TOOLCRAFT 3030239 1400 W 4 In 1 Multi Purpose Vacuum Cleaner Instruction Manual

: August 7, 2024
: Toolcraft

TOOLCRAFT 3030239 1400 W 4 In 1 Multi Purpose Vacuum Cleaner

FAQ

Q: How do I clean the filters?

A: To clean the filters, gently remove them from their compartments and wash them with mild soap and water. Allow them to air dry completely before reinserting them into the vacuum cleaner.

Q: Can I use this vacuum cleaner on carpets?

A: Yes, this vacuum cleaner can be used on carpets. Adjust the suction power as needed to effectively clean different surfaces.

Operating Instructions

4-in-1 Multi-Purpose Vacuum Cleaner, 1400 W

Item no: 3030239

Introduction

Dear customer,
Thank you for purchasing this product.
If there are any technical questions, please contact: www.conrad.com/contact

Operating Instructions for download

Use the link www.conrad.com/downloads (alternatively scan the QR code) to download the complete operating in-structions (or new/current versions if available). Follow the instructions on the web page.

Intended use

The product is a 4-in-1 multipurpose vacuum cleaner that can be used in the following configurations:

Configuration	Description of use
Wet vacuum	■ Remove liquid from hard floors.

■ See section: Operation: wet vacuum [► 32].

Dry vacuum| ■ Remove dust, dirt, and small debris.

■ See section: Dry Vacuum [► 32].

Spray extraction cleaning| ■ Clean carpets or upholstery.

■ Utilizes the clean water tank with the option to add detergent.

■ See section: Spray extraction cleaning [► 29].

Blow-out| ■ Blow away leaves or debris from outdoor areas (e.g., pathways).

■ Inflating an air mattress.

■ See section: Blow-out [► 33].

Important:
Never use the product to vacuum up hazardous, toxic, combustible, or explosive substances.

This product is only authorized for use in dry rooms or in protected areas outdoors.
If you use the product for purposes other than those described, the product may be damaged.
Improper use can result in short circuits, fires, electric shocks or other hazards.
The product complies with the statutory national and European requirements.
For safety and approval purposes, you must not rebuild and/or modify the product.
Read the operating instructions carefully and store them in a safe place. Make this product available to third parties only together with the operating instructions.

Delivery contents

Motor unit
Collecction tank
Clean water/detergent tank
1x dust bag
1x foam filter
1x crevice nozzle
1x floor nozzle
1x spray nozzle (upholstery)
1x spray nozzle (floor / carpet)
1x short pipe (ø6mm)
1x long pipe (ø6mm)
1x suction hose with spray nozzle trigger
2x pipe clips
3x extension tubes
2x wheels
2x swivel castor hubs
2x swivel castors
1x handle
4x handle screws
Operating instructions

Description of symbols

The following symbols are on the product/appliance or are used in the text:

The symbol warns of hazards that can lead to personal injury.
The symbol warns of dangerous voltage that can lead to personal injury by electric shock.
This product must only be used in dry, enclosed indoor areas. The motor unit and power supply must not get damp or wet.
Protection class 2 (double or reinforced insulation, protective insulation).

Safety instructions

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

Read first!

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of ex-perience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Supervise children so that they do not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Disconnect the power plug from the socket outlet before assembling, disassembling, changing accessories, cleaning, or maintaining the appliance.

General

■ The product is not a toy. Keep it out of the reach of children and pets.
■ Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.
■ If you have questions which remain unanswered by this information product, contact our technical support service
or other technical personnel.
■ Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

Handling

■ Handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

Operating environment

Do not place the product under any mechanical stress.
Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam and solvents.
Protect the product from direct sunlight.

Operation

Consult an expert when in doubt about the operation, safety or connection of the product.
If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.

Mains cable

Do not modify or repair mains supply components including mains plugs, mains cables, and power sup-plies. Do not use damaged components. Risk of death by electric shock!

