SEURA Alto, Fresco, Legato, Opus, Concerto Mirrors User Manual
- August 9, 2024
- SEURA
Table of Contents
SEURA Alto, Fresco, Legato, Opus, Concerto Mirrors
Product Information
Specifications
- Models: Alto, Fresco, Legato, Opus, Concerto
- Designs: Lighted Mirror
- Tools Needed: Wall Bracket, 2-3 Wire Nuts, 2-3 Phillips-Head Screws (M4), 2-3 Wall Anchors, Phillips-Head Screwdriver, 3/8 Drill bit, Drill
Product Usage Instructions
Unboxing Instructions
- Lay the box on the ground face up.
- Carefully tip the box on its side and cut the tape holding the top part of the box in place.
- Lower the box back down and remove the lid.
- Carefully remove the large cardboard piece from on top of the mirror.
- Remove the mirror. Tip: Save the box and packaging materials until installation is complete.
- Gently cut the tape and remove the Styrofoam pieces.
- Flip the mirror upside down and gently pull the remaining foam pieces up and off the mirror.
- Remove the plastic polybag.
- Once the mirror is installed on the wall, gently remove the protective plastic film from the glass.
Installation Instructions
-
Prepare Wall: Decide on the desired mirror location on the wall.
Rectangle mirrors can be mounted vertically or horizontally. Mark at least 2 mounting hole locations on the wall with a pencil. Turn off the power source before making any changes to electrical connections. -
Install Wall Anchors: Drill pilot holes at marked locations.
- Install wall anchors and screw into the wall, ensuring bracket orientation.
-
Mount the Wall Bracket: Ensure the mirror bracket engages with the installed wall bracket securely.
Operating Instructions
- Tap the the button to power the lights on and off.
- Touch and hold to adjust from 100% full brightness to 10% ambient low lighting.
Maintenance
How to Clean: [Add cleaning instructions here]
Frequently Asked Questions
Q: What should I do if my mirror housing contains reflective tape or white tape?
A: Do not remove it as it may damage the product. The adhesive tape is used for some models and is not part of the packaging.
Q: How do I activate my warranty for extra benefits?
A: You can activate your warranty within 30 days of purchase by visiting seura.com/activate.
Thank you for selecting a Séura Lighted Mirror
Please read this guide before beginning installation.
- Carefully remove and inspect the unit for possible damage that may have occurred during shipping. If there is damage, please call Séura at 1-800-957-3872.
- If your shipment is damaged and is not noted on the delivery receipt, Séura cannot guarantee compensation.
- All freight damage claims must be reported to Séura Customer Service within 48 hours of delivery to be covered by our warranty.
How to properly remove the unit from the box
- Lay the box on the ground face up.
- Carefully tip the box on its side and cut the tape holding the top part of the box in place
- Lower the box back down and remove the lid.
- Carefully remove a large cardboard piece from on top of the mirror.
- Remove the mirror. Tip : Save the box and packaging materials until installation is complete.
- Gently cut the tape and remove the Styrofoam pieces.
- Flip the mirror upside down and gently pull the remaining foam pieces up and off the mirror.
- Remove the plastic polybag.
- Once the mirror is installed on the wall, gently remove the protective plastic film from the glass.
- If the mirror or mirror housing contains reflective tape or white tape, do not remove it.
- Adhesive tape is used on some models and is not part of the packaging.
- Removing the adhesive will damage the product.
How to properly store the unit until installation
- After inspection, repack the unit so it stays safe and protected until installation.
- NOTE: It is the installer’s responsibility that all electrical and framing construction is code-compliant to the municipality in which the product is being installed.
- Modifications made to Séura recommendations are at the sole discretion of the installer and release Séura of all liability.
- Séura Lighted Mirrors use LEDs that are rated to retain 70% overall brightness at the end of life, including cases where an individual LED fails.
- WARNING: READ ALL INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL OR SERVICE THIS PRODUCT.
- When installing and during the use of this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following.
- Make sure the installation area is free of clutter.
- Do not place the product on an unstable cart, stand, tripod, or table.
- To avoid damage to the mirror, only transport it in a vertical position. Transporting the product horizontally may permanently warp the mirror.
- Inspect the desired location for installation and be aware of all electrical wiring pathways, water pipes, gas lines, or other potentially hazardous conditions that may exist to protect from accidental damage.
