MAJESTIC WT 249 LCD Weather Station with Projection Instruction Manual

: June 6, 2024
: Majestic

Table of Contents

FAONT VIEW
TOP VIEW
BACK VIEW
QUICK SETUP
TO INSTALL THE OUTDOOR TRANSMITTER
TO SET THE WEATHER STATION
TO SET ALARM 1 AND 2
TO TURN ON OR OFF YOUR DAILY ALARM
TO USE SNOOZE ALARM
TO USE THE HI-LO DIMMER
- TO DISPLAY TEMPERATURE IN DEGREE °C OR °F
- TO USE THE PROJECTION (operated by adaptor only)
WEATHER FORECAST INDICATOR
IF YOU LOSE THE OUTDOOR TEMPERATURE AND HUMIDITY
LOW BATTERY INDICATION OF YOUR OUTDOOR TRANSMITTER
CARE OF YOUR WEATHER STATION CLOCK
SPECIFICATIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MAJESTIC WT 249 LCD Weather Station with Projection

FAONT VIEW

TOP VIEW

BACK VIEW

MAJESTIC-WT-249-LCD-Weather-Station-with-Projection-
Overview

QUICK SETUP

STEP 1:
Plug in the enclosed AC/DC adaptor to an AC wall outlet and then the DC jack to the back of your weather station.

STEP 2:
Keep your weather station and wireless outdoor transmitter next to each other. Slide open the battery cover at the back of your wireless outdoor transmitter, then insert 2 x AAA new alkaline batteries to the battery compartment. Make sure the Channel selector switch is at 1 position. Replace the battery cover. Your weather station will receive data signal from the outdoor transmitter in few seconds. Then place your outdoor transmitter in a dry and shaded area.

STEP 3:
The weather station computes weather forecasts based on changes in pressure sensor. However, when using the weather station for the first time, it may take up to a few days of collecting sufficient information for more accurate forecasts. Manual setting of the weather forecast can slightly accelerate this process.

Please refer to “ TO SET THE WEATHER STATION ” Step 9″.

TO POWER UP THE CLOCK
Plug in the AC/DC adaptor to an AC household outlet, and then plug the DC jack to the lower right back of the unit. Your unit is ready to work for you.

TO INSTALL BACKUP BATTERIES
Your weather station requires 2 x new AA batteries (not included) to provide backup power to it in the event of a temporary power interruption.

Place your weather station face down on a flat and soft surface.
Slide and remove the battery cover at the back of your unit.
Insert 2 x new AA batteries into the battery compartment by observing the correct “+” and “-” polarity.
Slide and replace the battery cover.

Remarks:
Do not mix old and new batteries. Do not mix alkaline, standard or rechargeable batteries. Alkaline batteries are recommended for optimal usage of this clock.

If AC power is interrupted, the backlight can light 8 seconds, by pressed Snooze button, alarm can work, but projection does not function when only backup batteries are used to power your unit. The backup batteries will keep all settings of your unit.

TO INSTALL THE OUTDOOR TRANSMITTER

After your weather station is powered up, put it and the wireless outdoor transmitter next to each other. Then slide open the battery cover at the back of your wireless outdoor transmitter, insert 2 x AAA alkaline batteries to the battery compartment by observing the correct “+” or “-” polarity. Replace the battery cover. Your weather station will receive data signal from the outdoor transmitter in a few second. The OUT temperature and humidity will be displayed.

Insert the holder to the bottom of the outdoor transmitter for desktop or insert it to the back of the transmitter for wall mount purpose.

Remarks:
Keep in mind that your outdoor sensor has a 50-meter open air transmission with no obstructions. Actual transmission range will vary depending on what is in the path of the signal. Each obstruction (roof, walls, floors, ceilings, thick trees, etc.) will effectively decrease signal range.

MAJESTIC-WT-249-LCD-Weather-Station-with-Projection-
Overview

TO SET THE WEATHER STATION

You can set your weather station in the sequence of time, 12/24HR, calendar, snooze duration and weather forecast condition.

Press and hold SET, the hour digits flash. Press / OUT or /C/ F button to set the hours. Press and hold / OUT or /C/ F will accelerate your setting.
Then press SET again, the minute digits flash. Press / OUT or /C/ F button to set the minutes. Press and hold / OUT or /C/ F will accelerate your setting.
Press SET once again, the time digits change to “24Hr”. Press / OUT or /C/ F to select “12Hr” time format. When 12Hr time format is selected, PM indicator will be displayed.
Press SET once again, “2019” digits flash. Press / OUT or /C/ F button to set the year.
Press SET once again, month digits flash. Press / OUT or /C/ F button to set the month.
Press SET once again, date digits flash. Press / OUT or /C/ F button to set the date.
Press SET once again, “n05” flash. Pres s / OUT or /C/ F button to set the snooze duration from 5 minutes to 60
minutes.
Press SET once again, weather icons flash. Press / OUT or /C/ F button to set the current weather condition.
SUNNY|
---|---
SUNNY AND CLOUDY (PARTLY SUNNY)|
CLOUDY|
RAINY|
STORMY|
Then press SET once again to save the settings, or it will return to normal mode in around 10 seconds if no further press of any other buttons.