The mains outlet must be located near to the device and be easily accessible.
Never plug in or unplug the mains plug when your hands are wet.
Never pull the mains plug from the socket by pulling at the cable. Always pull it from the mains socket using the intended grips.
Unplug the mains plug from the mains socket if you do not use the device for an extended period of time.
Disconnect the mains plug from the mains socket in thunderstorms for reasons of safety.
Make sure that the mains cable is not squeezed, bent, damaged by sharp edges or put under mechanical stress.
Avoid excessive thermal stress on the mains cable from extreme heat or cold.
Do not modify the mains cable. Otherwise the mains cable may be damaged. A damaged mains cable can cause a deadly electric shock.
Do not touch the mains cable if it is damaged.
- First, power down the respective mains socket (e.g. via the respective circuit breaker) and then carefully pull the mains plug from the mains socket.
- Never use the product if the mains cable is damaged.
A damaged mains cable may only be replaced by the manufacturer, a workshop commissioned by the manufacturer or a similarly qualified person, so as to prevent any danger.
Ensure that cables are not pinched, kinked or damaged by sharp edges.
Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

Precautions for fine particulate matter

Do not vacuum fine particles (e.g., drywall dust, ash, concrete dust, plaster). Fine dust will not be captured by the cartridge filter and may damage the motor and / or clog the dust bag.
Fine particles can pass through the dust bag. Always operate the vacuum in well-ventilated areas and wear a suitable dust mask (if required).

Product

Do not block the air inlets and outlets during use.
Do not use the product without an inserted filter.
Do not use the product as a pump.
Do not vacuum sharp objects.
Never leave the product unattended during use.
Risk of overheating. Do not operate the product continuously for more than 40 mins. Switch the product OFF and allow to completely cool before resuming use.
The following items must not be vacuumed:
Burning matches or smouldering ashes and cigarette butts, or other hot or glowing/burning substances.
- Flammable, combustible or explosive substances, dusts, vapours, liquids.
- Hazardous, solvent-based or corrosive substances, dusts, vapours, and liquids.
In blow-out mode, never point the air flow at people or animals.
Risk of motor overload. Empty the dust filter and collection tank before it gets full.
Do not flip the product upside down with the motor unit connected.
The hose must not be stretched beyond its original length, bent excessively, crushed, dragged along the ground, or twisted.
The motor unit must never come into contact with water or high humidity during use, maintenance, cleaning, and storage.

Overview

Product

Switch: ON(I)/OFF(0)
Pipe outlet: Clean water/detergent tank
Locks
Air intake opening
Collection tank
Pipe: Clean water/detergent tank
Cap: Clean water/detergent tank
Clean water/detergent tank
Handle
Motor unit
Air outlet opening Parts
12 Suction hose
Extension tubes
Crevice tool
Floor nozzle
Foam filter
Handle
x Handle screws
spray nozzle (floor/carpet)
2x Wheels
spray nozzle (upholstery)
Short pipe (ø6mm)
Long pipe (ø6mm)
Pipe clips
2x swivel castor hubs
2x swivel castors 27 Dust bag (washable)

Initial assembly

Slide the swivel castor hubs into the slots, and then attach the swivel castors to the hubs. [1].
Attach the wheels to the hubs [3].
Attach the handle to the motor unit using the in-cluded screws [4].

Storage configuration

The product has integrated storage slots for parts.
Store any remaining items (e.g., hose and pipes) in the con-tainer.
Coil the power chord around the flange on top of the air outlet.

Spray extraction cleaning

Important

Do not fill the clean water/detergent tank with liquids ≥45 °C.
Risk of damage and/or health risks. Do not use harsh chemicals (e.g., bleach, solvents, chlorine).
Adding detergent to the clean water tank is not always required. Check if just using clean water is effective.
Use a detergent specifically designed for extraction cleaning.
Make sure the detergent is suitable for the surface being cleaned.
Always test the detergent solution on a small, inconspicuous area to make sure it does not cause discoloration or damage to the cleaning surface.

Parts used

Assembly

Connection

Attach the suction hose and connect the pipe to the pipe outlet.

Pipe fitting

Insert the pipe all the way into the fitting.
Slide the collar on the fitting to release the pipe.

Operation: spray extraction cleaning

Preconditions:

The dust bag is removed.
The foam filter is inserted.
The detergent / clean water tank is filled.

Switch the power ON.
à Suction will begin.
Squeeze the trigger on the suction hose handle to spray fluid from the detergent/clean water tank.
Switch the power OFF when finished.
Disconnect the product from the power supply.
Empty the collection tank, clean, and dry the product after each use. See section: Cleaning and maintenance .

Wet vacuum

Parts used

Assembly

Operation: wet vacuum

Preconditions:

The dust bag is removed.
The foam filter is inserted.
The detergent/clean water tank is disconnected.

