MILESEEY TP2 PLUS Thermal Imager Instruction Manual
- August 8, 2024
- MILESEEY
Table of Contents
MILESEEY TP2 PLUS Thermal Imager
Specifications
- FCC ID: 2AEOG-TP2PLUS
- Frequency Band: 5.15-5.25GHz
- Usage: Indoor only
FAQs
- Q: Can I use the product outdoors?
- A: No, operations in the 5.15-5.25GHz band are restricted to indoor usage only as per FCC regulations.
Warranty Statement
Warranty Statement
- For the complete products manufactured by Mileseey, from the date of initial purchase, there is a two-year warranty under the condition of normal storage, reasonable use, and maintenance.
- The warranty period for accessories is three months.
- This warranty is non-transferable and does not apply to any product damaged due to misuse, negligence, accidents, or abnormal operating conditions.
- If any defects occur in the product covered by this warranty, it must not be used further or repaired privately to prevent further damage. The purchaser must immediately report the product defect to
- Mileseey, otherwise, this warranty will not apply.
- If upon inspection by Mileseey, the product or accessory is found to be faulty, the user may contact Mileseey’s after-sales service department within the warranty period to negotiate repair or replacement of the product.
Quality Assurance
- The quality management system has been certified according to the 1SO9001 standard.
- We reserve the right to modify or improve any product without prior notice.
Safety Instructions
warning
- Before using cleaning solutions, ensure you have read all applicable Material Safety Data Sheets (SDS) and warning labels on the containers.
- Do not place the product in high-temperature environments exceeding 60°C or in low-temperature environments below -20°C. The device supports operation while charging.
- 1t is recommended to charge the device at room temperature conditions and when it is turned off. Do not charge in high-temperature environments above 40°C or low-temperature environments below 0°C.
- Do not operate the device in high-temperature environments exceeding 50°C or in low-temperature environments below -l0°C.
- The relative humidity for the device’s use is 10% to 95%, non-condensing.
- Do not arbitrarily disassemble or modify the infrared thermal imager.
FCC
Applicability: Class B digital devices.
- This device complies with part 15 of the FCC Rules. Of operation is subject to the following two conditions:
- This device may not cause harmful interference,
- this device must accept any interference received, including interference that may cause undesired operation.
- Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Frequency range of WLAN radio module: 5.l5-5.85GHz. Maximum power of WLAN radio module: 13dBm.(Only for EU) Mileseey Technology Co., Ltd. declares that the radio equipment type TP2 PLUS complies with Directive 2014/53/EU, 2011/65/EU. To comply with RF exposure requirements, a minimum separation distance of 0mm must be maintained between the user’s body and the handset, including the antenna.
Caution
-
Do not use the product under conditions that exceed the specified environmental requirements. Refer to the product specification sheet for specific environmental requirements.
-
Do not apply cleaning solutions or similar liquids directly onto the thermal imager, cables, or other components.
ese extremely cautious when cleaning the infrared lens. The lens has a delicate coating that can be damaged by rough materials like paper towels or excessive force. -
Avoid pointing the infrared thermal imager towards strong light sources or devices emitting laser radiation, regardless of whether the lens cap is on. This can affect the accuracy of the thermal imager and potentially damage its detector.
User Notice
- Calibration
- To ensure the accuracy of temperature measurements, we recommend calibrating the thermal imager annually.
- This calibration can be performed either by Mileseey or a third-party organization.
- Accuracy
- To achieve highly accurate results, we recommend that you wait for 5 minutes after turning on the thermal imager before beginning temperature measurements.
- (Includes switching temperature ranges)
- Documentation Updates
- Our manuals are updated several times a year, and we also regularly issue notices about key product changes.
- To access the latest manuals and notifications, please visit the Mileseey official website.
- Applicability
- This manual applies to all products within a series, which means that some functions described in this manual may not apply to a specific model within the series.
