HYUNDAI J9F18 AU000 Cargo Blocks Installation Guide

August 14, 2024
HYUNDAI

HYUNDAI J9F18 AU000 Cargo Blocks

Specifications:

  • Vehicle Model: Multiple
  • Accessory: Cargo Blocks
  • Part Numbers: J9F18 AU000 (DIO), J9F18 AU600 (PIO)
  • Language: English
  • Part Weight: 0.40 lbs (0.18 kg)

Product Usage Instructions

Electronic Installation Instructions:

If you have a printed copy of the installation instructions, ensure you have the latest revision by scanning the QR code orvisiting the website provided before starting the installation.

Application Notes:

This product is designed for use on carpeted surfaces. Refer to the application chart on Page 3 for more details.

Basic Required Tools:

No tools are required for the installation of this accessory.

Kit Overview:

No. Qty Description
1 4 Cargo Block
2 1 Quick Reference Guide*

*Note: Quick Reference Guide is not included in PIO kit.

New Vehicle Installation Steps:

  1. Open the rear hatch.
  2. Remove the Cargo Blocks from the packaging.
  3. Place Cargo Blocks on the floor in a one (1) foot square formation with bottoms facing each other.

Customer Installation Steps:

  1. Open the rear hatch.
  2. This product is for use on carpeted surfaces only.
  3. Place Cargo Block(s) on the vehicle floor hook side down around the cargo to be restrained, ensuring proper weight distribution on the block face.
  4. Position the Cargo Block(s) securely against the cargo.

Important: Unstable cargo could lead to imbalanced driving. Ensure cargo weight does not exceed 15 lbs and is positioned with the center of gravity low to the ground for stability.
To move Cargo Block(s), lift vertically until disengaged from the floor, then reposition as needed.

Frequently Asked Questions (FAQ):

  • Q: Can these Cargo Blocks be used on any type of surface?
    A: No, these Cargo Blocks are intended for use on carpeted surfaces only. Use on other surfaces may result in instability.

  • Q: What is the maximum weight that can be restrained by these Cargo Blocks?
    A: The maximum recommended weight is 15 lbs. Exceeding this weight may compromise stability during driving.

Electronic Installation Instructions

if this is a printed copy of the installation instructions, ensure you have the latest revision by scanning the QR code or by entering the website address listed below before beginning installation. Use the latest revision date as noted by “Rev. Date” above.
www.hyundaiaccessories.com/admin_media_uploads/installationSheets/j9f18_au000.pdf

Application Notes

Instructional Symbols / Definitions

  • Denotes warnings that may lead to serious physical injury or vehicle damage
  • Denotes cautions to be taken to avoid physical injury or electronic component damage
  • Denotes cautions to be taken to avoid vehicle and component damage
  • Denotes quality processes to be checked prior to moving to the next step
  • Denotes specific tools that are necessary to complete a step
  • Denotes important information to be reviewed during the step
  • Denotes personal protective equipment (PPEs) that may be required for a step. Examples of safety equipment icons noted below:

Basic Required Tools

Part Weight (Gross)

FMVSS 110 Compliance Information

All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories.
Load Label Part Number: NP070 – 09003

Notes to the Installer:

  1. Read the entire Installation Instructions prior to beginning the installation of this accessory.
  2. If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the removal of the old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused.
  3. Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
  4. Ensure the vehicle is properly protected in the area(s) that the accessory is to be installed.
  5. NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
  6. Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.

Kit Overview

  • Note : Item 2 is not included in PIO kit

VEHICLE INSTALLATION

NEW VEHICLE INSTALLATION, PLEASE FOLLOW STEPS BELOW

  • A. Open the rear hatch.
    B. Remove the Cargo Blocks from the packaging.

  • A. Place Cargo Blocks on the floor in the shape of a one (1) foot square, with bottoms facing each other as shown. This is the recommended position for demonstrating this accessory.

FOR CUSTOMERS, PLEASE FOLLOW STEPS BELOW OR REFER TO THE QUICK REFERENCE GUIDE

  • A. Open the rear hatch.

  • B. This product is intended for use on carpeted surfaces only.

  • C. Place Cargo Block(s) on vehicle floor hook side down surrounding the cargo to be restrained. Ensure the weight of the item is on the block face. NOTE: Insufficient weight on the block face may result in unstable Cargo Block(s).

  • D. Ensure the Cargo Block(s) are properly positioned against the cargo.
    WARNING : Unstable cargo could become unbalanced during driving. Place cargo in the most stable position before driving. Cargo is most secure when its weight (Max 15 lbs) and center of gravity are lowest to the ground.

  • A. To move Cargo Block(s), lift up vertically until block has disengaged with the floor, then reposition.
    WARNING : Cargo Blocks(s) will not restrain cargo during heavy braking or accident. Unrestrained cargo can cause injury.

Visual Check

  • Item to be Checked
    • Cargo Blocks are stable and seated on the floor surrounding the item.
  • Result
    • Cargo Blocks are in place.

Care & Cleaning

Cleaning Instructions for:

  • Multiple Cargo Blocks

The Cargo Blocks can be wiped, swept, lightly vacuumed, cleaned with water, or soap and water. Do not use petroleum-based solvents for cleaning. Ensure the Cargo Blocks are completely dry before placing them in the vehicle.

Application Chart

    • Carpet side facing up only
  • Applicable
  • – Not Available

Vehicle Model: Multiple

  • Model Year Multiple
  • Part No. J9F18 AU000 (DIO)
  • J9F18 AU600 (PIO)
  • Language English
  • Rev. Date 1/16/20243

Accessory: Cargo Blocks
Difficulty : (A)
Note : Difficulty stated above reflects the minimum level of expertise required to install the accessory:

  • (A) Customer
  • (B) Dealer Technician
  • (C) Master Technician or Specialist

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals