Pipishell PIWFS02G Fireplace TV Stand with 18 Inch Fireplace Instruction Manual

PIWFS02G Fireplace TV Stand with 18 Inch Fireplace

Product  Specifications

Usage Instructions

• Operation
  To operate the electric fireplace, follow these steps
  Ensure that you have a 15 AMP circuit available for the appliance. Locate the main control panel at the top right corner on the front of the fireplace. Push the main switch down to the ON position to start the appliance. Use the power button on the control panel to turn the appliance ON or OFF. Use the heater button on the control panel to control the heat setting. The appliance comes with infrared quartz heating.

NOTE :  Adapters are not allowed for use in Canada.

A 15 AMP circuit is required to operate this appliance. If the breaker trips when the appliance is running, you may need to move the appliance to another location or unplug other appliances that are on the same circuit. The main control panel is located at the top right corner on the front Using the Control Panel

• Main Switch
  • Push button down to “ON” position to start.
  • Please ensure that the control panel is in the “ON” position. then you can push the heater button to start the related function.
  • Push button down to “OFF” position to shut down all functions.
• Heater Control

1. Push button down to start the heat setting.
2. Push second time to shut heater off.
3. This appliance comes with infrared quartz heating.

• Remote Control
  The electric fireplace includes a remote control for convenience. To use the remote control:

1. Ensure that the control panel on the product is in the OFF position.
2. Push the on/off button on the remote control to turn on or turn off the fireplace insert.
3. All functions will be restored at the next power on.

• Maintenance
  

WARNING: Before attempting to perform any maintenance on this appliance, turn all controls to the “OFF” position and then unplug. Allow the appliance to be “OFF” for at least 10 minutes before performing any maintenance in order to allow all components to cool properly.

• Replacing Light Bulbs

1. Ensure that all controls are off, the appli-ance is unplugged and bulbs are cool for touch.
2. Wear latex gloves to ensure that grease/oil from your hands does not transfer to the bulbs.
3. Remove 3 screws on the bulb panel.
4. Remove the bulb panel (Figure 4B).
5. You will see two 40W light bulbs below the log set. (Figure 4C)
6. Remove the burnt out light bulb and replace with a new bulb. WARNING: DO NOT EXCEED THE RECOMMENDED BULB WATTAGE. Hand tighten the bulbs only – do not over tighten.

• Place the bulb panel to the original position and tighten the back panel by 3 screws
• Cleaning
• • To remove lamp cover from back cover, use clean dry cloth.
    • To remove fingerprints or other marks from glass window, use clean damp cloth. Do not spray glass cleaner or other liquids directly onto the window.
    • Clean metal surfaces with a clean damp cloth making sure not to push dust or debris into any air intake or exhaust vents.
    • Do not use abrasive cleaners or spray liquids on any part of the appliance.
    • Periodic cleaning/vacuuming of the fan/heater unit is strongly recommended to ensure that no dirt or foreign objects build up.

When you first turn the heater on, it may emit a slight but harmless odor. This odor results from certain oils or greases being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly – it will not reoccur after the first operation of the appliance.
NOTE: This appliance comes equipped with an overheat protection safety device. Should the appliance begin to overheat for any reason, it will automatically turn all functions of the appliance off. The appliance will have to be reset prior to continuing use. To reset the overheat protection safety device, turn all controls off and unplug the appliance. Wait 10 minutes, plug the appliance back in and turn on.

FAQ

Q: What should I do if the breaker trips when the appliance is running
A: You may need to move the appliance to another location or unplug other appliances that are on the same circuit.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: Any use of this appliance other than that recommended by the manufacturer in this owners manual may cause fire, burns, electric shock and/or other serious injuries or death. When using electrical appliance, basic precautions should always be followed to avoid the risk of fire, electric shock and injury to persons including the following:

1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surface. If provided, use handles when moving this appliance. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains, etc. at least 3 feet (0.9 meter) away from the front of the appliance. Keep all items away from the sides and rear of the appliance.
3. Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the appliance is left operating unattended.
4. Always unplug appliance when not in use. This unit should be operate under supervision and should not be left on without supervision.
5. Do not operate any appliance with a damaged cord or plug or after any malfunction, or if it has been dropped or damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical adjustment or repair.
6. Do not use for outdoors.
7. This appliance is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate appli-ance where it may fall into a bathtub or other water container.
8. Do not run cord under carpeting. Do not cover the power cord with throw rugs, runners, or similar floor coverings. Arrange cord away from traffic area where it may pose a tripping hazard.
9. To disconnect the appliance, turn all controls “OFF”, then remove the plug from the electrical outlet.
10. Connect to properly grounded outlets only.
11. Do not insert or allow foreign objects to enter any ventilation or exhaust openings as this may cause an electric shock or fire, leading to damage or injury.
12. To prevent a possible fire, do not block air intakes or exhausts in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
13. All electrical appliances have hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.
14. Use this appliance only as described in this manual. Any other use which is not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
15. Itrongly recommended that to use the entire 15 amp outlet for the electric fireplace only. Sharing the outlet with another electronic item could create overload and damage the outlet and electric items in the long term.
16. Avoid using an extension cord because the extension cords may overheat and cause a risk of fire. However, if an extension cord MUST be used, the cord must be No. 14AWG minimum size and rated not less than 1875 Watts. The extension cord must be a 3-prong cord with grounding type plug and cord connection and should not exceed 20” (6m) in length.
17. When transporting or storing the appliance, keep both the unit and power cord/plug dry, free from excessive vibra-tion and away from heat sources to avoid causing fire, electric shock, or injury to persons.
18. Do not attempt to burn wood or other materials in this appliance.
19. This appliance, when installed must be electrically grounded in accordance with the current.

