MILESEEY PFS2H Red Illustrated Display Hunting Rangefinder User Manual

May 15, 2024
MILESEEY

MILESEEY PFS2H Red Illustrated Display Hunting Rangefinder

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-
product

Product Overview

  • Thank you for purchasing the MILESEEY PFS2H laser rangefinder. Please read the instructions carefully before use.
  • MILSEEY PFS2H is a portable laser rangefinder for hunting, hiking, and other outdoor activities, providing precise range readings up to 1,000 yards, with up to ±1 yard accuracy.
  • Built with high-quality materials, PFS2H is lightweight, anti-slip, wear-resistant, and provides a comfortable gripping experience.
  • PFS2H adopts pulsed laser technology & time-of-flight(TOF) principle as well as state-of-the-art algorithms to measure the linear distance, vertical height distance, horizontal distance moving speed, etc.
  • PFS2H features high accuracy, quick response, intuitive display, and low power consumption. It is a perfect companion for outdoor activities.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(1\)

Safety instructions

  1. AWarning
    • When shooting the laser, please do not stare into the laser hole. Staring at the sun through this instrument may cause permanent damage to the eyes! Never point this instrument directly at the sun to avoid permanent damage to internal components. Avoid exposing the eyepieces to direct sunlight.MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig- \(2\)
    • Do not place the instrument under extreme temperature conditions exceeding the storage temperature of the instrument (the storage temperature of the instrument is -10~60°C).
  2. Disposal
    • Everyone is responsible for environmental protection.
    • It is strictly forbidden to dispose of waste batteries together with household garbage. Please dispose of waste batteries at designated garbage collection stations. This product cannot be recycled together with domestic waste. Please dispose of this product properly according to the regulations implemented in the country/region.
  3. Scope of Responsibility
    The company will not be responsible for any loss caused by using the rangefinder without following this manual, using third-party accessories, or modifying the rangefinder by yourself.

Battery installation and instructions

  1. Please use a 1xCR2 battery to power the device.
  2. When you see the flashing icon “ “, it is a low battery warning. Please replace the battery or it will affect the accuracy.
  3. Please take the battery out of the device if you are not going to use it for a long time.

Installation steps:

  1. Flip up the rotating handle on the battery cover and rotate anti-clockwise until the battery cover is opened (Fig.1; Fig.2).MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig- \(4\)
  2. Install 1 xCR2 battery, observing the correct polarity( Fig.3).
  3. When the battery assembly is completed, rotate the cover clockwise to tighten the battery cover(Fig.4; Fig.5).

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(6\)

Appearance

  1. Eyepiece knob
  2. Power/Measure button
  3. Mode/Display switch button
  4. Laser Emission lens
  5. Objective Lens/Laser receiving lens
  6. Slope switch (measuring modes can only be enabled when the slope switch turns on)
  7. Battery bin

Icons on LCD display

  1. Low battery indicator

  2. From left to right:
    Line of sight (Linear distance), unit(Y/M), object moving speed (Km/h)

  3. Crosshairs

  4. From left to right:
    BOW(Horizontal component distance) mode/Auto height, measuring data(auto height; HCD), unit(Y/M)

  5. Angle Indicator

  6. Rain & fog mode

  7. Vertical height (between two points)

  8. Hunting mode

Elementary operation and setting

Eyepiece adjustment
Rotate the eyepiece knob to fine-tune your vision.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(11\)

Unit Charge
When the rangefinder powers off, long-hold the mode button ; then short- press the power button to start up the device. The unit will simultaneously shift between Y and M. (note: do not release the press of mode button until your target unit is reached.)

Black & red display switch

  • Short press the power button to start up the device. Black text is the default display mode.
  • Long press the mode button to switch to red text display mode. Long press again to enhance red text brightness.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(12\)

Operation instructions

  1. Press the power button to start up the device.
  2. Adjust the eyepiece to focus on the target before measuring.MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig- \(13\)
  3. Rotate the red pointer of the slope switch to enable the mode switch.
  4. Short press to switch modes.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(14\)

In the course of the measurement, if the target reflection is weak or is beyond the measuring range, it will display as”—“. The measurement range will be affected by the materials of the target & visibility of the weather. In general, if the target surface is smooth with great reflectivity and the weather is good without fog, the measurement range will be longer.

Rain & Fog mode (last target priority)
This mode is mainly used to measure rain and fog conditions. Due to the influence of raindrops on rainy days, you may receive some invalid values caused by the raindrops. The last target mode helps the laser punch through moisture in the air to give you accurate distance readings by reporting the distance of the last target.

Short press the mode button to switch to rain & fog ranging mode (Last-target priority) . Aim at target B. Short press the measure/display button, and the last-target-priority algorithm will eliminate the invalid values caused by raindrops and other particles in the air, displaying the distance result of the last target on the upper line.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(16\)

Modes

BOW mode (horizontal component distance)

  • This mode is mainly used to measure the horizontal component distance(HCD) to the target object. It is applied to bow hunting or other short-range hunting where you don’t need bullet drop/holdover information.
  • Short press the mode button to switch to BOW mode (HCD) . Aim at the point B, and then short-press the measurement button. The linear distance (LOS) from the rangefinder to the target would be displayed on the upper line. The horizontal component distance(HCD) and the tilt angle will be displayed at the bottom of the LCD screen.MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig- \(18\)

Auto-height mode
Short press the mode button to switch to the auto-height mode . Aiming at point B, and short press the measurement button. The linear distance (LOS) from the rangefinder to the target would be displayed on the upper line. The height distance and the tilt angle would be displayed at the bottom of the LCD screen.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(19\)

Vertical height (between two points)
Short press the mode button to switch to vertical height mode . Aim at target B. Press to get the distance and angle (the angle between the linear distance and horizontal component distance) between A and B. Move to target C, and press to get the distance and angle (angle between the linear distance and horizontal component distance between A and C). The vertical height between Band C will be displayed on the upper line, and the absolute value of the difference between the two angles 8 will be displayed at the bottom.

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(21\)

Speed measuring mode

  • The speed measuring mode is to measure the moving speed of the game. “a”must be less than 10°. The smaller the angle, the higher the accuracy. Short press the mode button to switch to the speed measuring mode.
  • Aiming at target B. Press and hold the measure button  and move slightly until the speed is displayed.
  • Speed measurement range: 18~300km/h.MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig- \(22\)

Specification

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(23\)

Important Notice

  1. To protect the coating of the lens, do not touch the lens with your fingers.
  2. The laser rangefinder has been precisely calibrated by in-house developed instruments. Please send it back to the dealer for repair instead of disassembling by yourself.
  3. When the lens is contaminated, please wipe gently with a clean cloth. Do not use tough objects to wipe.
  4. Avoid collision or heavy load when carrying or using. Keep the device away from baking or corrosion.
  5. Keep the product away from moisture during storage. Please keep it in a dry, cool, and well-ventilated place to avoid direct sunlight, dust, and temperature mutation.
  6. Rain and fog will affect the laser beam path, which may affect the measurement accuracy.

Contact us

Mileseey Technology (US) Inc.

Copyrights
The product specifications are subject to change without notice, and all final interpretation rights are reserved by Mileseey Technology Co., Ltd., and all trademarks, product images, and technical parameters are properties of Mileseey Technology Co., Ltd., and all rights are reserved.

Warranty Card

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(24\)

Warranty Terms

Warranty Period

  • This product has a year warranty in the precondition of non-artificial damage.
  • Within the warranty period, certain maintenance costs will be charged under the following cases

MILESEEY-PFS2H-Red-Illustrated-Display-Hunting-Rangefinder-fig-
\(25\)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals