Pipishell PILTK4-N1 UL Listed Tilt TV Wall Mount Bracket Installation Guide

Pipishell PILTK4-N1 UL Listed Tilt TV Wall Mount Bracket

0 1-800-556-9829(US/CA)
44-808-196-3885(UK)
Email:   support@pipishell.net
Website: www.pipishellav.com

IMPORTANT SAFETY INFORMATION

[NOTE]

• Please carefully read all instructions before attempting installation. If you do not understand the instructions or if you have any questions or concerns, please call technical support or email customer service.
• Before starting assembly, verify that all parts are included and undamaged. Do not use damaged or defective parts. If you require replacement parts, please call technical support or email customer service.
• Not all hardware included in this package will be used.

[CAUTION]

• Avoid the risk of personal injury or property damage!
• Do not use this product for any purpose that is NOT explicitly specified in this manual. Do not exceed the maximum weight capacity. We are not liable for damage or injury caused by incorrect assembly, improper mounting, or inappropriate use.

[WARNING]

• This product is designed for installation on wood stud, solid concrete and brick walls. DO NOT install on drywall alone.
• The wall must be capable of supporting four times the weight of the TV and mount combined.
• This product contains small parts that may pose a choking hazard.

Note for Wood Stud Installation (Page 12-13)

• Avoid the risk of personal injury or property damage! Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a socket wrench.
• Do not use wall anchors for this mounting option. Wall anchors are used for solid concrete and brick wall installations only.
• Minimum wood stud size: 1 1 /2″ W x 3 1 /2″ D (38 x 89mm)
• Wood stud spacing: 16″ to 24″ (406mm to 610mm) (center to center)

Note for Solid Concrete or Brick Wall Installation (Page 14)

• Avoid the risk of personal injury or property damage! Tighten the lag screws only until they are pulled firmly against the wall plate (DO NOT overtighten). Do not use a drill; only use a socket wrench.
• Mount the wall plate directly on the concrete surface.
• Minimum solid concrete thickness: 8″ (203mm)
• Never drill into the mortar between bricks.

Before getting started, make sure this mount is compatible.

1. VESA Pattern Compatibility

2. If the TV weighs more than 132 lbs (60kg), do not use this product.

3. Suitable for installation on wood stud, solid concrete and brick walls.
   DO NOT install on drywall alone.
   NOTE: For steel stud installation, “SNAPTOGGLE” type bolts are required (not included).

4. Tools Needed (Not Included)

Supplied Parts and Hardware

CAHand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or MB) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole. UTION!
This anchor is for concrete or brick walls ONLY. DO NOT use them in drywall or wood studs

Step 1 Attach the TV Brackets to the TV
Select TV Bolts

Hand thread bolts into the threaded inserts on the back of your TV to determine which bolt (M4, M6 or MB) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.

Spacer and Bolt Configurations

Attach the TV Brackets to your TV

Option A: For Flat Back TVs

Option B: For Curved Back TVs

Spacers must be tall enough so that the curved back of the TV does not interfere with the mounting plate.

Option C: For TVs with a Bump

The TV brackets must be flush on the bump and leveled by spacers on the gap.

Option D: For TVs with Protruding Cables

Option E: For TVs with Recessed Holes

Step 2 Assemble the Wall Plate (Optional)
Option A)
16″ (406mm) wood stud spacing and TV VESA Pattern:
200 x 1 00mm-400 x 400mm

Option B
 18-24″ (457mm-610mm) wood stud spacing and TV VESA Pattern: 200 x 100mm-600 x 400mm

Step 3 Mount the Wall Plate or Wall Plate with Extender on the Wall
Option A: For wood studs, follow Page 12-13.
Option B: For solid concrete or brick walls, follow Page 14.

Use a stud finder to locate wood studs or use an awl to find the edges. Mark the edge and center locations.
Position the wall plate or wall plate with extender [03] & [04] at your desired height and line up the holes with your stud centerline. Level the wall plate [03] or wall plate with extender [03] & [04] and mark the holes.

NOTE: Be sure to drill into  the center of the studs.

Drill 4 pilot holes using a 5/32″ (4mm) diameter drill bit. Make sure the depth is NOT less than 2 3/8″ (60mm). Install the wall plate [03] or wall plate with extender [03] & [04] using the lag screws [A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.

Position the wall plate [03] or wall plate with extender [03] & [04] at your desired height. Level the wall plate and mark the pilot hole locations. Drill 4 pilot holes using a 3/8″ (10mm) diameter drill bit. Make sure the depth is NOT less than 2 3/5″ (65mm). NEVER drill into the mortar between bricks.

Use a hammer to tap the anchors [A2] into the wall. Be sure the anchors [A2] are seated flush with the concrete or brick surface. Mount the wall plate [03] or wall plate with extender [03] & [04] using the lag screws [A 1 ]. Tighten the lag screws [A 1] only until they are pulled firmly against the wall plate (DO NOT overtighten).

Step 4 Verify the Mount is Firmly Mounted on the Wall

Step 5 Set the Tilt Angle of the TV Brackets

Adjust the hooks on both TV brackets to the same desired angle. You may need to slightly loosen the tilt tension bolts [T]. Retighten tilt tension bolts [T] to secure the tilt angle. If you make the angle too large, the brackets may not flt over the wall plate.

Step 6 Hang the TV on the Wall Plate Assembly

1. Hang the TV with brackets on the wall plate.
2. Pull both cords [R] down to open the latches, then push them forward toward the wall. The latches should engage on the wall plate. Release the cords to lock the TV in place. If latches did not engage, pull the cords and try again.

Step 7 Remove the TV

To remove the TV, first disconnect all cables. Pull the cords [R] down and hold them while gently pulling the bottom of the TV away from the wall plate. Exerting too much force may cause the latches to break. Once the latches are free, lift the TV up and off of the wall plate.

Step 8 Tilt Adjustment

Tilt the TV to the desired angle. You may need to adjust the tilt tension bolts [T]. Do not overtighten or overloosen the bolts. If you cannot access the tilt tension bolts, you may need to remove the TV, adjust the tilt angle, then remount the TV.
1- 800-556-9829(US/CA)
44- 808-196-3885(UK)
Email: support@pipishell.net 
Website: www.pipishellav.com 

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>