GE APPLIANCES GTDX200GM Capacity Electric Dryer Instructions

: July 31, 2024
: GE Appliances

Table of Contents

GTDX200GM Capacity Electric Dryer
Specifications
Product Usage Instructions
Installation Requirements
Venting Instructions
Special Installation Requirements
- FAQ
Q: Can I use this dryer with LP gas?
Q: How far should the dryer wall outlet be from the service
Q: What should I do if I need more information on venting

GTDX200GM Capacity Electric Dryer

“`html

Specifications

Model: GE GTDX205GM0CC
Electric Rating: 120V, 60Hz, 6A
Gas (BTU/HR): 22,000
Exhaust Option: Rear, left, and bottom 3-way
exhaust

Product Usage Instructions

Installation Requirements

Ensure the dryer is properly grounded and connected to a
dedicated circuit with the correct power rating. Gas supply
requires a conversion kit for LP gas. Exhaust the dryer to the
outside following safety guidelines provided in the manual.

Venting Instructions

Use metal ducts for exhaust and ensure proper termination of the
exhaust duct to prevent hazards. Do not terminate exhaust into
enclosed spaces or common ducts.

Special Installation Requirements

Comply with the National Electric Code and National Fuel Gas
Code for safe installation. Refer to the installation instructions
provided with the dryer for detailed information.

FAQ

Q: Can I use this dryer with LP gas?

A: Yes, the dryer is factory-equipped for natural gas but can be
converted to LP gas with a conversion kit installed by a qualified
technician.

Q: How far should the dryer wall outlet be from the service

cord entry?

A: The dryer wall outlet must be located within 36 inches of the
service cord entry and be easily accessible when the dryer is in
position.

Q: What should I do if I need more information on venting

kits?

A: For more information on venting kits and accessories, please
call 1-800-GE-CARES.

“`

This Owner’s Manual is provided and hosted by Appliance Factory Parts.
GE GTDX205GM0CC Owner’s Manual
Shop genuine replacement parts for GE GTDX205GM0CC
Find Your GE Dryer Parts – Select From 3387 Models ——– Manual continues below ——–

GTDX200GM/GTDX205GM
GE® 6.0 cu. ft. capacity DuraDrumTM gas dryer
Dimensions and Installation Information (in inches)
Exhaust Option: When viewed from the front of the unit, exhaust 3-way via rear, left and bottom. Dryer is shipped exhausted to the rear. Alternate exhausting knockouts are supplied.
Gas: An individual, properly-grounded branch circuit, with a three-prong groundingtype receptacle, protected by a 15 or 20 amp circuit breaker or a time-delay fuse is required.
Gas Dryer Electric Rating: 120V, 60Hz, 6A
Gas (BTU/HR): 22,000. Factory-equipped for natural gas. Tested for LP gas. LP gas supply requires a conversion kit. Check installation instructions for correct kit and have a qualified gas technician install a conversion kit. See dryer ducting information for proper installation.
Note: Dryer wall outlet must be located within 36″ of service cord entry and accessible when dryer is mounted in position.
Installation Information: For complete information, see installation instructions packed with your dryer.
For answers to your Monogram,® GE ProfileTM or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.

23-1/2 25-3/4

*24-1/

25-1/

25-1/2*

4-3/4 36 4

Side View

Sp

GTDX200GM/GTDX205GM
GE® 6.0 cu. ft. capacity DuraDrumTM gas dryer

For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4″ diameter all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semirigid) ducting can be used (Kit WX08X10077). In special installations, it may be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct. A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4″ diameter can be maintained throughout the entire length of the transition duct. Please see installation instruction packed with your dryer for complete instructions when using flexible metal (foil type) ducting.
Exhaust Length Calculation: 1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4″ rigid (aluminum or galvanized) duct which can be tolerated is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the duct length should be treated as a 90° elbow. A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed house floor (crawl space), or into an attic, since the accumulated lint could create a fire hazard or moisture could cause damage. Never terminate the exhaust into a common duct or plenum with a kitchen exhaust, since the combination of lint and grease could create a fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird nesting, etc. The wall cap must also be located at least 12″ above the ground or any other obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE- CARES.

Special Installation Requirements
Alcove or Closet Installation: · If your dryer is approved for installation in an alc
on the dryer back. · The dryer MUST be exhausted to the outside. · Minimum clearances between dryer cabinet an
0″ either side; 3″ front and rear · Minimum vertical space from floor to overhead · Closet doors must be louvered or otherwise ve
of 60 sq. in. of open area equally distributed. If a dryer, doors must contain a minimum of 120 · No other fuel-burning appliance shall be install
Bathroom or Bedroom Installation: · The dryer MUST be exhausted to the outdoors. · The installation must conform with the local co
with the National Electric Code and National Fu
Minimum Clearances other than Alcove or Clos · Minimum clearances to combustible surfaces a
Dryer Exhausting Information: Use metal duct

A A
4
B
Domestic 2-1/2 dryer models
7.0, 6.0 and 5.8 cu. ft. capacity models all gas dryers

Best pe
Maximu dia. rigid
Exhaust

Number of 90°
turns
0 1 2 3

A 4″ openin
90 ft. 60 ft. 45 ft. 35 ft.

Sp

GTDX200GM/GTDX205GM
GE® 6.0 cu. ft. capacity DuraDrumTM gas dryer
Features and Benefits · Auto Dry – Monitors air temperature with an automatic thermostat
and ends the cycle when clothes are properly dried · Rotary electromechanical controls – Easy-to-use controls make
it simple to set cycles · 4 heat selections – Provide the right temperatures for your
clothes-drying needs · Dewrinkle cycle – Special cycle is designed to help eliminate wrinkles
from a variety of fabrics · Quick FluffTM – Delivers ready-to-go results in minutes with no heat · Delicates cycle – Low-heat setting helps protect heat- sensitive fabrics,
like microfiber and rayon or nylon · Interior dryer light – Convenient interior light helps you easily
see clothes · Up to 90 ft. venting capability – Has long equivalent ducting
performance for more flexible installation · Model GTDX205GMCC Bisque on Bisque · Model GTDX200GMWW White on white
Sp