Alpine Corporation WCT688 Pump Barrel Fountain Owner’s Manual

: August 13, 2024
: Alpine CORPORATION

Table of Contents

Alpine Corporation WCT688 Pump Barrel Fountain
WHAT’S INCLUDED
FEATURES
SPECIFICATIONS
ASSEMBLING & USING YOUR PRODUCT
TROUBLES HOOTING
LIMITED WARRANTY INFORMATION
FREQUENTLY ASKED QUESTIONS
VIDEO – PRODUCT OVERVIEW
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Alpine Corporation WCT688 Pump Barrel Fountain

WHAT’S INCLUDED

Fountain Top
Fountain Base
Water Pump Handle
Fountain Pump
Nut & Bolt
Bag of Rocks

FEATURES

UL Listed Outdoor Rated Pump
Cascading Water for the perfect accent
Made from durable Polystone

SPECIFICATIONS

Power Requirements ………Standard Household 120V
Water Capacity ………………..1-¾ US Gallon / 6 Liters
Tubing Diameter ………………………………………3/8” I.D.

ASSEMBLING & USING YOUR PRODUCT

Unpack all components carefully. Please check to ensure all parts have been removed from the packaging. *Some splashing may occur when the product is in use.

Place the Fountain Base on a smooth and level surface. Allow enough space to access the pump.
Now mount the Fountain Top to the Fountain Base. The Fountain Top hose will slide through the hole in the top of the Fountain base. Use the alignment notch on the rear of each piece for a proper fit.
Remove the pump from its packaging and adjust the flow control to the lowest setting to avoid splashing until the fountain is completely assembled.
Connect the vinyl tubing from inside the FountainBase. This is the same tubing that leads to the fountain Top. Then place the pump inside the fountain Base.
Add the Water Pump Handle to the Fountain top by inserting the handle shaft into the center of theFountain Top. Then line up the handle and insert the Bolt through the handle pivot point. Secure the bolt with the Nut on the other side.
Gently pour water into the fountain basin, being careful not to overflow and cause splashing. Make sure the water completely submerges the pump and the water runs clear during operation.
NOTE: We recommend that you use distilled water to prevent scale build- up. The first time you operate the pump it can take up to 5 minutes for the air to be completely expelled and water begin to flow properly
Plug the pump cord into your local power supply. Make sure that there is no water around the plug& always keep the power source in a dry place.
Now adjust the water pump to your flow preference. (see Quick Tip #1) Add the included rocks to the Pail of the Fountain.
Congratulations, your fountain is now complete. Don’t forget to add water regularly as water will evaporate over time.

Relax and enjoy your new fountain

REPLACEMENT PART ITEM#

Replacement Pump ……………………..P065

ALSO AVAILABLE FROM ALPINE

Fountain Care Formula ………………..PPL102
Foam and scale remover for indoor and outdoor fountains.
Americana® UV Acrylic Sealer ………RRR106
Provides protective clear coating for all painted surfaces.
Touch Up Paint Kit ….………………….RTD102
Includes primer, thinner, 7 paint colors, applicator, and sealer.

TROUBLES HOOTING

If you have any questions and/or problems, please contact the retail store where you purchased this fountain.

If your pump fails to run

Check the circuit breaker or try a different outlet to make sure the pump is receiving electrical power.
Check the pump discharge and tubing for any kinks and/or obstructions
Any buildup obstructing the water flow can be flushed with a garden hose
Check the rotor by removing the front cover & plate to access the impeller area. Turn the rotor and make sure that the rotor is not jammed or broken

If your pump “spews”

Check the water level to make sure the pump is completely submerged and there is enough water in the basin to operate your fountain. Not having enough water will cause your pump to spew

If your pump is making abnormally loud noises

Disconnect the pump from the electrical power supply and remove the front cover & plate
Carefully grip the impeller and gently pull the impeller/rotor assembly out of the pump housing
Rinse the impeller/rotor assembly and clean the cavity with clean water. If breakage or damage is found, contact your local retailer for parts.

CAUTION

Always unplug the pump from the electrical outlet before cleaning & handling
Use with clean water only, do not place the fountain and/or parts in any other liquid.
Periodically change the water & clean the pump to keep free from microorganisms
Disconnect and store the unit in a dry place if not in use for an extended period of time
Do not operate with water above 90°F or 30°C
Do not lift, carry, or pull the pump by the power cord
Do not exceed the maximum voltage & wattage on the transformer
NEVER LET THE PUMP RUN DRY

LIMITED WARRANTY INFORMATION

Thank you for choosing an Alpine product! We aim to please with our wide range of products including Fountains, Birdbaths, Statuary, Pond Supplies & More. All of our products are constructed from the highest quality materials. In the event that we have not achieved our usual standard of excellence, we will repair or replace, at our discretion, within the warranty period. A valid proof of purchase, with the purchase date clearly indicated, must be provided. Photos of defective merchandise will also be required to help distinguish the actual cause of the defect. Please read below for a detailed description of warranty coverage.

