VOLLRATH 3873260A Cafeteria Breath Guard Installation Guide
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 3873260A Cafeteria Breath Guard
Product Information
- Brand: Vollrath
- Model: Cafeteria Breath Guard
- Types: One Piece and Three Piece
- Item No.: 2350030-01 Rev 04/12
Product Usage Instructions
One Piece Breath Guard Installation
Install the breath guard uprights (A) to the studs (B) securing with cap nuts
(C) as shown in Figure 1. Repeat for all four uprights.
Three-Piece Breath Guard Installation
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
FAQ
-
Q: What should I do if the plastic cracks during installation?
A: If you notice any cracks in the plastic components, stop installation immediately and contact Vollrath’s Service Tel for assistance. -
Q: Can I tighten the cap nuts with a power tool?
A: It is recommended to tighten the cap nuts by hand to avoid overtightening and potential damage to the plastic parts.
Installation Instructions
One Piece Cafeteria Breath Guard Three Piece Cafeteria Breath Guard
These instructions cover the installation of the one-piece Cafeteria Breath
Guard and the three-piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Three-Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
Contact Information
The Vollrath Company, L.L.C.
- Add: 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.628.0830
- Service Tel: 800.628.0832
- FAX: 800.752.5620
Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>