FKM6016D Digital Clamp Meter User Manual

: June 1, 2024
: FKM

Table of Contents

FKM6016D Digital Clamp Meter
Specifications:
Product Usage Instructions:
Electric Shock Hazard Warning:
Overview:
- FAQ:
Q: How do I switch between different measurement modes?
Q: Can this product be used for testing diodes?
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

FKM6016D Digital Clamp Meter

“`html

Specifications:

Model No.: FKM6016D
Measurement Units: % mV, V A nF, FmF, k, M, Hz, kHz, MHZ
Features: Automatic range mode, Voltage test mode, Current test
mode, Frequency test mode, Buzzer, Resistant measurement, DIODE
TEST MODE, Capacitance test mode, Current Am test mode, Temperature
mode, NCV test mode, Fire live test mode, Auto power off indicator,
Data hold on NCV and fire live indicator, DC AC, Relative value,
Percentage (duty cycle), MV, volts (voltage), Ampere (current),
Nafala, microfarads, cents Farah Ohm, kilohm, megohm (resistance),
Hertz, kilohertz, megahertz (frequency)

Product Usage Instructions:

Electric Shock Hazard Warning:

An electric shock hazard exists in current clamp measurements.
Follow these steps to ensure safety:

Hold the trigger and test lead the clampA wire line is measured
clip in the meter.
Read the current value displayed on the LCD.
Avoid clamping two or more wires of the circuit under test
simultaneously.
For accurate results, do not test two or more wires at the same
time.
Conduct measurements when the relative humidity is less than
75% for accurate readings.

Overview:

The product offers a wide range of measurement modes and
features for various testing needs. Make sure to follow safety
precautions and guidelines provided in the manual.

FAQ:

Q: How do I switch between different measurement modes?

A: Use the mode selector button on the device to switch between
voltage test mode, current test mode, frequency test mode, and
other available modes.

Q: Can this product be used for testing diodes?

A: Yes, the product includes a DIODE TEST MODE for diode
testing. Follow the instructions in the manual for proper diode
testing procedures.

“`

Model No. FKM6016D

% mV, V A nF,FmF
, k, M
Hz, kHz MHZ

Automatic range mode Voltage test mode Current test mode Frequency test mode Buzzer Resistant measurement DIODE TEST MODE Capacitate test mode Current Am test mode Temperature mode NCV test mode Fire live test mode Auto power off indicator Data hold on NCV and fire live indicator DC AC Relative value Percentage (duty cycle) MV, volts (voltage) Ampere (current) Nafala, microfarads, cents Farah Ohm, kilohm, megohm (resistance) Hertz, kilohertz, megahertz (frequency)
07

of the current clamp. 4″ ” Represents the maximum input ac current of 600 A. 5Please hold the clamp head when the current measurement machine to open the clamp head and nose pliers head clip conductor under test, and then slowly let go of the trigger, until the clamp head closed completely, please be sure to test whether the conductor is picking up in the middle of the tong head, not in the tong head center will produce additional error, clamp table can only measure electrical conductor, a conductor if two or more current is measured at the same time, the measuring reading will be wrong. 6) the Auto mode of AC current need bigger than 0.8A, if the AC current is smaller, need change to manual test mode 4.8 DC Current measurement
Warning An electric shock hazard. In current clamp measurements before the test probe is removed from the instrument. 1Hold the trigger and test lead the clampA wire line is measured clip in the meter. 2Read the current value in the LCD display Noted: 3The correct measurement results cannot be obtained by
clamping two or more wires of the circuit under test at the same time. 4To test two or more than two wires in same time, that cannot get correct resolute 5In order to obtain accurate readings, the conductor
15

Catalogue 1. Safety information 1.1 Preparation 1.2 Use 1.3 Mark 1.4 Maintenance 2. Description 2.1 Instructions 2.2 Button and Jacket 2.3 LCD display 3. Specifications 3.1 Overview 3.2 Technical indicators 4.O perations Guide 4.1 Data keep 4.2 Torch 4.3 Auto power off 4.4 Measurement 4.5 NCV 4.6 Live fire test 4.7 AC Current measurement 4.8 DC Current measurement 4.9 Voltage measurement 4.10 Resistant Measurement 4.11 Diode Measurement 4.12 Frequency Measurement 4.13 Temperature Measurement 5. Maintenance 5.1 Replace the battery 5.2 Replace the test leads 6. Accessories

……………01 ……………01 ……………02 ……………03 ……………03 ……………04 ……………04 ……………04 ……………06 ……………08 ……………08 ……………09 ……………12 ……………12 ……………12 ……………12 ……………13 ……………13 ……………14 ……………14 ……………15 ……………16 ……………17 ……………18 ……………18 ……………19 ……………19 ……………19 ……………20 ……………20

3. Specifications The instrument shall specify one yearduring 18¥ j 28¥
aThe relative humidity is less than 75% under the conditions of re calibration. 3.1 Overview
Automatic measurement and manual measurement Overload protection The maximum voltage allowed between the measuring terminal and earth600V DC or 600V AC DisplayLCD Maximum5999 display Polar indicationAutomatic indicator-‘,Display negative Over range display0L’ or `-0L’b Sampling time: about 3 times / sec Display unit and power display Automatic power off15Minutes Open Jaw is 26mm; test Line OD less than23mm Input static Current: less than 85mA Battery type1.5V AAA*3 Battery voltage indicationLCD Symbol Temperature coefficientless 0.1 operating temperature18¥ j 28¥ Storage temperature-10¥ j 50¥ Size184.0×66.0×34.8mm Weightabout 220gcIncluding battery 3.2 Technical indicators Environment temperature23±5¥ Relative humidity<75%
08

under test should be placed as far as possible in the center

of the current clamp. 4″ ” Represents the maximum input ac current of 600 A. 6Please hold the clamp head when the current measure

ment machine to open the clamp head and nose pliers head

clip conductor under test, and then slowly let go of the

trigger, until the clamp head is closed completely, please be

sure to test whether the conductor is picking up in the

middle of the tong head, not in the tong head center will

produce additional errors, clamp table can only measure

electrical conductor, a conductor if two or more current is

measured at the same time, the measuring reading will be

wrong.

the Auto mode of AC current needs bigger than 0.8A, if the

AC current is smaller, needs change to manual test mode

4.9 Voltage measurement

Warning

An electric shock hazard.

When the measurement of high voltage, please pay

special attention to avoid electric shock

Do not enter the effective value of voltage higher than

AC600V

1)Press the button longer than 2 seconds. At this time, the

meter is in Auto voltage measurement;

Use black test lead inserted into the COM socket, the red

test lead is inserted into the

socket,

Test lead will link the voltage source and load to test 4Read the voltage value on the LCD

16

1. afety Instructions This instrument strictly follow GB/T 13978-92 Generic
specification for Digital Clamp meter, Following GB4793.1-1995 cIEC-61010-1, IEC-61010-2-032Electronic measuring instruments safety requirementsBelong to the two class of pollutionVoltage standard CAT III 300V and CAT II 600V
This model is a 3 5/6 Smart digital clamp meter. It can be used to measure AC and DC voltage, DC current, resistance, capacitance, frequency, temperature, diode and on-off test, fire live test, NCV function with function symbol, data holding, auto power off and backlight lighting functions. The instrument has compact structure, safety jacket, which is easy to operate and easy to carry. It is an ideal tool for electrical measurement.
Please follow the safety instructions, ensure the safety of the use of the instrument. use and protect the item in right condition, the instrument will be in satisfactory service. 1.1 Preparation 1.1.1 user must comply with the standards of safety rules
when use it – Protection against electric shock – To prevent the misuse of the instrument 1.1.2 After receiving instrument, check whether the damage in transit. 1.1.3 Check and confirm the meter whether damaged or not after shipment,
01

3.2.1 AC Current

Range 60A 600A

Resolution 0.01A 0.1A

Accuracy 2.5% + 8
3.0% + 10

-Input Min Current: 0.8mA AC

– Input Max Current: 600A AC – Frequency50Hz -60Hz

– When AC current is measured, the meter automatically opens

an internal low-pass filter to filter out high-frequency current.