- Disposal of Electronic Waste
- 20l2/l9EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
- 2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or a designated collection point. For more
For information see: www.recyclethis.info.
COMPONENT GUIDE
- FrontView
- Back View
| Name | Function |
|---|---|
| Back Clamp | Flexible, used for clamping the phone |
SIDE VIEW
| Name | Function |
|---|---|
| USB interface | Charge using a used cable connected to a power adapter. |
Quick Operating Guide
Please follow the steps below:
l. Charging:
• U se a 5V 2A power adapter and USB cable to charge the device.
• Please charge the device at room temperature conditions.
2. Power On Press and ho ld the power
button to turn on the device.
3. Locate the Target Aim the thermal imager at the object
of your interest.
4. Capturing I mages Use the Mobile App on your
phone to cap t ure images by pressing the ima
ger button and record videos by p ress ing the
video button.
5 . APP Ana l ys i s Open the
accompanying App for the thermal ima ger; navigate to the
gallery; se lect the picture you need for
secondary analysis, and proceed w ith the ana
l ysis.
APP Description
App Overview
- ‘Thermal TP Series,” as the secondary analysis APP accompanying the thermal imager produced by Mileseey, is compatible with the TP series of wireless thermal imagers for observation use.
- It allows for viewing images in five different modes through the mobile app, including infrared, visible light, and dual-light fusion.
- The app features capabilities for pseudocolor switching, photography, video recording, and custom temperature analysis with points, lines, and frames.
App connectivity
- Press and hold the power button to turn on the device and ensure that the Bluetooth function of your smartphone is enabled.
- Open the “Thermal TP Series” app.
- Click on the device you want to connect to.
- A pop-up window will prompt the user: ”Thermal TP Series wants to join the wireless network TP2. Cancel or Join?” Click on “Join” to successfully connect ( this step is only necessary for iPhone models).
Introduction of the Main User Interface
Setting Interface
- Measurement Range:
- Options for low and high-temperature ranges are available; supports automatic switching of temperature ranges.
- Auto Power-Off:
- Supports custom settings for no auto shut-down, or automatic shut-down after lO or 20 minutes.
- Factory Reset:
- Ap to perform a factory reset. After resetting to ctory settings, all device information will be erased.
- Battery Capacity:
- Displays remaining battery life.
- Device Info:
- Allows viewing of the device model, PN(Port Number), SN (Serial Number), and firmware version number.
Cleaning
Clean the exterior casing, cables, and other components of the thermal imager.
Clean the exterior casing, cables, and other components of the thermal imager
Cleaning Solution| You can use one of the following liquids: warm water Mild
cleaning solution
Cleaning Tool| Soft cloth
Cleaning Steps| Please follow the following steps: Dip a soft cloth in the
cleaning solution. Wring out the soft cloth to remove excess cleaning
solution. Use a soft cloth to clean the components.
Warning: Avoid applying the solution or similar liquids directly onto the thermal imager, cables, or other components, to prevent damage to the device.
Clean the infrared imager lens
Clean the infrared imager lens
Cleaning Solution| You can use one of the following liquids: A commercial lens
cleaning solution with an isopropyl alcohol concentration of over 30%. 96%
concentration ethanol (C2H50H).
Cleaning Tool| Degreasing Cotton/Cotton Swab
Cleaning Steps| Please follow the following steps: Dip a piece of degreasing
cotton in a small amount of cleaning solution. Squeeze the degreasing cotton
to remove excess cleaning solution. Gently wipe the lens with the degreasing
cotton. The cotton should be used only once and not reused.
Warning: When cleaning the infrared lens, avoid applying excessive force. This could damage the lens”s anti-reflective coating.
