VOLLRATH 38737W Cafeteria Breath Guard Installation Guide
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 38737W Cafeteria Breath Guard
Specifications
- Product Name: Cafeteria Breath Guard
- Model: One Piece / Three Piece
- Manufacturer: The Vollrath Company, L.L.C.
- Item No.: 2350030-01 Rev 04/12
Product Usage Instructions
One Piece Breath Guard Installation
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three-Piece Breath Guard Installation
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights(A) securing with cap nuts (C). Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F)and cap nuts (C) as shown. Repeat for all four mountinglocations.
- Install the side breath protector (G) to the support tube (D)securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the sidebreath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mountinglocations.
Installation Instructions
One Piece Cafeteria Breath Guard Three Piece Cafeteria Breath Guard
These instructions cover the installation of the one-piece Cafeteria Breath
Guard and the three-piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
Three-Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
The Vollrath Company, L.L.C.
1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.628.0830
- Service Tel: 800.628.0832
- FAX: 800.752.5620
- Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
© 2010 The Vollrath Company, L.L.C.
FAQ
- Q: What should I do if I encounter cracks while tightening the cap nuts?
- A: If you encounter cracks while tightening the cap nuts, stop immediately to prevent further damage. Contact customer service for assistance.
- Q: Can I disassemble and reassemble the breath guard easily?
- A: Yes, you can disassemble and reassemble the breath guard following the installation instructions in reverse order. Ensure to handle all components with care to avoid damage.