VIMAR 46KIT.036C Bullet Wi-Fi Camera User Guide

: August 6, 2024
: VIMAR

Table of Contents

VIMAR 46KIT.036C Bullet Wi-Fi Camera User Guide
Package content
Characteristics
Installation
WALL MOUNTING
Configuration
Operation disclaimer for Wi-Fi cameras
Conformity
WEEE – Information for users
Privacy
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VIMAR 46KIT.036C Bullet Wi-Fi Camera User Guide

Package content

Characteristics

Status light:
Blinking red light: wait for network connection (fast)
Solid blue light on: camera is working correctly
Solid red light on: network is malfunctional
Microphone:
Capture sound for your video.
Reset:
Press and hold for 5 seconds to reset the camera (if you
NOTE: sd card not supported.

Installation

Positioning

The series camera is in the integrated brackets structure. the basement of the camera at the installation location.
To loosen the camera body’s screws to adjust the three-axis. Adjust the connection between brackets and basement by axis to implement 0º~360º in the horizontal direction; Adjust the spherical joint of brackets can achieve 0º~90º in the vertical direction and 0º~360º in the rotational direction. Please tighten the screws after adjusting the camera image to the right scene. All the Installation has finished

WALL MOUNTING

Fix the camera to the wall with screws
Adjust camera angle to a suitable view (as shown in the picture)

Installation Notes: To prevent over-exposed images, avoid installing the camera under backlight or excessive light conditions.
Atter adjusting your camera angle, please lock the screw

Configuration

Power up the camera

Connect the power cable to the bipolar connector on the camera cable.
Connect the power supply to a wall socket.
Wait for the LED to hear spoken feedback (“Camera ON”and then“ Camera setup ”).

Adding a camera
Addition via QR Code: use the camera to scan the QR code displayed on NVR monitor.
Follow the instructions on the screen to complete installation and connection to your recorder.
To make this process easier, we recommend you stay close to your NVR recorder.

Click the QR code in the upper right corner of the monitor, take the camera and point it at the monitor to scan the QR code to add it.

A QR code will be displayed on monitor, turn camera to face the monitor at a distance of between 15 – 20 cm from the lens, a tone will be emitted after a few seconds.
Wait for connection to be completed, after a few seconds the device will be successfully added and the camera will complete the connection with the recorder.

NOTE: in case of connection failure, reset the camera with the RESET key and repeat the procedure of paragraph 4.2.
For more information see the complete manuals and updated available in the product sheet on the site: https://faidate.vimar.com/it/it

Camera Specifications

**Camera| – Image sensor| 3 Megapixel CMOS
–| 2304(H) x 1296(V)
– IR distance| **

Night visibility up to 10 m

**| Auto(ICR)/Color/ B/W
Lens| 3.6 mm 85°
Video and Audio| Encoding| H.264/H.265
Audio input/output| 1 MIC/1 SPEAKER integrati – included
Live| 25 fps
Network| Wi-Fi –| 2.4 GHz WIFI(IEEE802.11b/g/n)
| 2412-2472 MHz
| < 100 mW (20dBm)
*****General| Operating* temperature| -10 °C to 50 °C
Power supply| DC 12 V / 1 A
protection| IP65
| Ø 58 x 164 mm
Power supply Specifications**

Alimentatore

Power supply

Operation disclaimer for Wi-Fi cameras

The Wi-Fi camera allows images to be viewed on the buyer’s (hereinafter “Customer”) smartphone and / or tablet only if combined with the NVR 46NVR.04CW present in the kit 46KIT.036C, by simply installing the Vimar VIEW Product application.
The visualization of the images is allowed only through the presence, in the house / building in which it is installed, of a connection to a home Wi-Fi network with Internet access which must have the following characteristics:

IEEE 802.11 b / g / n (2.4 GHz) standard
Operating modes:
Networks: WEP, WPA and WPA2.
TKIP and AES encryption protocols are supported for WPA and WPA2 networks.
Do not support “hidden” networks (hidden SSID).

To use the service The Customer must have technical equip-ment that allows connection to the Internet and sign an agree-ment with an ISP (Internet Service Provider); this agreement may involve related costs. Vimar remains unaffected by the choice of technical equipment and the agreement with the ISP (Intemet Service Provider). The consumption of data through the use of the Vimar VEW Product App, both in the home / building and outside the Wi-Fi network that the Customer has used for installation, remains the responsibility of the Customer.

The interaction and correct operation remotely via the Vimar VIEW Product App, through the Internet network of your mobile phone /data provider, with the Wi- Fi camera installed by the Customer may depend on:

a) type, brand and model of the smartphone or tablet;
b) quality of the W-Fi signal;
c) type of the home intemet access contract;
d) type of data contract on the smartphone and tablet.

The camera supports connection via P2P technology, it is therefore necessary to check that your ISP (lntermet Service Provider) does not block it Vimar is exempt from any liability for any malfunctions due to non-compliance with the minimum technical specifications necessary for the operation of the product which are indicated above. To resolve any problems, refer to the complete manual and the “Questions and answers” section on the product page at the following Internet address: faidate. vimar.com.
Vimar reserves the right to modify the characteristics of the products shown at any time and without notice.

Conformity

RED directive. RoHS directive
Standards EN 301 489-17, EN 300 328, EN 62311, EN 62368-1, EN 55032, EN 55035, EN 61000-3-2, EN 61000-3-3, EN IEC 63000.
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text of the EU declaration of
-ware are on the product sheet available at the following Inter-net address: faidate.vimar.com

WEEE – Information for users

If the crossed-out bin symbol appears on the equipment or packaging, this means the product must not be included with other general waste at the end of its working life. The user must take the worn product to a sorted waste center, or return it to the retailer when purchas-ing a new one. Products for disposal can be consigned free of charge (without any new purchase obligation) to retailers with a sales area of at least 400m2, if they measure less than –
tally friendly disposal of the used device, or its subsequent
environment and people’s health, and encourages the re-use and/or recycling of the construction materials.

Privacy

Privacy Policy
As required by Regulation (EU) 2016/679 on the protection of personal data, Vimar S.p.A. guarantees that the electronic processing of data minimises the use of personal and other strictly necessary in order to achieve the purposes for which it was collected. The personal information of the Data Subject is processed in accordance with the product/application privacy policy available on our website www.vimar.com in the legal section (Product – App Privacy Policy – Vimar energia positiva).
Please remember that, pursuant to Regulation (EU) 2016/679 on the protection of personal data, the user is the controller of processing for the data collected during use of the products and, as such, is responsible for adopting suitable security measures that protect the personal data recorded and stored, and avoid its loss.
Should the products monitor public areas and not just private property, it will be necessary to display – in a visible manner – the information about the ‘area under video surveillance’ envisaged Data Protection Authority (Garante).

Images may be stored for 24 hours, and for up to 72 hours in the cases envisaged in the video surveillance measures issued by the Italian Data Protection Authority on 8 April 2010. In addition, the user must guarantee safe possession of and control over its passwords and the related access codes to its web resources. The Data Subject must provide the password for access to its system when requesting help from the Vimar Support Centre, so that the related support can be provided. Provision of the password represents consent for processing. Each Data Subject is responsible for changing the password for access to its system on completion of the work carried out by the Vimar Support Centre.’

Viale Vicenza, 14 36063 Marostica VI – Italy www.vimar.com