Technical Parameter
| Model | TP2Plus |
|---|---|
| Thermal Sensor | uncooled Vanadium Oxide |
| Thermal Resolution | 256xl92 |
| Pixel Pitch | 12µm |
| wavelength Ronge | 7.5-14 µm |
| Frame Rate | 25Hz |
| Focal Length | 3.2mm |
| Lens Aperture | Fl.l |
| Field of View | |
| Type of Focus | Fixed |
| Focal Distance | 0.3m- |
| IFOV | 3.75mrad |
| NETO | 40mK |
| Visible Light camera (TP2 Plus only) | 200w |
| Color Palettes | White Hot/Black Hot/ Rainbow/Rainbow HC/ Lron/Lava/RdGy |
| Imaging Mode (TP2 Plus only) | Infrared, Visible Light, Picture in Picture, |
Fusion
Remote Access and Control| Capable Of Connecting To Smart Devices Via WiFi
From A Distance Of Up To 26ft (8m)
Device Compatibility
| Supports Smartphones with iOS 12.0 Or Higher And Android 9.0 Or Higher.
Clamp Width| Minimum 131/Maximum 165mm
Data Capturing| Video, Still Image
Picture Format| .jpg
Video Format| MP4
OTA| Supports OTA (Over-The-Air) upgrades.
WiFi| IEEE802.11 a/b/g/n/ac
Temperature Range| TP2 PLUS: -20~+150°C, +100~+550°C TP2:-20-+150″C,
+100-+400°C
(Supports Auto Switch)
---|---
Accuracy
| Reading accuracy of ±2% or ±2°C (whichever is greater) @ambient temperature of
-10-50″C.
Temperature Analysis
| Coldest And Hottest Points, Central Point, And Custom Measurements (Supports
3 Custom Points, 3 Custom Lines, 3 Custom Frames)
Emissivity Setting| 0.01-1.00
Connecting Solution| USB Type-C
Battery| 1050mAh
Charging Time| 1.5h
Charging Temperature
| 0-+40°C
(Do Not Charge The Device In
High-Temperature Environments Above 40°C Or In Low-Temperature Environments Below 0°C.)
Charging Solution| WiFi, USB Type-C
Battery Runtime| 2h, with Battery Indicator
Operating Temperature|
Storage Temperature|
Relative Humidity| 10%-90% (Non-Condensing)
IP Rating| IP54
Drop Rating| 2m
Certification| CE/FCC/RoHS/TELEC/DGM/TSCA/WEEE
Shock & Vibration| 2G (IECB00BB-2-6), 25G (IECB00BB-2-29)
Dimensions| 135.6mm x 41mm x 29.1mm
Net Weight| 125g
Contact Information
MileseeyTechnology (us) Inc.
- Office Add: 17800 CASTLETON ST STE 665 CITY OF INDUSTRY, CA 91748
- Manufacturer: Shenzhen Mileseey Technology Co., Ltd. Add: No.36Dl Block A, Tanglang Town Plaza West, Fuguang Community, Taoyuan Street, Nanshan District, Shenzhen, China
- Website: www.mileseey.net
- Store: www.mileseeytools.com
- E-mail: service@mileseey.com
- Made in China
- MILESEEY has started researching, developing, and manufacturing high-quality optical products including golf & hunting rangefinders, laser measure devices, and thermal & digital night visions since 2009.
- Focusing on development researching, and manufacturing for over 12 years, we strive to provide you with premium-quality products and satisfying customer service to make your life easier and smarter.
- MileseeyTechnology (us) Inc.
- Office Add: 17800 CASTLETON ST STE 665 CITY OF INDUSTRY, CA 91748
- Manufacturer: Shenzhen Mileseey Technology Co., Ltd. Add: No.3601 Block A, Tanglang Town Plaza West, Fuguang Community, Taoyuan Street, Nanshan District, Shenzhen, China
- Website: www.mileseey.net
- Store: www.mileseeytools.com
- E-mail: service@mileseey.com
- Made in China
FCC ID: 2AEOG-TP2PLUS
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Body Operation
This device was tested for typical body operations. To comply with RF exposure requirements, a minimum separation distance of 5mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any metallic components. Body accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or approved antenna. Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>