GE APPLIANCES PVW1030, PVW1036 30 and 36 Inch Vent Hood Installation Guide

: August 14, 2024
: GE Appliances

Table of Contents

PVW1030, PVW1036 30 and 36 Inch Vent Hood
Safety Information
Installation Preparation
Installation
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Installation Instructions
30” and 36” Vent Hood
PVW1030, PVW1036

PVW1030, PVW1036 30 and 36 Inch Vent Hood

If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com
BEFORE YOU BEGIN
Read these instructions carefully and completely.

IMPORTANT – Save these instructions for local inspector’s use.
IMPORTANT – Observe all governing codes and ordinances.
Note to Installer – Be sure to leave these instructions with Consumer.
Note to Consumer – Keep these instructions for future reference.
Skill level – Installation of this appliance requires a qualified installer or electrician.
Completion time – Approximately 1 to 3 hours
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered under Warranty.

CAUTION
Due to the weight and size of these vent hoods and to reduce the risk of personal injury or damage to the product, TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
WARNING
To reduce the risk of fire or electrical shock, do not use this range hood with any external solidstate speed control device. Any such alteration from original factory wiring could result in damage to the unit and/or create an electrical safety hazard.
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
A. Use this unit only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.
B. Before servicing or cleaning the unit, switch the power off at the service panel and lock the service disconnecting means to prevent the power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,such as a tag, to the service panel.
CAUTION
FOR GENERAL VENTILATING USE ONLY. DO NOT USE TO EXHAUST HAZARDOUS MATERIALS, EXPLOSIVE MATERIALS OR VAPORS.

Safety Information

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back-drafting. Follow the heating equipment manufacturer’s guidelines and safety standards, such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities. When applicable, install any makeup (replacement) air system in accordance with local building code requirements. Visit GEAppliances.com for available makeup air solutions.
When cutting or drilling into walls or ceilings, do not damage electrical wiring and other hidden utilities.
Ducted systems must always be vented to the outdoors.
Local codes vary. Installation of electrical connections and grounding must comply with applicable codes. In the absence of local codes, the vent should be installed in accordance with National Electrical Code ANSI/NFPA 70-1990 or latest edition.

CAUTION
To reduce risk of fire and to properly exhaust air, be sure to duct air outside—do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.
PRODUCT DIMENSIONS AND CLEARANCES
The vent hood must be installed 24″ minimum, and 30″ maximum above the cooking surface.
NOTE: Installation height should be measured from the cooking surface to the lowest part of the hood.
PX8DC1SWSS Duct Cover Accessory
This accessory is available for installations with ceiling heights above 9’ to 10’ and higher. See the table on page 8.
The duct cover accessory must be on-site with the hood at the time of installation.
READ AND SAVE THESE INSTRUCTIONS

Installation Preparation

DUCTWORK PLANNING

This hood is designed to be vented vertically through the ceiling. Use locally supplied elbows to vent horizontally through the rear wall.
Determine the exact location of the vent hood.
Plan the route for venting exhaust to the outdoors.
Use the shortest and straightest duct route possible.
For satisfactory performance, duct run should not exceed 150′ equivalent length for any duct configurations.
Refer to “Duct Fittings” chart to compute the maximum permissible length for duct runs to the outdoors.
Use rigid metal ductwork only.
This vent hood must use a 8” round duct.
Install the house duct to run horizontally between ceiling joists or straight up through the roof.
Install a wall or roof cap with damper at the exterior opening. Order the wall or roof cap and any transition and length of duct needed in advance.
When applicable, install any makeup (replacement) air system in accordance with local building code requirements. Visit GEAppliances.com for available makeup air solutions.

WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY RIGID METAL DUCTWORK.
WALL FRAMING FOR ADEQUATE SUPPORT

This vent hood is heavy. Adequate structural support must be provided. The hood must be secured to a vertical stud in the wall. See page 9 or 14.
We strongly recommend that the vent hood with duct cover be on site before final framing and wall finishing. This will also help to accurately locate the ductwork and electrical service.
Installation will be easier if the vent hood is installed before the cooktop and countertop are installed.

ADVANCE PLANNING
A duct cover accessory may be required for your hood installation depending on ceiling height.
POWER SUPPLY
IMPORTANT – (Please read carefully)
WARNING
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning installation.
Do not use an extension cord or adapter plug with this appliance. Follow National Electrical Code or prevailing local codes and ordinances.
Electrical supply
This vent hood must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15- or 20-amp circuit breaker or time-delay fuse.

Wiring must be 2-wire with ground.
If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.
Route house wiring as close to the installation location as possible. Wiring can enter from the ceiling or rear wall. Route additional length from the ceiling or wall to reach the junction box.
Connect the wiring to the house wiring in accordance with local codes.

Grounding instructions
The grounding conductor must be connected to a ground metal, permanent wiring system, or an equipment-grounding terminal or lead on the hood.
WARNING
The improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded.
TOOLS AND MATERIALS REQUIRED (Not Supplied)

REMOVE THE PACKAGING
CAUTION
Wear gloves to protect against sharp edges.

