cleverio SD110 Wireless Kinetic Doorbell Kit User Guide

August 13, 2024
Cleverio

cleverio SD110 Wireless Kinetic Doorbell Kit

Product Usage Instructions

Push Button

  1. Open the back of the push button using a screwdriver.
  2. Push the bracket downwards to separate it from the push button.
  3. The push button is powered by kinetic energy stored with each press. Press multiple times if unused for a long period.

Chime Pairing

  1. Connect the chime to a wall socket.
  2. Press the push button within 2 minutes of installing the batteries into the chime to pair them.
  3. To pair multiple chimes/buttons, follow the specified steps.

Chime Settings

  • Press to turn the nightlight on/off.
  • Press multiple times to change the melody (36 melodies available).
  • Press multiple times to set the volume.
  • Press the button on the front of the chime to enable/disable sound and/or flashing light.

Mounting Instructions

  1. Use double-sided adhesive tape for smooth indoor surfaces or screws and plugs for outdoor mounting.
  2. To mount using adhesive tape, peel off the protective sides, attach it to the bracket, and press onto the surface.
  3. To mount with screws and plugs, drill holes, insert plugs, attach the bracket with screws, and slide the push button onto the bracket until it clicks.

Detaching and Resetting

  • To detach the push button, use a screwdriver.
  • To reset, hold the melody selection button on the chime for 20 seconds until a sound is emitted to remove pairing.

Use

Push button

  • Open the back of the push button using a screwdriver (1). Push the bracket downwards to separate it from the push button (2).
  • The push button is powered by kinetic energy which is stored each time the button is pressed. If the button hasn’t been pressed for a long time, you may need to press the button multiple times in quick succession to charge it.

Chime

  1. Connect the chime to a wall socket.
  2. The chime emits a sound to indicate it’s ready for pairing.
  3. Press the push button within 2 minutes of installing the batteries into the chime to pair the units together. The chime emits a sound to confirm the pairing was successful.
  • To pair multiple chimes to the same button, repeat the steps above.
  • To pair multiple buttons to the same chime, disconnect the chime each time you pair a new button.
  • If the chime does not emit a sound during stage 2, press any button on the chime when it is disconnected from power to remove any residual power, wait a short moment, and attempt to pair again.
  • Note! A chime can be paired with multiple push buttons, as each chime supports up to 8 memory slots. If an additional push button is paired after this, the earliest paired button is automatically disconnected.
  • A push button can control up to 50 chimes total.

Chime settings

  • a. Press to turn the nightlight on/off.
  • b. Press multiple times to change the preferred melody (36 melodies).
  • c. Press multiple times to set the volume.
  • d. Press the button on the front of the chime to enable/disable sound and/ or the flashing light when the push button is pressed in the following order: flash, sound, flash + sound.

Mounting the push button bracket

  • The push button bracket can be mounted to a surface using the included double-sided adhesive tape or screws and plugs (not included).
  • The adhesive tape is recommended for a smooth surface that is protected from weather. Screws and plugs are recommended for outdoor mounting.

Double-sided adhesive tape

  • Peel off both protective sides on the tape and attach it to the bracket. Press the bracket and tape onto the surface.
  • Press (1) and slide (2) the push button onto the bracket until you hear a click to mount it.

Screws and plugs (not included)

  • Drill two holes into the mounting surface using an electric drill. Insert plastic plugs into the hole and attach the bracket using the screws.
  • Press (1) and slide (2) the push button onto the bracket until you hear a click to mount it.

Detaching the push button

  • If you need to remove the push button from a mounted position you can detach it from the bracket using a screwdriver.

Resetting

Press and hold the melody selection button (c) on the chime for 20 seconds until a sound is emitted to remove the pairing between the chime and button.

Troubleshooting

  • I’m having trouble pairing the chime to the push button.
  • Make sure the push button has enough kinetic energy by pressing it in quick succession multiple times to charge it. Make sure the chime is connected to a working 230 V wall outlet.
  • Make sure the push button and chime are not too far apart (up to 100 m) and have no obstacles in the signal path. Place the chime close to the push button and try again.
  • Avoid installing the push button on a metal door frame.
  • Re-initiate the pairing procedure, and make sure to follow the instructions in the same order they are described in the manual.

Safety information

  • The chime is intended for use in temperatures from 0-35 °C and not for outdoor use. Only for use in dry areas. The push button can be mounted outdoors, but we recommend you mount it in a place where it’s shielded from wind and rain.
  • Do not open or modify the devices in any way, this should only be carried out by a qualified technician.
  • The range of 100 meters can vary due to concrete walls, and electrical or electro-magnetic sources that can interfere with the signal.
  • If the push button doesn’t react when you press it, press it multiple times to charge it using kinetic energy.

Simplified EU Declaration of Conformity

  • Kjell & Company hereby declares that this device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU. Full text of the EU declaration of conformity is available at www.kjell.com/66289

Specifications

  • Frequency: 433.92 MHz
  • Range: Up to 100 meters
  • Size: Push button: 90x40x26 mm
  • Chime: 83x83x32 mm
  • Included: Push button (transmitter), chime (receiver), adhesive tape, manual
  • Wireless frequency: 433.050–434.790 MHz
  • Effective Radiated Power: <20 mW
  • www.cleverio.se
  • Box 50435 Malmö
  • Sweden
  • 2024-08-05

Documents / Resources

| cleverio SD110 Wireless Kinetic Doorbell Kit [pdf] User Guide
SD110, SD110 Wireless Kinetic Doorbell Kit, Wireless Kinetic Doorbell Kit, Kinetic Doorbell Kit, Doorbell Kit, Kit
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals