VOLLRATH 36672auto Manifold Drain Kit Instruction Manual

: June 1, 2024
: VOLLRATH

Table of Contents

VOLLRATH 36672auto Manifold Drain Kit
Safety Precautions
Operational Statement
Unpacking the equipment and initial SetUp
Warranty Statement for the Vollrath co. l.l.c.
Read User Manual Online (PDF format)
Download This Manual (PDF format)
2 Flat Blade Screwdriver
2 Phillips Screwdriver

VOLLRATH 36672auto Manifold Drain Kit

Specifications

Item 36672auto: Auto Manifold Drain Kit, 2 Well
Item 36673auto: Auto Manifold Drain Kit, 3 Well
Item 36674auto: Auto Manifold Drain Kit, 4 Well
Item 36674man: Manual Manifold Drain Kit, 2-4 Well
Voltage: 120V (for all auto kits), N/A (for manual kit)

For Use With:

3667201D or 3667202D for Item 36672auto
3667301D or 3667302D for Item 36673auto
3667402D for Item 36674auto

Safety Precautions

To ensure safe operation, follow these safety precautions:

Read and understand all installation and operation instructions
before using the equipment.
Have the equipment installed by a licensed electrician or
certified service personnel.
Ensure the unit is unplugged before installation.
Use only grounded electrical outlets matching the rated voltage.
Avoid spraying controls or the exterior of the equipment with liquids or cleaning agents.
Keep the equipment and power cord away from open flames, electric burners, or excessive heat.

Item Description Voltage For Use With

Thank you for purchasing this Vollrath equipment. Before operating the equipment, read and familiarize yourself with the following operating and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Save the original box and packaging. Use this packaging to ship the equipment if repairs are needed.

Safety Precautions

To ensure safe operation, read the following statements and understand their meaning. Please read carefully.

WARNING
Warning is used to indicate the presence of a hazard that can cause severe personal injury, death, or substantial property damage if the warning is ignored.

CAUTION
Caution is used to indicate the presence of a hazard that will or can cause minor personal injury or property damage if the caution is ignored.

NOTE
Note is used to notify people of installation, operation, or maintenance information that is important but not hazard-related.

For Your Safety!
These precautions should be followed at all times. Failure to follow these precautions could result in injury to yourself and others.

To reduce risk of injury or damage to the equipment:

Read and understand all installation and operation instructions before installing or operating equipment.
This equipment must be installed by a licensed electrician or certified service personnel.
Prior to installation the unit must be unplugged from its power source.
Use only grounded electrical outlets matching the nameplate rated voltage.
Do not spray controls or outside of equipment with liquids or cleaning agents.
Keep equipment and power cord away from open flames, electric burners or excessive heat.

Function and Purpose
Drain kits 36672auto, 36673auto, 36674auto and 36674man are designed to be installed on Vollrath Hot/Cold Well models only. Check vollrathco.com for product list.
This product is intended to drain the water from a well.
This equipment is not intended for household, industrial or laboratory use.

Operational Statement

The Auto Drain units operate by emptying the reservoir after the mode switch on the unit it is moved to the refrigeration mode. When the well control switch is in the refrigerate mode the valve stays in the “open” position. When the well control switch is in the center or heat position the valve remains in the “closed” position.
The Manual Drain units require an operator to manually install a drain plug in order for the well to hold water or to remove the drain plug to allow the water to drain.

Unpacking the equipment and initial SetUp

When no longer needed, dispose of all packaging and materials in an environmentally responsible manner. Have the unit installed only by qualified service personnel. This unit must be installed in accordance with any local and national plumbing codes. See back of this document for kit contents.