Remove the duct cover, parts box and foam packaging.
Lift the hood out of the box.
Remove and properly discard the plastic wrapping.
Remove metal grease filters and side bar packaging.
Remove junction box cover.
Remove knockout from junction box.
Install strain relief onto junction box.

CHECK INSTALLATION HARDWARE
Locate the hardware accessory box packed with the hood and check contents.

NOTE: Additional tools, materials and hardware are required to construct your wall framing support.

DETERMINE INSTALLATION HEIGHT

A 10’ ceiling height telescopic duct cover accessory is included to conceal the ductwork running to the ceiling. 8’, 12’, or 14’ ceiling heights can be accommodated with the optional accessories.
This hood can be installed for vented or recirculating (36” width model only) operation.

NOTE: Installation height should be measured from the cooking surface to the bottom of the hood.
The vent hood must be installed above the cooking surface 24″ min to 30″ max for electric and 30” min to 36” max for gas. The hood installation height, from the cooking surface to the bottom of the hood, also depends upon ceiling height and duct cover limitations

DETERMINE HOOD, DUCTWORK AND WIRING LOCATIONS

This hood can be installed onto the wall or underneath the soffit.
For installing the hood to soffit, refer to page 12 for alternate mounting method.
Measure desired distance from the bottom of the hood to the cooking surface, 24” minimum over electric range or 30” minimum over gas range and 36” recommended maximum.
Use a level to draw the cooktop centerline location.
Measure 8” up from the horizontal line indicating the bottom of the hood. Draw another horizontal line to indicate the bottom of the installation bar.
Use a level to draw the cooktop or range centeline location.

For Ceiling Ducting:

If venting out the ceiling, extend the centerline forward on the ceiling to the back wall.
– Measure 6-1/4” from back wall to mark center point.
– Cut 8” dia. duct hole from center point on the ceiling.

Venting Through a Soffit:

Follow the same procedure for ceiling ducting to cut the hole through the top of the soffit.

House Wiring Location:

The junction box is located inside the hood body on the left side. See Illustrations for hood knockout locations.
House wiring may enter the junction box from the rear or the top of the hood on the left side.

To route house wiring through the ceiling or soffit:

The wiring can be routed through a knockout on the back right or front center.

To route house wiring through the wall:

Measure 4” from the bottom of the hood and mark location
Cut a hole approximately 1-1/4” dia. at the marked location at a distance 7-7/8” to the right of the centerline based on table below.
Remove top or rear knockout depending on your installation.

Installation

INSTALL HOOD SUPPORT
IMPORTANT: Framing must be capable of supporting 100 lbs.
1. Locate a minimum of 1 vertical stud for the installation bar by tapping drywall with a hammer or use a stud finder.
2. Level the installation bar and center left to right above the marked line. Hold bar against the wall. 3. Drill 1/8” pilot holes at the 1 vertical stud locations through holes in the installation bracket. Secure the installation bar with supplied screws (A) as shown above.

Drill Bottom Mounting Hole Locations:

Hang hood on installation bar to mark anchor locations. Mark hole locations through the back of the hood.
If installing to the cabinet, hold the hood flush to the cabinet to mark screw hole locations
Remove the hood and drill 5/16” clearance holes centered at the marks you made.
INSTALL HOOD SUPPORT (Cont.)
• Install wall anchors (C) by tapping the anchors with a hammer to seat the teeth of the flanges into the wall. This keeps anchor from rotating.
• Drive the anchor screws until the barrels crimp against the inside of the wall.
• Remove the screws from the wall anchors before installing the hood.
INSTALL DAMPER
IMPORTANT: Remove shipping tape from damper and check that damper moves freely.
Install Top Damper:
• Install the top damper to the hood body as shown in Figure A using screws (B) from top of hood.
INSTALL HOOD ONTO WALL
CAUTION 2 people are required to lift and position the hood onto the mounting bracket.
• Pull house wiring through knockout at the back or top of the hood.
• Lift the hood and place over the hooks on the installation bar. Allow the hood to slide down into position.
• Check to be sure the hood is level and centered.
• Tighten wall anchor screws (C) to finish hood body installation to the wall.
• Remove cover from junction box inside the hood.
CONNECT ELECTRICAL
Verify that power is turned off at the source.
WARNING
If house wiring is not 2-wire witha ground wire, a ground must be provided by theinstaller. When house wiring is aluminum, be sureto use UL approved anti- oxidant compound and aluminum-to-copper connectors.
1. Remove junction box cover. 2. Pull the house wiring through the knockout at the top or back of the hood and secure with the strain relief. 3. Use UL listed wire nuts to connect incoming white to white, and black to black wires.
4. Loosen the green grounding screw (with grounding bracket) in the junction box. Loop solid copper house wire clockwise around the green grounding screw and above the bracket. Firmly tighten the screw over the loop. 5. Replace junction box cover and ensure wires are not pinched.
NOTE: For corded installation:
Use only with rangehood cord-connection kits that have been investigated and found acceptable for use with this model rangehood.
INSTALL RECIRCULATION BOX (IF APPLICABLE)
1. Install the top bracket where the upper portion of the cover stops using the provided anchors and wood screws, aligning the center notch with the existing drawn centerline. Make sure the bracket is level. 2. Using the tabs of the bracket, install the recirculation box on the tabs
CONNECT DUCTWORK
1. Connect duct from the bottom of the recirculation box or connect the vented house ducting to the top of the damper as shown.
2. Seal all connections with duct tape. CAUTION
Do not use sheet metal screws at the transition to ductwork connection. Doing so will prevent proper damper operations. Seal connection with tape only.
INSTALL DUCT COVERS
NOTES: Each duct cover bracket is 1.575” wide and has a notch at the center. The purpose of the slots is intended to allow one to use a stud if available along with a wall anchor.
1. Install the top bracket where the upper portion of the cover stops using the provided anchors and wood screws, aligning the center notch with the existing drawn centerline. Make sure the bracket is level.
2. Depending on what length of duct cover is used, draw a level horizontal line located at the bottom of the top cover. (See page 7 for the upper cover height.) Align the bottom edge of the lower bracket with the line and the center notch with the centerline and mount the bracket with the screws and anchors.
3. Orient the upper duct cover based on the respective venting configuration (louvers up for recirculate and down for vented). Secure the upper cover to the brackets with the provided machine screws.
4. Install the lower cover by wrapping it around the lower cover and then securing it with six machine screws from underneath the top of the hood to the bottom flange.
INSTALL BLOWER
NOTES: The blower has four through holes for securing by machine screws to the hood body; two of which are key holes.
1. For the 30”, the center decorative trim piece will need to be removed.
2. Noting which holes are key holes, pre-install the relevant screws to the body.
3. Install the blower by inserting and sliding the keyholes over the screws.
4. Install the remaining screws through the regular holes of the blower to the hood body.
5. Tighten all screws.
6. Install the blower wire harness connector to the control box connector.
7. For the 30” reinstall the decorative trim piece.
INSTALL GREASE FILTERS
1. Remove protective film.
2. Insert the two back tabs of each filter into the back edge of the hood body.
3. Push the button on the latch to open the latch.
4. Install the front edge of the filter into the front edge of the hood body.
5. Release the latch, making sure it is fully engaged
by hearing a click of the latch and the button is fully released.

Charcoal Filter (for recirculation installation only)
NOTE: DO NOT rinse, or put charcoal filter in an automatic dishwasher.
The charcoal filter is NOT included with the unit. Order charcoal filter UXCF91. It cannot be cleaned; it must be replaced. It is recommended that the charcoal filter be replaced every 6 months or if it is noticeably dirty or discolored.
To reduce the risk of fire and shock, when used in recirculation mode, use only charcoal filter UXCF91.
To inquire about purchasing replacement charcoal filters or to find the location of a dealer nearest you, please call our toll-free number:
National Parts Center 800.626.2002
To Install

Remove the grease filters. See Filters section.
Install the charcoal filter mounts to either side of the motor using three screws per side.
Insert the tab on the charcoal filter into the triangular slot on the mount.
Clip the charcoal filter in until it is locked
Repeat with second filter on the other side of the motor.
Reattach the metal filters. See Filters section.

To Remove

Remove grease filters-See Filters section
Unclip the charcoal filter by pressing the release clip.
Carefully remove charcoal filter from tab.

MAKE UP AIR TECHNOLOGY
This operation must be performed by a qualified technician or installer.
Note to Installers and Inspectors: This product comes equipped with a simple installation feature that limits maximum CFM levels in order to comply with certain local codes or regulations. This installation method may not be necessary for all installations, please refer to your local codes for further guidelines.
This makeup air feature applies to single motor models only.
CAUTION
Hood must be disconnected from main power prior performing the conversion instructions listed below. Failure to do so could result in personal injury or damage to the product.
To modify unit (if needed for local codes): 390CFM
By design, the maximum blower speed is greater than 400 CFM. For local codes requiring reduced CFM, modify the wiring as described below:

Remove the Baffle filters.
Disconnect all the harnesses from the top of control box on right side of motor
Loosen the screws on top of control box and slide out to remove it from the hood
Uninstall the control box cover
For a maximum of 390 CFM Unit can operate with 4 speeds (Low, Medium, High, Boost).
i. Disconnect connectors of the BROWN wire.
ii. Remove the cap attached to the connector of the RED wire.
iii. Connect the mating connector of the BROWN wire and the RED wire.
iv. Attach the cap to the open BROWN wire connector.
Reinstall control box cover and secure control box to the bracket in the hood using the two screws
Connect all harnesses on top of the control box
Reinstall filters.