TO SET ALARM 1 AND 2

At normal time display mode, press and hold AL 1.2 / ON.OFF, icon and the alarm hour digit flash. Press / OUT or /C/ F to set the hours of your desired alarm time.
Press AL 1.2 / ON.OFF once again, the alarm minute digits flash. Press **/ OUT or /C/ F** button to set the minutes of your desired alarm time.
Press AL 1.2 / ON.OFF once again, “1-7” flash. Press / OUT or /C/ F button to select “1-7” or “1-5” or “6-7” or “1-1”
1-7 : daily alarm (alarm works through Monday to Sunday)
1-5 : weekdays alarm (alarm works through Monday to Friday only)
6-7 : weekends alarm (alarm works Saturday and Sunday only)
1-1 :single day alarm (alarm only works for one single time and then off)
Press SET once again to complete set-up. If no key is pressed the settings are automatically saved in approximate 10 seconds.

TO TURN ON OR OFF YOUR DAILY ALARM

At normal time display mode, press AL 1.2 / ON.OFF once to turn on Alarm 1 only, ****appears on the LCD.
Press AL 1.2 / ON.OFF once again to turn on Alarm 2 only, **** appears on the LCD.
Press AL 1.2 / ON.OFF once again to turn on both Alarm 1 & 2, both and appear on the LCD.
Press AL 1.2 / ON.OFF once again to turn off both Alarm 1 & 2, both and disappear on the LCD.

TO USE SNOOZE ALARM

When time reaches your set alarm time, your weather station will give a beep sound to wake you up. The corresponding or will flash.

1. Press SNOOZE once to stop the alarm temporarily, the corresponding or keeps flashing. The alarm will beep again according to your set snooze duration.
When the alarm is sounding, press AL 1.2 / ON.OFF once, the alarm will stop for the day, or become static. Alarm Duration: 2 minutes

TO USE THE HI-LO DIMMER

At normal time display mode, press SNOOZE to adjust the brightness (Hi/ Lo/ Off) of the LCD display. This can only be done when the AC/DC adaptor is being used.

Remarks: if only the backup batteries are used, press SNOOZE once to activate the backlight for 8 seconds. It is not possible to keep the display on during the use of the product with batteries.

TO DISPLAY TEMPERATURE IN DEGREE °C OR °F

Simply press **/ C/** F to display temperature in degree °C or degree °F.

TO USE THE PROJECTION (operated by adaptor only)

Press PROJECT once to turn on the projection. Press PROJECT again to reduce the projection light.
Press and hold PROJECT to activate auto scrolling function to view the current outdoor temperature (rounded to the nearest digit) and the current time for 5 seconds alternately. Press / C/ F to select degree Celsius or degree Fahrenheit temperature readout in projection view. Keep pressed PROJECT for 3 seconds again to turn off auto scrolling function.
Press PROJECT once again to turn off the projection.

When the projection is on, press and hold SNOOZE to flip the projection view upside down. At the back of your unit, use the rotary knob to rotate the projection view by 90 degree.

WEATHER FORECAST INDICATOR

There are five possible types of weather icons that will be displayed:

SUNNY|
---|---
SUNNY AND CLOUDY (PARTLY SUNNY)|
CLOUDY|
RAINY|
STORMY|

Remarks: Moving your weather station from one floor of a building to another floor will affect the accuracy of your weather station, which should operate at the same altitude all the time. If you move it to a new location, it will take 12 hours to get stable and accurate again.

IF YOU LOSE THE OUTDOOR TEMPERATURE AND HUMIDITY

When the outdoor temperature and humidity digits show ‘—“, the wireless transmission is either interrupted or lost. Press and hold the / OUT button to start searching for the signal from the outdoor transmitter with the ****flashing.
If you continue to lose the outdoor temperature and humidity display, which could happen in extreme cold weather, try placing the transmitter in a different location until you have smooth transmission of temperature / humidity data.

LOW BATTERY INDICATION OF YOUR OUTDOOR TRANSMITTER

The icon will appear to indicate the battery level of your outdoor transmitter is getting low. You may need to replace the batteries of your outdoor transmitter with new ones. Extreme cold weather (e.g. below 14 °F) will also cause low battery voltage.

CARE OF YOUR WEATHER STATION CLOCK

Do not expose the unit to extreme temperature, water or direct sunlight.
Avoid contact with any corrosive materials
Do not subject the unit to excessive force, dust or humidity.
Do not open the inner back case or tamper with any components of this unit.
Do not plug in any other AC/DC adaptor with incorrect specifications or voltage
Always place your outdoor transmitter in a dry and shaded area away from direct sunlight or rain.