Canada: CSA C22.1, Canadian Electrical Code
U.S.A. : ANSI/NFPA NO. 70, National Electrical Code

PACKAGE CONTENTS

This heater includes a remote control. See below for directions to use the remote control

The remote control comes preassembled with a working battery and a insulation plastic film. Please remove the insulation plastic film from the battery before start using the remote control. Please replace the battery in remote control with correct battery type showing on back of remote control when the remote control does not work. Light bulbs may become loose during shipping. If the simulated flame effect is dim or does not operate properly at first, please ensure that the light bulbs are properly secured in the sockets (bulbs should be finger tight – do not over tighten). When you first turn the heater on, it may emit a slight but harmless odor. This odor results from certain oils or greases being heated as the appliance is used for the first time. This odor is perfectly safe and will stop shortly – it will not reoccur after the first operation of the appliance.
NOTE: This appliance comes equipped with an overheat protection safety device. Should the appliance begin to overheat for any reason, it will automatically turn all functions of the appliance off. The appliance will have to be reset prior to continuing use. To reset the overheat protection safety device, turn all controls off and unplug the appliance. Wait 10 minutes, plug the appliance back in and turn on.

TROUBLE SHOOTING

WARNING : Turn off the appliance, unplug and let cool for at least 10 minutes before attempting to service. Only a qualified professional should attempt to service or repair the appliance.

Simulated Flame Effect is dim or not presented.

|

1.  Light bulbs are burnt out.

2.  “lame wand” has come loose from bracket.

3.  “lame wand” motor is not functioning.

|

1. Inspect light bulbs and replace if necessary. (see Maintenance section of this manual)

2. Pls. refer “Replacing light bulbs” Fig 4A~Fig 4C to remove light bulbs first, Check the inside of firebox to secure end of “Flame wand” back into the support bracket.

The appliance turns off and will not turn back on.

|

1.  The overheat protection device in the appliance has been triggered.

2.  House circuit breaker has been tripped.

| 1.  Turn all controls off, unplug the appliance, allow the insert to cool down for at least 10 minutes, and then plug in and restart.

2.  Reset house circuit breaker.

The appliance does not turn on when the button is pushed to “ON”.

|

The overheat protection device in the appliance has been triggered.

|

Turn all controls off, unplug the appliance, allow the insert to cool down for at least 10 minutes, and then plug in and restart.

NOTE: If you experience difficulties, please do not return this product to store. Any missing parts, hardware or assembly problems, please contact Customer Service Center.
Warning: Any changes or modifications to this unit not expressly approved by the party responsi-ble for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc-tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is con-nected.
• Consult the dealer or an experienced radio/TV technician for help.

ONE YEAR LIMITED WARRANTY

The following non-transferable limited warranty applies is extended only to the original consumer-purchaser of this product. This product is only warranted against defects in material and workmanship subject to the normal and reasonable use and correct installation of the product for a period of one (1) year from the date of purchase. This warranty is made to the original owner, provided that the purchase was made through an authorized supplier of the company. Any unauthorized repair, alteration, misapplication, careless handling, improper installation, willful abuse, accident, or misuse of the product shall nullify this warranty. This warranty does not apply to the normal wear and tear. This warranty does not cover light bulbs. The duration of all implied warranties on this particular purpose are limited to the one (1) year duration of the express warranty period specified above. In no event will we be liable for any incidental or consequential damages (including loss of profits) arising from the use of this product. Some jurisdictions do not allow limitations on how long an implied warranty lasts, or do not allow the limitation or exclusion of incidental or consequential damages, so these implied warranty limitations may not apply to you. This limited warranty gives you specific legal rights. You may also have other rights which vary from jurisdiction to jurisdiction. Repair or replacement, at option, of a defective product is your sole remedy under this limited warranty. In no event will maximum liability exceed the purchase price of the product paid by the consumer/purchaser. If replacement parts are needed or to obtain performance of any obligation under this limited warranty, contact Customer Service Center. Be prepared to provide evidence of purchase date, proof of purchase, model number, and date code of your product, part number and defective part. Register your product within ten days to ensure your warranty. You must pay all expenses incurred in obtaining performance of any obligation under this limited warranty, including transportation, postage, and other incidental service costs. If defective part or parts are requested by Customer Service Center, you must make the product available to us free and clear of all liens and other encumbrances. We reserve the right to change prices, specifications and designs and to discontinue models without notice and without incurring obligations. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, might cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
The Remote Control requires 1 Lithium Coin Cell Battery (size CR2025), which is included.

• DO NOT mix old and new batteries.
• DO NOT use rechargeable silver oxide cell batteries with remote control unit.
• DO NOT mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium) batteries.
• DO NOT dispose of batteries in fire. Improper disposal may cause batteries to leak or explode.

Electric Fireplace
(US / CA) 1-800-556-9829 (UK) 44-808-196-3885

support@pipishell.net

www.pipishellav.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>