3
Carefully tilt bath on its side and use flexible connector to connect waste outlet to the trap as illustrated on figure 2
*** Flexible connector and waste trap are not supplied
Step 4
Position bath on the floor marking as marked on step 2, make sure that flexible connector is not kinked upward on installation as this will result in drainage issue
Important Note:
- A) Water test your bath prior to silicone to ensure it drains correctly as no claims for non-draining baths will be valid after enclosing or tiling has been done
- B) Water test overflow pipe and waste to ensure they are not leaking
Step 5
Apply silicone around the base surrounding of the bath, see figure 3
*** Do not use within 24 hours to let the silicone fully cure
Cleaning & Maintenance
- A) To preserve the polished surface, after using your bath, clean with soft cloth and warm soapy water to wash away any body oils or soap residue that forms a ring tide mark
- B) Do not use powders, pastes, crème cleaners, thinners, window cleaning sprays or dry cleaning liquid, etc.
- C) Stubborn marks or fine scratches may be polished out with Brasso
- D) When coloured essential oils are used, first test that the colour won’t stain your bath. Always add oils into a bath full of water. Never pour them into a empty bath
RECEIVING YOUR BATH
- A) Unpack and check for damage.
- After receiving your bath, please unpack and remove all covering, checking whether there is any damages. Repack the bath if it is not being immediately installed.
- B) Protect your bath.
- Before commencing installation, ensure the bath is completely protected Scratches and cracks incurred during installation are not covered by the warranty
REPAIRS
Scratches can be improved with 1200-grade wet and dry sandpaper and then repolished with Brasso polishing compound. Always polish scratch in a circular movement
! Warning (apply to bath pre-fitted with waste) The pre-fitted waste has NOT yet been fully installed. Please use a qualified installer to secure it to the bath to avoid any water leaking. Before use, please test the bath to ensure the waste has been properly installed.
- Technical Helpline: 01452 317890
- Email: technical@eastbrookco.com
- Eastbrook Road, Gloucester GL4 3DB
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>