VOLLRATH T39731N Cafeteria Breath Guard Installation Guide
- August 8, 2024
- VOLLRATH
Table of Contents
VOLLRATH T39731N Cafeteria Breath Guard
Product Specifications
- Brand: Vollrath
- Model: One Piece and Three Piece Cafeteria Breath Guard
- Item No.: 2350030-01
Product Usage Instructions
One Piece Breath Guard Installation:
Install the breath guard uprights (A) to the studs (B) securing with cap
nuts (C) as shown in Figure 1. Repeat for all four uprights.
Three Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
Frequently Asked Questions
-
What should I do if I accidentally over tighten the cap nuts?
If you accidentally over tighten the cap nuts, stop immediately to prevent cracking of the plastic. Loosen the cap nuts slightly and then retighten them carefully. -
Can I install the breath guard without using all the components mentioned in the instructions?
It is recommended to follow the complete installation instructions to ensure proper assembly and stability of the breath guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
Three Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE:
Use caution when tightening the cap nuts. Overtightening may cause the plastic
to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
ABOUT COMPANY
- The Vollrath Company, L.L.C.
- 1236 North 18th Street
- Sheboygan, WI 53081-3201
- U.S.A.
- Main Tel: 800.628.0830
- Service Tel: 800.628.0832
- FAX: 800.752.5620
- Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
- http://www.vollrathco.com/