3.2.2 DC current:

Range 60A 600A

Resolution 0.01A 0.1A

Accuracy c2.5% + 5 c3.0% + 8

3.2.3 DC voltage

Range 600mV 6V

Resolution 0.1mV 0.001V

Accuracy 0.8% + 5 0.5% + 3

60V 600V

0.01V 0.1V

1.0% + 5

– Input Min voltage0.6V AC -Maximum/ input voltage600V AC cEffective valueOR

600V DC – Frequency40Hz -1000Hz

09
notice: 1when the measured signal is greater than or equal to 0.61v, the meter will display the dc voltage of course measured; When the measured signal is less than 0.61v, the meter will default to the resistance value and display the internal resistance value of the measured signal. 2″ “show the maximum input voltage is 600V AC or 600V DC. 3 If the instrument measures more than 600V AC, issued an alarm 4) Also can select auto and manual test mode manually 4.10 Resistance test
Warning The risk of electric shock In the measurement of impedance on the line, should be determined to disconnect the power supply circuit, capacitor circuit completely discharge. 1)Press the button longer than 2 second. At this time, the meter is in Auto voltage measurement; 2) Use black test lead is inserted into the COM socket, the red test lead is inserted into the socket, 3) Test lead will link the voltage source and load to test 4
In the measurement of low resistance, in order to measure accurately, please short-circuit the two test leads, otherwise if the test short-circuit is bigger than 0.61V, the meter will think that is Voltage test mode Notice: 1
if measured resistance value is bigger than 60M, the LCD
17

1.1.4 Test leads must be in good condition. Check the insulation test is damaged, the wire conductor is bare before use,
1.1.5 Use the test leads to ensure safety; they must bereplaced with the same or similar rank test if necessary.
1.2 Use 1.2.1 Use the correct function and range. 1.2.2 Do not exceed the scope of protection of the range of
the indicating value measurement. Do not exceed the scope of protection of the range of the indicating value measurement 1.2.3 When measuring circuit, do not touch the test lead tip (metal parts). 1.2.4 In the measurement, if the measured voltage is higher than 60V DC or 30V AC (RMS), attention should be paid to keep your fingers always after the test finger protection device. 1.2.5 If the voltage between the measuring end and the earth is more than AC 600V, don’t measure the voltage. 1.2.6 Before turning the switch changes the measurement function, should be removed test lead from the circuit 1.2.7Don’t live line measurement of resistance, diode and continuity test 1.2.8Under the test ranges of current, resistance, diode and continuity test, it should be taken to avoid the instrument connected voltage source. 1.2.9 Do not use this instrument in the gas, steam or dust 1.2.10If you notice any abnormal or faulty instruments,
02

3.2.4 AC voltage

Range 600mV 6V

Resolution 0.1mV 0.001V

Accuracy 1.0% + 8 0.8% + 5

60V

0.01V

600V

0.1V

1.2% + 5

– Input Min voltage0.6V AC

-Maximum/ input voltage600V AC cEffective valueOR

600V DC – Frequency40Hz -1000Hz

3.2.5 Frequency

Range 99.99Hz

Resolution 0.01Hz

Accuracy 0.5% + 2

999.9Hz

0.1Hz

9.999kHz

0.001kHz

99.99KHZ

0.01kHZ

999.9KHZ

0.1kHZ

Overload protection250V DC or ACcEffective value – Input range 200mV~10VPPcEffective valueWith the

increase of the measured frequency, the input voltage should be increased

3.2.6 Capacitance

Range 60nF

Resolution 0.01nF

Accuracy ±(3.0% of reading +5words

600nF

0.1nF

6uF

0.001uF

60mF

0.01mF

±(3.0% of reading +5words)