Tools and Supplies Required:

2 Flat Blade Screwdriver
2 Phillips Screwdriver
Wire Stripper
Pipe Wrench or Pliers
Silicone, High Temperature, NSF Listed
Utility Knife

Installation of Auto Drain Model Kits:

Turn power switch to the “OFF” position and unplug from power source.
Remove all water from the wells.
Remove the stub pipe (B) by unscrewing it from the well bottom (A). See Figure 1.
Place a small bead of high temperature NSF listed silicone on the threads on fitting (B) of the valve assembly (C). See Figure 2.
Thread the fitting (B) into the well bottom (A) and tighten.
Repeat steps 2-5 as necessary to install more valves.
Remove the hardware securing the cover (A) on the wire channel box (D). See Figure 3.
Loosen the screws (B) on the strain relief.
Route the auto drain cords (C) through the strain reliefs. $VOLLRATH-36672auto-Manifold-Drain-Kit-eatured $5$$
Make the connections as shown in Figure 4 using the lever connectors and blue and white wire(s) provided. Also refer to unit wiring diagram.
To use the lever connectors (See Figure 5):
$VOLLRATH-36672auto-Manifold-Drain-Kit-eatured $6$$
Strip 3/8” (10 mm) of insulation (C) from the wire. There is a gauge that shows the correct measurement to be stripped on the lever connector. Twist the exposed wire slightly so that is stays together inside the connector.
Lift lever to the up position (A).
Insert the stripped portion of wire into the lever connector and put lever into the closed position (B). no bare wire can be exposed from the connector.
After all the connections have been made secure the cover (A) onto the wire channel box (D) using the hardware that was removed earlier. Figure 3.
Tighten the screws (B) by hand to prevent cutting the wire insulation. See Figure 3.
Cut and install the drain tubing (C), “T” fittings (D) and clamps (B) as needed and route to drain. See Figure 6.
Tighten all clamps.
Install the unit, read and follow the Operator’s Manual instructions for safe and correct use.
Pour 1/4 cup of clean fresh water into each well drain. Switch the mode control to refrigeration. See Operator’s manual. Turn the power switch to the “ON” mode. Water should drain. Repeat for all wells.

Installation of Manual Drain Model Kits:

Turn power switch to the “OFF” position and unplug from power source.
Remove all water from the wells.
Cut and install the drain tubing (C), “T” fittings (D) and clamps (B) as needed and route to drain. See Figure 7.
Tighten all clamps.
Install the manual “drain plug(s)” provided in the well bottoms to hold water in the wells. See operation of manual drain plug on following page.
Wait until the water in the well has completely cooled before removing the manual “drain plug(s)”.

Operation of the Manual Drain Plug:

To install the manual drain plug:

Install the drain plug assembly into the drain hole of the well (C). See Figure 7.
If necessary hold shaft (A) and tighten the wing nut (B). This will expand the rubber collars (D). Turn the wing nut until it is snug.

To remove the manual drain plug:

If necessary hold shaft (A) and loosen the wing nut (B). This will contract the rubber collars (D). Turn wing nut until it is loose.
Remove the drain plug from the drain hole in the well (C).

$VOLLRATH-36672auto-Manifold-Drain-Kit-eatured $11$$

Warranty Statement for the Vollrath co. l.l.c.

The Vollrath Company LLC warrants the products it manufactures and distributes against defects in materials and workmanship for a period of one year, except as specifically provided below. The warranty runs 12 months from the date of original installation. (End user receipt)

Refrigeration compressors – The warranty period is 5 years.
Replacement parts – The warranty period is 90 days.
Fry pans and coated cookware – The warranty period is 90 days
EverTite™ Riveting System – The warranty covers loose rivetsonly, forever.
Cayenne® Heat Strips – The warranty period is 1 year plus an additional 1 year period on heating element parts only.
Ultra and Professional Induction Ranges – The warranty period is 2 years.
Mirage and Commercial Induction ranges – The warranty period is 1 year.
ServeWell® Induction Workstations – The warranty period is one year on the workstation table and 2 years on induction hobs.
Slicers – The warranty period is 10 years on gears and 5 years on belts.
Mixers – The warranty period is 2 years.
Extended warranties are available at the time of sale.
Vollrath – Redco products – The warranty period is 2 years.
Optio / Arkadia product lines – The warranty period is 90 days.
All non-stick products (i.e. fry pans and surfaces) are 90 days for the non stick surfaces.

All products in the Jacob’s Pride® collection, including the following, have a lifetime warranty:

NSF Certified One-Piece Dishers
NSF Certified Spoodle® Utensils
NSF Certified Heavy-Duty Spoons with

Ergonomic Handle

NSF Certified Heavy-Duty Basting Spoons
Heavy duty Turners with Ergonomic handle
One-Piece Tongs*
Heavy-Duty One-Piece Ladles*
Nylon Handle Whips
One-Piece Skimmers
Tribute®, Intrigue®, and Classic Select®

Cookware
Jacob’s Pride® warranty does not cover Kool-Touch®, non stick coatings and silicone handles.

Items sold having no warranty:

Meat Grinder Knives
Light Bulbs in Convection Ovens andHot Food Merchandiser
Oven Door Seals
Oven Door Glass
Hot Food Merchandisers / Display Case

Glass

Calibration and set up of gas equipment
Slicer / Dicer blades (table top food prep) – Redco and Vollrath

This WARRAnTY is in liEU OF AnY OThER WARRAnTiEs, EXPREss OR iMPliED, inClUDing AnY iMPliED WARRAnTY OF MERChAnTABiliTY OR FiTnEss FOR A PARTiCUlAR PURPOsE
As The Vollrath Company LLC’s only responsibility and the purchaser’s only remedy, for any breach of warranty, The Vollrath Company LLC will repair or, at its option, replace the defective product or part without charge, except as otherwise provided below:

For refrigeration compressors and the second year of the warranty on Cayenne® Heat Strips and mixers, The Vollrath Company LLC will provide the repaired or replacement part only; and the buyer will be responsible for all labor charges incurred in performing the repair or replacement.
To obtain warranty service, the buyer will be responsible to return to The Vollrath Company LLC any product (other than gas equipment that is permanently installed) weighing less than 110 lbs. or located outside of a 50-mile radius of a certified technician designated by The Vollrath Company LLC to perform warranty repairs. If a Vollrath Technician cannot be contacted check the website for service contact points. (Please refer to the Product Catalogue for weights and sizes of product)
No remedy will be available for products that have been damaged by accident, carelessness, improper installation, lack of proper setup or supervision when required, neglect, improper use, installation or operation contrary to installation and operating instructions or other causes not arising out of defects in materials or workmanship. At the buyer’s request, The Vollrath Company LLC will repair and or replace such products at a reasonable cost.
No remedy will be available for slicers where blade has not been sharpened (Refer to owner’s manual for sharpening instructions)
No remedy will be available for mixers damaged by changing gears while unit is running or overloading, in either case as determined by a Vollrath Certified Technician
Warranty work must be authorized in advance by The Vollrath Company LLC. See the operating and safety instructions for each product for detailed warranty claim procedures. • No remedy will be available for product returned and found to be acceptable to the product specification.
No remedy will be available under any warranty not registered as required below.

Limitation OF Liability
ThE VOllRATh COMPAnY llC shAll hAVE nO liABiliTY FOR inCiDEnTAl OR COnsEQUEnTiAl DAMAgEs OF AnY KinD, WhEThER BAsED UPOn nEgligEnCE OR OThER TORT, BREACh OF WARRAnTY, OR AnY OThER ThEORY.

Warranty Procedure
On all warranty calls, the following process and information is required:

All warranty claims will start with a call to Vollrath Technical Service support line.(800-354-1970).
A technical support professional will work to diagnose the issues, and provide the details for the service solution.
Name and phone number of person calling
Business name, street address, city, state and zip
Model and serial number
Date of purchase and proof of purchase (Receipt)
Name of dealer where unit was purchased

NOTE: Vollrath will not accept products sent without the proper procedure being followed.

important:
TO MAKE A CLAIM FOR ANY REMEDY UNDER THIS WARRANTY, YOU MUST REGISTER YOUR WARRANTY.

register today
ONLINE: Register your warranty on-line now at www.Vollrathco.com
NO WEB ACCESS: If you do not have access to the web, kindly register by completing the warranty registration form and faxing it to The Vollrath Co. LLC office in the country of purchase.

$VOLLRATH-36672auto-Manifold-Drain-Kit-eatured $1$$ www.vollrathco.com