Switch the power ON.
Suction will begin.
Switch the power OFF when finished.
Disconnect the product from the power supply.
Empty the collection tank, clean, and dry the product after each use. See section: Cleaning and maintenance.

Dry Vacuum

Parts used

Assembly

Operation: dry vacuum

Preconditions:

The dust bag is inserted.
The foam filter is inserted.
The detergent/clean water tank is disconnected.

Switch the power ON.
Suction will begin.
Switch the power OFF when finished.
Disconnect the product from the power supply.

Blow-out

Parts used

Assembly

Connect the hose to the air outlet opening on the back of the motor unit.
Experiment with different combinations of extension tubes and/or crevice tool to get the best result.

Operation: blow out

Preconditions:

The dust bag is inserted.
(Optional) the foam filter is inserted.
The detergent/clean water tank is disconnected.

Switch the power ON.
Blowing will begin.
Switch the power OFF when finished.
Disconnect the product from the power supply.

Troubleshooting

Problem	Suggested solution
Low suction power.	■ The motor unit is not placed / locked correctly on

the collection tank.

■ The dust bag is full. See: Empty the dust bag [► 35].

■ Check if there is a blockage.

■ Check the fittings are connected properly.

No detergent or not enough de- tergent being sprayed.| ■ Check the tank is not empty and/or the hose extends into fluid.

■ Check all the pipes are correctly fitted.

■ Check the pipe for blockages.

■ The detergent may be too viscous. Dilute with water or use another deter- gent.

Spray extraction jet is not steady.| ■ Check the nozzle for blockages.
Dust comes out of the motor unit| ■ The dust bag is damaged and must be replaced.

■ The dust bag is not properly sealed, check if the zip is closed.

Cleaning and maintenance

Important:

Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions. They damage the housing and can cause the product to malfunction.
Do not immerse the motor unit in water.

Cleaning the main unit

Disconnect the product from the power supply.
Clean the product with a fibre-free cloth. Lightly moisten if needed.
Make sure all ventilation openings are clear from debris. If needed, use a soft-bristled brush.

Cleaning after spray extraction
To avoid the buildup of detergent residue that can cause clogging, thoroughly rinse the pipes and allow to air dry after each use.

Preconditions

The product is set up for spray extraction cleaning. See: Spray extraction cleaning [} 29].

Remove the tank and rinse out all detergent residue.
Fill the tank with clean water.
Run the product with clean water to remove detergent residue from connected pipes.
Disconnect the tank and run the product to expel moisture from the pipes.
Disconnect the tank and pipes, and allow to completely air dry before storing away.

Empty the dust bag

Empty the dust bag in a well-ventilated environment, and always wear a dust mask.
Open the zip on the dust bag to empty it.

Maintenance

Important:
Any servicing of the motor unit must be carried out by a qualified professional.

Storage

After each use and before storage, observe the following (if applicable):

Empty dirt and debris.
Empty all water.
Rinse all detergent and water from the system. See Cleaning after spray extraction
Disconnect all accessories and allow to completely air dry.
Disconnect the clean water/detergent tank.

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU market. This sym-bol indicates that this device should not be disposed of as unsorted municipal waste at the end of its ser-vice life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point.

Distributors of electrical and electronic equipment are legally obliged to provide free take-back of waste. Conrad provides the following return options free of charge (more details on our website):

in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the ElektroG

End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Parts and accessories

Parts and accessories are available on www.conrad.com.
Search the item number for this product to find what is available.

Technical data

Input voltage …………………………………………. 220 – 240 V/AC
Input AC frequency ………………………………… 50/60 Hz
Power …………………………………………………… 1400 W
Suction power………………………………………… 18 kPa
Capacity………………………………………………… – Dust bag: 15.5 L
- Liquid tank: 14 L
- Clean water/detergent tank: 5 L
Sound pressure level………………………………. 80-85 dB(A)
Protection class ……………………………………… II
Ingress protection…………………………………… IPX4
Operating/storage conditions……………………. -20 to +50 °C, ≤80% RH (non-condensing)
Hose length …………………………………………… 1.5 m
Dimensions (Ø x H) ……………………………….. 38 x 58 cm
Weight (approx.) ……………………………………. 6.5 kg

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or the capture in electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication reflects the technical status at the time of printing.

Copyright by Conrad Electronic SE *3030239_V1_0524_dh_mh_en 1381955467-2 I1/O1 en