Pipishell Medium Full-Motion Tv Wall Mount User Guide
- June 7, 2024
- Pipishell
Table of Contents
Pipishell Medium Full-Motion Tv Wall Mount User Guide
PIMFK1
Thank you for choosing our product! We strive to provide the best quality
and services for our customers. Would you kindly share your experience on
Amazon if you are satisfied? Should you have any issues, please don’t hesitate
to contact us.
Telephone：800-556-9829
Mon-Fri 10am – 6pm (PST) (USA)
Email：supportus@pipishell.net
(US/CA/DE/UK/FR/IT/ES/JP/AU)
WARNING!
SEVERE PERSONAL INJURY AND PROPERTY DAMAGE CAN RESULT FROM IMPROPER INSTALLATION OR ASSEMBLY. READ THE FOLLOWING WARNINGS BEFORE BEGINNING.
- If you do not understand the instructions or have any concerns or questions, please contact a qualified installer.
- Do not install or assemble if the product or hardware is damaged or missing. Not all parts and hardware included must be used. If you require replacement parts, contact customer service at supportus@pipishell.net
- This product has been designed for use on a vertical wall constructed of wood studs. Wood studs being defined as a wall consisting of i• minimum of 2″ x 4″ studs with a maximum of 1/2″ of wall covering (drywall, lath, plaster).For custom installations please contact a qualified installer. For safe installation, the wall you are mounting to must support 4 times the weight of the total load. If not, the surface must be reinforced to meet this standard. The installer is responsible for verifying that the wall structure/surface will safely support the total load.
Tools Needed (Not Included)
SUPPLIED HARDWARE
Step 1 Before TV Bracket Installation
75mm =2.95 in. 100mm =3.94 in.
200mm =7.87 in. 300mm =11.81 in.
400mm =15.75 in.
Measure the distance between the holes located at the back of your TV (these
measures may form the shape of a square, or a rectangle) and check that these
taken measures are within the VESA() range for this wall mount () VESA:
International standard established by the TV manufacturers used to determine
if LCD / LED TVs are compatible with wall mounts.
Please select the proper screw length for your TV by hand tightening to your
plat panel thread depth.
When attaching brackets to the flat screen, be careful not to over tighten
screws and be sure that screws do not bottom out in the mounting holes.
Install TV Bracket
Step 3A
CAUTION:
Ensure the wall plate is securely fastened to the wall before continuing on
to the next step:
These anchors are for concrete or brick walls ONLY. DO NOT use them in
drywall or wood studs.
Use a stud finder (not included)to locate wood stud. Mark the edge and center
locations.
3A-1
.
3A-2
**3A-3
**
Drill 4 pilots holes using a 1/5 in. (5.5) is not diameter drill hit. make
sure the depth less than 25/9 in.(65mm).
3A-4
Mount the wall plate using 4 sets of 23/8 in lag bolts A1 and washers
A2 with a 1/2 in socket wrench (not included)
Step 3B
CAUTIOIN: Ensure the wall plate is securely fastened to the wall befoe
continuing on to the next step
These anchors are for concrete or brick walls ONLY. DO NOT use them in
drywall or wood studs.
3B-1
Position the wall plate at your desired height, level the wall plate and
mark the polite hole locations.
3B-2
Drill 4 pilot holes using a 2/5 in. (10mm) diameter drill bit. make sure
the depth is not less than 2/8 in. (0mm)
**3B-3
**
STEP 4
Mounting your TV to the Brackets and lock it
Step 5 Post Installation level
if needed, the TV can be leveled +/-3 degrees
Step 6 Tilt adjustment
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>