Water Damage Alpine products are not manufactured to withstand extreme temperatures. Improper storage that allows water to freeze within a product may cause damage, is considered negligence, and will not be covered under this warranty. The use of “hard water,” and/or caustic cleaners, can affect the painted or other finishes. Failure to keep the unit clean, and use of such additives/cleaners, will also void the warranty. Please note: for fountains, it is normal for some splashing to occur, and protecting the immediate surfaces is not the responsibility of Alpine Corporation.
Paint & Color (Retention and/or Loss) The use of water will cause natural erosion to the color. This area can be touched up using standard paint. The paint is designed to protect the entire finish against the breakdown of color. As with any product, all finishes with time will gradually fade and discolor. The warranty will only cover against severe or complete fading, within the first year from the date of purchase, with the above exclusion.
Procedure/Service Should a warranty/claim be needed, you should contact the retailer from whom you purchased the product. If that is not an option, you can contact Alpine Corporation at www.alpine4u.com. When contacting Alpine Corporation, you must be prepared to show proof of purchase and provide photographs and any other information needed to validate your claim. This may be necessary to distinguish between a partial or complete replacement of a defective product. The warranty does not cover any items with multiple parts; the warranty will ONLY cover the individual component of the unit/item that may be defective. Replacement parts can be made available to a consumer through the original selling party, or an approved parts retailer. If this is not an option, contact our customer service department. Item is covered under a one-year limited warranty from the date of purchase. When requesting replacement parts due to a warranty claim after 30 days of purchase, credit card information will be requested for shipping charges.

Not Covered Under Warranty

The limited warranty will NOT cover cases of damages due to:

Damages caused in Transit
Inadequate care and/or neglect
Environmental and/or natural elements
Immersion in water, unless specified
Improper Installation/Storage and/or Maintenance

This warranty is void if the product has been damaged by accident, misuse, negligence, improper installation, and/or modifications have occurred. This includes any and/or all defects arising out of freezing water damage, hard water damage, failure to keep the unit clean and free of harmful additives such as bleach, chlorine, etc…. which affect the paint and/or parts. This warranty also does not cover any additional charges or installation, removal, disposal, and/or shipping costs or consequential damage associated with any warranty claim.

Purchased your product online?

We would really appreciate it if you could share your experience with others by reviewing our product on the website from which you purchased it.

Have Questions or Issues? Need help with assembly? Contact us and we will resolve them within 12 hours.

Support Hours: M-F 7:30–5:00 (U.S. Pacific Time)
Call: 877-460-4511
Email: info@alpine4u.com

FREQUENTLY ASKED QUESTIONS

What are the dimensions of the Alpine Corporation WCT688 Pump Barrel Fountain?

The dimensions are 12 inches in length, 9 inches in width, and 24 inches in height.

How much does the Alpine Corporation WCT688 Pump Barrel Fountain weigh?

It weighs 9.9 pounds.

What is the power source for the Alpine Corporation WCT688 Pump Barrel Fountain?

The fountain is powered by a corded electric connection.

Who is the manufacturer of the Alpine Corporation WCT688 Pump Barrel Fountain?

The manufacturer is Alpine Corporation.

What is the price of the Alpine Corporation WCT688 Pump Barrel Fountain?

The price is $71.50.

How does the Alpine Corporation WCT688 Pump Barrel Fountain's durability benefit users?

Its durable resin construction ensures longevity and resistance to weathering, making it a lasting addition to any outdoor or indoor space.

What kind of maintenance is required for the Alpine Corporation WCT688 Pump Barrel Fountain?

Maintenance includes regular cleaning to prevent algae buildup, checking the water level, and ensuring the pump is working properly.

How does the design of the Alpine Corporation WCT688 Pump Barrel Fountain enhance its aesthetic appeal?

The rustic pump barrel design adds a charming, antique look to the fountain, enhancing the visual interest and creating a calming water feature.

Why is the water flow in my Alpine Corporation WCT688 Pump Barrel Fountain weak or inconsistent?

Ensure that the pump is fully submerged and that there are no blockages in the tubing. Clean the pump and tubing to remove any debris that may be restricting water flow.

What should I do if my Alpine Corporation WCT688 Pump Barrel Fountain is making loud or unusual noises?

The noise could be due to low water levels causing the pump to run dry. Make sure the fountain is filled with enough water and check the pump for any debris or obstructions.

How can I fix the issue if my Alpine Corporation WCT688 Pump Barrel Fountain is not turning on?

Check that the fountain is properly plugged into a functioning power outlet. Inspect the power cord and plug for any damage. If the problem persists, try resetting the outlet or using a different one.

Why is my Alpine Corporation WCT688 Pump Barrel Fountain leaking water?

Ensure that the fountain is placed on a level surface and that all connections are secure. Check for any cracks or damage in the barrel or basin that might be causing leaks.

What should I do if the pump in my Alpine Corporation WCT688 Pump Barrel Fountain stops working?

Unplug the fountain and clean the pump to remove any debris. Check if the impeller inside the pump is moving freely. If cleaning doesn’t solve the issue, you may need to replace the pump.

How do I prevent algae buildup in my Alpine Corporation WCT688 Pump Barrel Fountain?

Regularly clean the fountain and replace the water to prevent algae growth. Consider using a fountain-safe algaecide to keep the water clear.

Why is my Alpine Corporation WCT688 Pump Barrel Fountain splashing water outside the barrel?

Make sure the water level is not too high and check that the pump flow rate is not set too high. Also, ensure the fountain is on a level surface to minimize splashing.