FORTIN EVO-ONE TOYOTA Hybrid H-Key Installation Guide

: August 11, 2024
: FORTIN

Table of Contents

FORTIN EVO-ONE TOYOTA Hybrid H-Key
REGULAR INSTALLATION
CONFIG.1 DESCRIPTION
CONFIG.1 WIRING CONNECTION
CONFIG.2 DESCRIPTION
DCRYPTOR PROGRAMMING PROCEDURE
REMOTE STARTER FUNCTIONALITY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FORTIN EVO-ONE TOYOTA Hybrid H-Key

REGULAR INSTALLATION

Vehicle functions supported in this diagram (functional if equipped)

VEHICLE

| YEARS|

Configuration

|

Immobilizer bypass Contournement d’immolisateur

2022

| 2023-2024| 1| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •
| Hybrid H-Key Before November 2022| 2023| 2| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •| •

CONFIG.1 DESCRIPTION

BUILD BEFORE NOVEMBER 2022

CONFIG.1 WIRING CONNECTION

CONFIG.2 DESCRIPTION

DCRYPTOR PROGRAMMING PROCEDURE

Parts required (not included)

1x FLASH LINK UPDATER,
1x FLASH LINK MANAGER
1x Microsoft Windows Computer with Internet connection
Ordinateur Microsoft Windows avec connection Internet

Press and hold the programming button: Connect the 6-PIN Main harness (White connector).
The LEDs will alternate between BLUE, RED,YELLOW & BLUE/RED flashes.
Release the programming button when the LED is BLUE.
If the BLUE LED is not ON solid disconnect the 6-Pin Main connector and go back to step 1.
Insert the required remaining connectors.
Turn the key to the Ignition ON/RUN position.
The BLUE LED will flash rapidly.
Wait , The BLUE LED will turn ON solid.
Start the vehicle.
The BLUE LED will turn OFF.
The RED LED will turn ON.
Turn the key to the OFF position.
Remove the key from the ignition switch.
Start the vehicle.
The RED LED will turn OFF.
The YELLOW LED will turn ON.
Wait , The RED and YELLOW LEDs will alternate.
Turn the key to the OFF position.
Disconnect all connectors and after the 6-Pin (Main-Harness) or the 4-Pin Data-link connector.
Use the tool:
FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
*Parts required (not included)
AFTER DCRYPTOR PROGRAMMING COMPLETED Go back to the vehicle and reconnect the 6-Pin (Main-Harness) or the 4-pins (Data-Link) connector and after all the remaining connector.

REMOTE STARTER PROGRAMMING PROCEDURE
REFER TO THE QUICK INSTALL GUIDE INCLUDED WITH THE MODULE FOR THE REMOTE STARTER PROGRAMMING.

REMOTE STARTER FUNCTIONALITY

Notice : Updated Firmware and Installation Guides Updated ﬁrmware and installation guides are posted on our website on a regular basis. We recommend that you update this module to the latest ﬁ rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualiﬁed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

www.fortinbypass.com