TESLA RS0880H Larder User Manual

: June 3, 2024
: Tesla

TESLA RS0880H Larder

SAFETY INFORMATION

In the interest of your safety and to ensure the correct use, before installing and ﬁrst using the appliance, read this user manual carefully, including its hints and warnings. To avoid unnecessary mistakes and accidents, it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features. Save these instructions and make sure that they remain with the appliance if it is moved or sold, so that everyone using it through its life will be properly informed on appliance use and safety.

For the safety of life and property keep to the precautions of these user instructions as the manufacturer is not responsible for damages caused by omission.

Children and vulnerable people safety

This appliance can be used by children aged of 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge if they have supervision or have been given instructions concerning the use of the appliance in a safe way and understand the hazards involved.
Children aged from 3 to 8 years are allowed to load and unload this appliance.
Children should be supervised to ensure that they do not play with the appliance.
Cleaning and user maintenance should not be done by children unless they are aged from 8 years and above and supervised.
Keep all packaging well away from children. There is risk of suffocation.
If you are discarding the appliance pull the plug out
of the socket, cut the connection cable (as close to the appliance as you can) and remove the door to prevent playing children from suffering electric shock or closing themselves in.
If this appliance features a magnetic door seal to replace an older appliance having a spring lock (latch) on the door or lid, be sure to make that spring lack unusable before you discard the old appliance. This will prevent it from becoming a death trap for a child.

General safety

Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use other electrical appliances (such as ice cream makers) inside of refrigerating appliances, unless they are approved for this purpose by the manufacture.
Do not touch the light bulb if it has been on for a long period of time because it could be very hot.1
When positioning the appliance, ensure the supply cord is not trapped or damaged.
Do not locate multiple portable socket-outlets or portable power suppliers at the rear of the appliance.
Do not store explosive substances such as aerosol cans with a ﬂammable propellant in this appliance.
The refrigerant isobutene (R600a) is contained within the refrigerant circuit of the appliance, a natural gas with a high level of environmental compatibility, which is nevertheless ﬂammable.
During transportation and installation of the appliance, be certain that none of the components of the refrigerant circuit become damaged.
- avoid open ﬂames and sources of ignition
- thoroughly ventilate the room in which the appliance is situated
It is dangerous to alter the speciﬁcations or modify this product in any way. Any damage to the cord may cause a short circuit, ﬁre and/or electric shock.
This appliance is intended to be used in a household and similar applications such as
- staff kitchen areas in shops, ofﬁces and other working environments;
- farm houses and by clients in hotels, motels and other residential type environments;
- bed and breakfast type environments;
- catering and similar non-retail applications.

Any electrical components (plug, power cord, compressor and etc.) must be replaced by a certiﬁed service agent or qualiﬁed service personnel.

The light bulb supplied with this appliance is a “special use light bulb” usable only with the appliance supplied. This “special use lamp” is not usable for domestic lighting.1

Power cord must not be lengthened.
Make sure that the power plug is not squashed or damaged by the back of the appliance. A squashed or damaged power plug may overheat and cause a ﬁre.
Make sure that you can come to the main plug of the appliance.
Do not pull the main cable.
If the power plug socket is loose, do not insert the power plug. There is a risk of electric shock or ﬁre.
You must not operate the appliance without the lamp.
This appliance is heavy. Care should be taken when moving it.
Do not remove nor touch items from the freezer compartment if your hands are damp/wet, as this could cause skin abrasions or frost/freezer burns.
Avoid prolonged exposure of the appliance to direct sunlight.

Daily use

Do not put hot things on the plastic parts in the appliance.
Do not place food products directly against the rear wall.
Frozen food must not be re-frozen once it has been thawed out. 2
Store pre-packed frozen food in accordance with the frozen food manufacture, s instructions. 2
Appliance, s manufactures storage recommendations should be strictly adhered to. Refer to relevant instructions.
Do not place carbonated of ﬁzzy drinks in the freezer compartment as it creates pressure on the container, which may cause it to explode, resulting in damage to the appliance.2
Ice lollies can cause frost burns if consumed straight from the appliance.2

To avoid contamination of food, please respect the following instructions

Opening the door for long periods can cause a signiﬁcant increase of the temperature in the compartments of the appliance.
Clean regularly surfaces that can come in contact with food and accessible drainage systems.
Clean water tanks if they have not been used for 48h; ﬂush the water system connected to a water supply if water has not been drawn for 5 days.
Store raw meat and ﬁsh in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
Two-star frozen-food compartments (if they are presented in the appliance) are suitable for storing pre-frozen food, storing or making ice-cream and making ice cubes.
One-, two- and three -star compartments (if they are presented in the appliance) are not suitable for the freezing of fresh food.
If the appliance is left empty for long periods, switch off, defrost, clean, dry and leave the door open to prevent mount developing within the appliance.

Care and cleaning

Before maintenance, switch off the appliance and disconnect the main plug from the power socket.
Do not clean the appliance with metal objects.
Do not use sharp objects to remove frost from the appliance. Use a plastic scraper. 2
Regularly examine the drain in the refrigerator for defrosted water. If necessary, clean the drain. If the drain is blocked, water will collect at the bottom of the appliance. 3

Installation

For electrical connection carefully follow the instructions given in speciﬁc paragraphs.
Unpack the appliance and check if there are damages• For electrical connection carefully follow the instructions given in speciﬁc paragraphs.
Unpack the appliance and check if there are damages on it. Do not connect the appliance if it is damaged. Report possible damages immediately to the place you bought it. In that case, retain packing.
It is advisable to wait at least four hours before connecting the appliance to allow the oil to ﬂow back in the compressor.
Adequate air circulation should be provided around the appliance, lacking this leads to overheating. To achieve sufﬁcient ventilation, follow the instructions relevant to installation.
Wherever possible the spacers of the product should be against a wall to avoid touching or catching warm parts (compressor, con- denser) to prevent possible burn.
The appliance must not be located close to radiators or cookers.
Make sure that the main plug is accessible after the installation of the appliance.

Service

Any electrical work required to do the servicing of the appliance should be carried out by a qualiﬁed electrician or competent person.
This product must be serviced by an authorized Service Center, and only genuine spare parts must be used.

Energy saving

Do not put hot food in the appliance;
Do not pack food close together as this prevents air circulating;
Make sure food does not touch the back of the compartment(s);
If electricity goes off, do not open the door(s);
Do not open the door(s) frequently;
Do not keep the door(s) open for a long time;
Do not set the thermostat on exceeding cold temperatures;
All accessories, such as drawers, shelves balconies, should be kept there for lower energy consumption.
1. If there is a light in the compartment.
2. If there is a freezer compartment.
3. If there is a fresh-food storage compartment.

OVERVIEW

REVERSE DOOR

Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.

Ensure the unit is unplugged and empty.
To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid so that it will not slip during the door reversing process.
All parts removed must be saved to do the reinstallation of the door.
Do not lay the unit ﬂat as this may damage the coolant system.
It’s better that 2 people handle the unit during assembly.

Remove the top right hinge cover.
Move the core cover from left side to right side. And then lift the upper door and place it on a padded surface to prevent it from scratching.
Undo the screws.Then remove the hinge bracket.
Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.
Remove the top left screw cover.
Reﬁt the bracket ﬁtting the bottom hinge pin.
Replace both adjustable feet.
Put the hinge cover and the screw cover back.
Put the hinge cover and the screw cover back.
Place the door back on. Ensure the door is aligned horizontally and vertically so that the seals are closed on all sides before ﬁnally tightening the top hinge.
Insert the hinge bracket and screw it to the top of the unit.
Use a spanner to tighten it if necessary.
Detach the Fridge and the Freezer door gaskets and then attach them after rotating.

INSTALLATION

Install door external handle (if external handle is present)

Space Requirement

Keep enough space of door open.
Keep at least 50mm gap at two sides and back.

Levelling the unit
To do this adjust the two levelling feet at front of the unit. If the unit is not level, the doors and magnetic seal alignments will not be covered properly.

Positioning
Install this appliance at a location where the ambient temperature corresponds to the climate class indicated on the rating plate of the appliance: For refrigerating appliances with climate class:

extended temperate: this refrigerating appliance is intended to be used at ambient temperatures ranging from 10 °C to 32 °C (SN);
temperate: this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 32 °C (N);
subtropical: this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 38 °C (ST);
tropical: this refrigerating appliance is intended to be used at ambient temperatures ranging from 16 °C to 43 °C (T);

Location
The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. Ensure that air can circulate freely around the back of the cabinet to ensure best performance. If the appliance is positioned below an overhanging wall unit, the minimum distance between the top of the cabinet and the wall unit must be at least 50 mm. Ideally, however, the appliance should not be positioned below overhanging wall units. Accurate leveling is ensured by one or more adjustable feet at the base of the cabinet. This refrigerating appliance is not intended to be used as a built-in appliance.

WARNING: It must be possible to disconnect the appliance from the mains power supply; the plug must therefore be easily accessible after installation.

Electrical connection

Before plugging in, ensure that the voltage and frequency shown on the rating plate correspond

DAILY USE

to your domestic power supply. The appliance must be grounded. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not grounded, connect the appliance to a separate grounder in compliance with current regulations, consulting a qualiﬁed electrician. The manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with the E.E.C. Directives.

Temperature setting recommendation

Environment Temperature	Freezer compartment	Fridge compartment

Summer

|

/

|

Set on 3~4

Normal

|

/

|

Set on 3~4

Cold

|

/

|

Set on 2~3

Information above give users recommendation of temperature setting.

Impact on Food Storage

Under Recommended setting, the best storage time of fridge is no more than 3 days.
The best storage time may reduce under other settings.

Daily use
Position different food in different compartments according to be below table

First use

Cleaning the interior
Before using the appliance for the ﬁrst time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand new product, then dry thoroughly

IMPORTANT: Do not use detergents or abrasive powders, as these will damage the ﬁnish.

Temperature Setting

Plug on your appliance. The internal temperature is controlled by a thermostat. There are 6 (8)settings. 1 is warmest setting and 5 (7)is coldest setting and 0 is off.
The appliance may not operate at the correct temperature if ii is in a particularly hot or if you open the door often.
This refrigerating appliance is not suitable for freezing foodstuffs.

Accessories

Movable shelves
The walls of the refrigerator are equipped with a series of runners so that the shelves can be positioned as desired.

Helpful hints and tips
Hints for fresh food refrigeration To obtain the best performance:

Do not store warm food or evaporating liquids in the refrigerator
Do cover or wrap the food, particularly if ii has a strong ﬂavour

Hints for refrigeration

Useful hints

Make (all types): wrap in polythene bags and place on the glass shelves above the vegetable drawer.
For safety, store in this way only one or two days at the most.
Cooked foods, cold dishes, etc … : these should be covered and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly cleaned and placed in the special drawer(s) provided.
Butter and cheese: these should be placed
in special airtight containers or wrapped in aluminum foil or polythene bags to exclude as much air as possible.
Milk bottle: these should have a cap and should be stored in the balconies on the door.
Bananas, potatoes, onions and garlic, if not packed, must not be kept in the fridge.

Cleaning
For hygienic reasons the appliance interior, including interior accessories, should be cleaned regularly.

CAUTION: The appliance may not be connected to the mains during cleaning. Danger of electrical shock! Before

cleaning switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker or fuse. Never clean the appliance with a steam cleaner. Moisture could accumulate in electrical components, danger of electrical shock! Hot vapors can lead to the damage of plastic parts. The appliance must be dry before it is placed back into service.
Important: Ethereal oils and organic solvents can attack plastic parts, e.g. lemon juice or the juice form orange peel, butyric acid, cleanser that contain acetic acid.

Replace the lamp

Do not allow such substances to come into contact the appliance parts.
Do not use any abrasive cleaners
Remove the food from the freezer. Store them in a cool place, well covered.
Switch the appliance off and remove the plug from the mains, or switch off or turn out the circuit breaker of fuse.
Clean the appliance and the interior accessories with a cloth and lukewarm water. After cleaning wipe with fresh water and rub dry.
After everything is dry place appliance back into service.

CAUTION: Before replacing the lamp, shall disconnect the appliance from mains power supply.

Lamp speciﬁcation is listed in rating label. Follow below process to replace the lamp:

Set the temperature regulation knob at number “O” to switch off the appliance.
Unplug the appliance to make sure the appliance is disconnected from main power supply.
Remove the screw of the lamp cover.
Pull the lamp cover out.
Unscrew the lamp.
Fit new lamp according to the opposite direction, then replace the lamp cover and screw.
Plug in the appliance and regulate the knob to right position.

TROUBLESHOOTING

CAUTION: Before troubleshooting, disconnect the power supply. Only a qualiﬁed electrician of competent person must do the troubleshooting that is not in this manual.
IMPORTANT: There are some sounds during normal use (compressor, refrigerant circulation).

Appliance does not work

| Temperature regulation knob is set at number “0”.| Set the knob at other number to switch on the appliance.
---|---|---
Power plug is not plugged in or is loose| Insert power plug.
Fuse has blown or is defective| Check fuse, replace if necessary.
Socket is defective| Socket malfunctions are to be corrected by an electrician.

The food is too warm.

| Temperature is not properly adjusted.| Please look in the initial Temperature Setting section.
Door was open for an extended period.| Open the door only as long as necessary.
A large quantity of warm food was placed in the appliance within the last 24 hours.| Turn the temperature regulation to a colder setting temporarily.
The appliance is near a heat source.| Please look in the installation location section.
Appliance cools too much|

Temperature is set too cold.

| Turn the temperature regulation knob to a warmer setting temporarily.

Unusual noises

| Appliance is not level.| Re-adjust the feet.
The appliance is touching the wall or other objects.| Move the appliance slightly.
A component, e.g. a pipe, on the rear of the appliance is touching another part of the appliance or the wall.| If necessary, carefully bend the component out of the way.
Water on the floor| Water drain hole is blocked.| See the Cleaning and Care section.
Side panels are hot.| It’s normal. Heat exchange parts are in the sides.| Take gloves to touch sides.

Environment Protection
This appliance does not contain gasses which could damage the ozone layer, in either its refrigerant circuit or insulation materials. The appliance shall not be discarded together with the urban refuse and rubbish. The insulation foam contains ﬂammable gases: the appliance shall be disposed according to the appliance regulations which can be obtained from your local authorities. Avoid damaging the cooling unit, especially the heat exchanger. The materials used on this appliance marked by the symbol are recyclable.

The symbol on the product or on its packaging
indicates that this product may not be treated as household waste. Instead it should be taken to the appropriate collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.

Packaging materials

The materials with the symbol are recyclable.
Dispose the packaging in a suitable collection container to recycle it.

Disposal of the appliance

Disconnect the mains plug from the mains socket.
Cut off the mains cable and discard it.

WARNING: During using, service and disposal the appliance, please pay attention to symbol similar as left side, which is located on rear of appliance (rear panel or compressor) and with yellow or orange color.

It’s risk of ﬁre warning symbol. There are ﬂammable materials in refrigerant pipes and compressor. Please be far away ﬁre source during using, service and disposal.

PRODUCT INFORMATION SHEET

COMMISSION DELEGATED REGULATION (EU) 2019/2016

with regard to energy labelling of refrigerating appliances

Overall dimensions (millimetre)

| Height| 850|

Total volume (dm³ or l)

|

88

16

| Maximum ambient temperature (ºC), for which the refrigerating appliance is suitable|

38

Winter setting| No|
Compartment Parameters:

Compartment type

| Compartment parameters and values

Compartment volume (dm³ or l)

| Recommended temperature setting for optimised food storage (ºC) These settings shall not contradict

the storage conditions set out in Annex IV, Table 3

|

Freezing capacity (kg/24h)

|

Defrosting type (auto- defrost=A, manual defrost=M)

Pantry| No| –| –| –| –
Wine storage| No| –| –| –| –
Cellar| No| –| –| –| –
Fresh food| Yes| 88,0| –| –| M
Chill| No| –| –| –| –
0-star or icemaking| No| –| –| –| –
---|---|---|---|---|---
1-star| No| –| –| –| –
2-star| No| –| –| –| –
3-star| No| –| –| –| –
4-star| No| –| –| –| –
2-star section| No| –| –| –| –
Variable temperature compartment| –| –| –| –| –
Light source parameters:
Type of light source| LED
Energy efficiency class| –
Minimum duration of the guarantee offered by the manufacturer: 24 months
Additional information:
Weblink to the manufacturer’s website, where the information in point4(a) Annex of Commission Regulation (EU) 2019/2019 is found: tesla.info

Link to the EU EPREL database
The QR code on the energy label supplied with the appliance provides a web link to the registration
of this appliance in the EU EPREL database. Keep the energy label for reference together with the user manual and all other documents provided with this appliance.

It is possible to ﬁnd information related to the performance of the product in the EU EPREL database using the link https://eprel.ec.europa.eu and the model name and product number that you can ﬁnd on the rating plate of the appliance.

For more detailed information about the energy label, visit www.theenergylabel.eu.

EU DECLARATION OF CONFORMITY

We, Comtrade Distribution d.o.o. Beograd, Bulevar Zorana Đindića 125i, 11 000 Belgrade, Serbia, hereby declare that the following refrigerator products listed below to which this declaration relates

Name of manufacturer: Tesla/Comtrade Distribution d.o.o. Beograd
Contact information of the manufacturer: Bulevar Zorana Đindića 125i 1 1000 Belgrade, Serbia

Description of the appliance

Tesla Code

RSO880H
RS0906H
RC2600H
RB5210FHX
RC2600HX
RB4300FHX
RB4300FHB
RM4700FHB
RU1700H
RI2500H
RM3400FHX1

Are in conformity with the following standards:

PIB: 100000104 Matični
broj: 17172140 Sifra
delatnosti: 2620

TEKUCI RACUN: UniCredit Bank RSD 170-300346515.65; Vojvodanska banka a.d. Novi Sad RSD 325-9500600009876-07
OTP Banka Srbija a.d. Beograd RSD 275.000220006014-70; Komercijalna banka RSD 205-147443-79

The construction of the appliances are in compliance with EU regulations and in accordance with the following harmonized standards:

LVD