600mF

0.1m F

10

will display “OL”over range status 2
If the measured resistance value is less than 50, the meter will buzz alarm 3
If the measured resistance value is less than 1M, the instrument may take a few seconds to stable reading, it is normal for high resistivity readings 4
When testing the on line resistant, please discharge the capacitate and all power shut off to make sure the test value correct. 4.11 capacitance test
Warning Risk of electric shock. To avoid damage to the meter or the device discharged capacitance before measuring 1) Press button switch to capacitance test status 2) Black test lead is inserted into the COM socket, the red test lead is inserted into the socket 3) Discharge the capacitance and link the capacitance to test 4) Display readings on LCD Notice: 1
In order to improve the less than 10 nF test accuracy, should be minus the meter and line capacitance. 4.12 Frequency test
Warning Risk of electric shock. To avoid damage to the meter or the device under test, all power to the circuit under test should be cut off and all high voltage capacitors fully discharged before measuring
18

should stop using 1.2.11 unless the instrument bottom shell and the battery
cover is fastened in situ; it should not use the instrument. 1.2.12 Do not store or use the instrument in direct sunlight,
high temperature, high humidity conditions. 1.3 Mark
Note (safety information,is important see instructions Can be used for dangerous live conductor Double insulation protectioncII CAT III In accordance with theIEC-61010-1Over voltage standard level (installation) IIIaThe pollution degree of 2 refers to the pulse voltage protection levels. In line with European standards (EU) Grounding 1.4 Maintenance 1.4.1 Please do not attempt to test lead the shell to adjust or repair instrument, this operation can only be fully understood by technicians 1.4.2 Before test leading the instrument bottom shell and the battery cover should be removed the test lead from the measured line test lead 1.4.3 TO avoid false readings may cause electric shock, when the instrument display ” ” symbol The battery should be replaced immediately. 1.4.4 Use a damp cloth and a mild detergent to clean the instrument; do not use abrasive detergents or solvents. 1.4.5 The instrument when not in use should turn off the power,
03

6mF

0.001mF

±(5.0% of reading +5words

60mF

0.01mF

100mF

0.1mF

Not calibrated

3.2.7 Temperature test

Range

Accuracy

Resolution

20300

±(2.5%+5d)

1

3011000

±(2.5%+5d)

1

-4600

±(2.5%+5d)

1

6011832

±(2.5%+5d)

1

– Overload protection: 250V DC or AC (rms)

3.2.8 Resistance

Range

Resolution

Accuracy

600

0.1

±(1.2% + 2)

6k

0.001k

60k

0.01k

600k 6M

0.1k 0.001M

±(2.0% + 5

60M

0.01M

– open-circuit voltageAbout 0.4V

– Overload protection600V DC or ACcEffective value

3.2.9 Continuity test

Range

Resolution

Function

If the measured line

0. 1

resistance is less than 50, enclosing the instrument

may sound a buzzer

– Overload protection600V DC or ACcEffective value

11

the resistance.

Press button switch to frequency status
Black test lead is inserted into the COM socket, the red test

lead is inserted into the

socket

Test lead will link the voltage source and load to test
Display readings on LCD

The test range is 10HZ-10MHz, if test frequency is less than

10Hz, the display show “00.00” ,if larger than , When using this

function, don’t insert test leads

4.13 Temperature Measurement

Warning

Do not enter a temperature higher than 60V AC voltage

30V AC voltage to avoid damage or instrument damage

Press button switch to temperature status
Black test lead is inserted into the COM socket, the red test

lead is inserted into the

socket

The other end of the K-type thermocouple (test side) close to

the surface of the measured object.

To be read by the liquid crystal display to read the measured

temperature value.

Note:

K-type thermocouple distribution of the highest measurement

temperature of 250

5. Maintenance

5.1 Replace the battery

Warning

Before opening the instrument of the battery cover, please

removed the test leads from measuring circuit so that to

19

1.4.6 If you do not use a meter-long time, the battery should be removed to prevent damage to the instrument.
2. Description – The instrument is a professional measuring instrument
with liquid crystal display and a back light source. The user readings easily. Single hand operation with overload protection and low battery indicator. For professional, factory, school, lovers or family use, is an ideal Multi- function instrument. – Used for AC DC voltageaAC current, frequency, resistance, capacitance measurement and the on-off circuit, measurement, temperature measurement . – Automatic range – Data keep – Auto power off – Relative measurement 2. Part name Ò Current clamp head: For current measurement Ó The torch of head lamp Ô Panel Õ LCD Monitor Ö Power button × Common socket Ø Resistor, voltage Diode and Continuity, fire live, frequency, capacitance, temperature test input jack (8Data hold and Torch (9) Select function change between Resistor, voltage Diode and Continuity (10) Alarm light: Continuity NCV and High voltage alarm
04

3.2.10 Diode test

Range

Resolution

Function

1mV

Show the approximate diode

forward voltage value – Overload protection600V DC or ACcEffective value

4. Operations Guide

4.1 Data keep

In the process of measurement, such as the need to keep reading, push keyThe display value will be locked, then press the button so that relieve readingb

4.2 Torch

Press long than 3 second, then open the torch. Press

again then close the torch. Torch cannot close automatically

need close manually.

Torch is LED, long time on will decrease the battery life,

please use the torch for short time and close the torch in time. If the battery and voltage are not enoughcabout3.6V

The LCD display” “symbol, at this time , if you use Torch ,

the current is big so you should not replace the battery. If you

do not use the Torch , the LCD show ” “, you should replace

the battery.

4.3 Automatic power off 1Without operation after 15 minutes The meter will

enter the sleep state automatically shut down to save power.

1 minute before the shutdown, each 1 minutes the buzzer 1

sound prompt, dormant into a long sound after that before

the shutdown.

4.4 Measurement

12

avoid the risk of electric shock. 1) if ” “symbol displayplease replace the batteryb

Unscrew fastening screws of the battery cover and move

away.

replace the old battery

notice:

The battery polarity cannot be reversed

5.2 Change Test Leads

Warning

Please use the same test leads or same level test

leads

if you need replace to the test leads . the test leads

level: 1000V 10A.

If one damaged insulation, such as wire exposed, must be

replaced.

6. Accessories

1Test lead

level1000V 10A

one

2Manual

one

3battery

1.5V AAA

two

The contents of this manual are subject to change without

notice

The contents of this brochure are believed to be correct, if

users find errors, please contact the manufacturer. The company is not responsible for the accident and harm

caused by user wrong operation * This manual describes the function, not for other special use

20

(11) NCV light
05
1Toggle the switch and open power, If the battery and voltage Is not enoughcabout2.4V The LCD display” “symbol then the battery should be replaced
2” “symbolThe input voltage or current should not exceed the value indicated, this is to protect the internal circuit from being damaged.
3Connect the public test line, and then connected test line is When in wiring, The test should be removed first line charged dismantling wiring.
4) when power is on, the meter has not entered to test mode, will enter to scan mode, then can press enter to related test mode
5) At any test mode, Press enter to auto testing mode 4.5 NCV (Non-contact voltage test) Press button, When clamp head close to mains phase line or power switch, socket the detected voltage is close to the 110V AC RMS

the indicator will change from green to green +yellow When the induction voltage is higherthe indicator will change to green +yellow+ red ,With buzzer alarm more intensive and indicator will shine high frequency
Warning Even if no indication but the voltage may still exist. Don’t rely on non-contact voltage detector to determine whether there is a voltage shielded wire. The operation may affect the detection by socket design, insulation thickness and different types
13
Warranty Please show your product certification when you need repair service or something wrong with items, it is effective show one and purchase invoice in together 1Please contact with our company or repair service department when your clamp meter appears faults as soon as possible, don’t delay your use and warranty period. 2Our company provides warranty service for one year from the date of purchasebThe company provides free warranty service after professional confirms the problem is not by user sabotage during the warranty period 3Repair need charges (repairs components fee) more than the warranty period 4All of the following will charge the cost of repair even in the warranty period. ÒImproper use or accidental disasters caused damage of components and circuit board burn ÓNon-professional personnel open shell, check and modification ÔDo not follow the instructions to operation caused problems ÕNo maintenance and repair of the other company products Öusers offer the maintenance of postage and transportation fees ×Clamp meter’s battery, probe, temperature probe and other functional accessories not included free warranty list
21

2.3 LCD display

06

4.6 Firing live Measurement