- Ensure all required electrical specifications are adhered to have been installed by the appropriate individuals and are code-approved.
- Ensure all framing requirements, if needed, have been completed to the building code and pose no structural issues.
- It is highly recommended that at least two (2) people assist in the installation of the mirror.
- Only qualified individuals should attempt to service the product.
- Close adult supervision is necessary when any product is used by or near children.
- Protect against electric shocks and burns by wearing safety gloves.
- Do not operate any product with a damaged cord or plug or operate it after the appliance malfunctions or has been damaged in any manner.
- Do not let the power cord or wiring come in contact with hot surfaces such as radiators, heat registers, stoves, or other products that produce heat.
- To protect against electric shock, do not immerse the power cord, power plug, or product in water or other liquid.
- This product is only intended for use indoors.
- This product is not waterproof. Do not immerse this product in water or expose it to dripping or splashing water as this could cause an electrical hazard.
- In damp locations, it is REQUIRED that the plug-in version of this product is plugged into an electrical outlet protected by a Ground Fault Circuit Interrupter (GFCI) to protect against electric shock, fire, and/or injury.
- Failure to do so will void any warranty for this product.
- The product must have proper, correct, and sufficient AC supply voltage.
- Retain this manual in a safe place for future reference.
- WARNING: Cancer and Reproductive Harm: www.p65warnings.ca.gov.
Components
INSTALLATION INSTRUCTION
Step 1 Prepare Wall
- Prepare the wall and decide on the desired mirror location on the wall. Rectangle mirrors can be mounted in vertical or horizontal orientation.
- After determining the wall bracket location, mark at least 2 mounting hole locations on the wall with a pencil.
- IMPORTANT: Turn off the power source before making any changes to electrical connections.
Step 2 Install Wall Anchors
- Drill 3/8-inch pilot holes at the marked locations.
- Insert the wall anchors into the pilot holes.
- Note: Anchors are only required when mounting to drywall and not required when mounted directly to wall studs.
Step 3 Mount the Wall Bracket
- Align Holes on the bracket to installed wall anchors and screw into the wall, ensuring the bracket is oriented as shown.
Step 4 Install Mirror
- Connect the plug to the power source
- Lift the mirror slightly above the installed wall bracket and slowly lower it, ensuring the mirror bracket engages with the installed wall bracket. Ensure the brackets are securely engaged before letting go of the mirror.
Operating Instructions
Operating the Touch Control Dimming button:
- Tap button to power lights on and off
- Touch and hold to adjust from 100% full brightness to 10% ambient low lighting
- Lift your finger off the button to stop at the preferred brightness
- Tap a button to turn the lights off. Your selected brightness will be saved and resumed the next time you turn on the mirror lights
- NOTE: Touch Button is constantly illuminated when the mirror has power
- NOTE: Touch Button is constantly illuminated when the mirror has power
Operating the Touch Control Defogger button:
- Tap the button to turn the defogger on and off
- NOTE: The touch Button is only illuminated when the defogger is on. For best results, it is recommended to turn defogger on 5 minutes before showering
Maintenance
- Our mirror technology has been developed to completely protect the mirror surface and allow easy maintenance. Please follow the guidelines listed for proper mirror care and cleaning:
- The glass surface can be cleaned with any conventional non-ammoniated glass cleaner. Care should be taken to use only a soft lint-free cloth. Apply all cleaners directly to the cloth and not the mirror surface.
- Never saturate the mirror surface as a residual cleaner may seep behind the mirror.
- Stubborn spots can be removed with solvents such as mineral spirits, denatured alcohol, and acetone. Immediately remove solvent and dirt residues per the prescribed methods above with a compatible glass cleaner or water.
WARRANTY REGISTRATION
REGISTER FOR EXTRA BENEFITS
- Activate within 30 days of purchase: seura.com/activate
- 1230 Ontario Road Green Bay, Wisconsin 54311 1-800-957-3872 contacts@seura.com www.seura.com
- Publish date: July 9, 2024 Information is subject to change without notice. © 2024 Séura
Documents / Resources
|
SEURA Alto, Fresco, Legato, Opus, Concerto
Mirrors
[pdf] User Manual
Alto Fresco Legato Opus Concerto Mirrors, Alto, Fresco, Legato, Opus,
Concerto, Mirror, Mirrors, Alto Mirrors, Fresco Mirrors, Legato Mirrors, Opus
Mirrors, Concerto Mirrors
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>