VOLLRATH 3877860 Cafeteria Breath Guard Instruction Manual
- August 11, 2024
- VOLLRATH
Table of Contents
VOLLRATH 3877860 Cafeteria Breath Guard
Specifications
- Product Name: Cafeteria Breath Guard
- Model: One Piece and Three Piece options available
- Manufacturer: Vollrath Company, L.L.C.
- Item No.: 2350030-01
Product Usage Instructions
One Piece Breath Guard Installation:
Install the breath guard uprights (A) to the studs (B) securing with cap
nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C). Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C). Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C). Repeat on the other side.
- Install the side breath guards (E) securing them with screws (F) and cap nuts (C). Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C). Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
These instructions cover the installation of the one-piece Cafeteria Breath Guard and the three-piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
MORE INFORMATION
The Vollrath Company, L.L.C.
- ADDRESS: 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.628.0830
- Service Tel: 800.628.0832
- FAX: 800.752.5620
Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.
www.vollrathco.com
FAQ
- Q: What should I do if I accidentally over-tighten the cap nuts?
- A: If you accidentally over-tighten the cap nuts and cause cracking, please contact Vollrath’s Service Tel: 800.628.0832 for assistance.