TESLA Model 3 2022 AMD SR DIY Premium Audio Upgrade Installation Guide

Model 3 2022 AMD SR DIY Premium Audio Upgrade

Product Information: Model 3 2022 AMD SR DIY Installation Manual

The Model 3 2022 AMD SR DIY Installation Manual is a guide for installing a harness upgrade for the Tesla Model 3 2022 AMD SR. The manual provides detailed instructions on how to install the product, including a wiring harness, to improve the functionality of the vehicle. The manual also includes warning messages, warm prompts, and aftersale service contact information for users.

Product Usage Instructions

Before installing the product, please follow these steps:

1. Turn off the power on Tesla screen.
2. Disconnect the negative pole of 12V power supply at the frunk.
3. Disconnect the high-voltage gray plug under the right side of the rear seat.

Note: Failure to follow these steps may cause window lifting fault, door fault, or screen fault code.

To install the product, follow these steps:

1. Turn off the host power in the vehicle setting.
2. Remove the negative pole of the small battery on the Frunk.
3. Open the rear seat cushion and unplug the power plug.
4. Remove screws and buckles from the guard board on the front passenger foot socket, and then remove the guard board.
5. Remove the knee pad at the front passenger position.
6. Connect the black plug in the penultimate row to plug (small 16pin – label 4).
7. On the right side of the foot socket under the A-pillar of the front right seat, find the main plug of the right door and connect it to No plug (label 5).
8. Connect the Plug to the blue front surround plug under the left position of the A-pillar socket of the front left seat (Label 7).
9. Connect the left tweeter plug of harness Plug under the left foot socket of front left A-pillar to the main plug of the right door (Label 6).

Note: The red line refers to the wiring harness routing position. From the driver cap to the trunk, there are plugs that need to connect on ABC area. See the schematic diagram for details.

Warning: Please do not disassemble any part by yourself, any improper operation will not be covered by our warranty. If the vehicle is found to have inoperable fault or other serious fault, please contact Tesla’s after-sales department for maintenance. In order to avoid Tesla blaming the problems on the installed products, please remove the products first, and then go to Tesla’s after-sales department for maintenance. Otherwise, if not remove the products, Tesla will charge maintenance fees, which shall be borne by yourself.

If there are any differences between the installation instructions and actual operation, please follow the actual situation or contact aftersale service at +86 15622782181 (whatsapp/phone).

Note:

1. The installation instructions may differ slightly from the actual operation. If there are any differences,please follow the actual situation or contact us.
2. Warning: Please do not disassemble any part by yourself,any improper operation will not be covered by our warranty.

Warm Prompt

• If the vehicle is found to have inoperable fault or other serious fault, pls contact Tesla’s after-sales department for maintenance.
• In order to avoid Tesla blaming the problems on the installed products, please remove the products first, and then go to Tesla’s after-sales department for maintenance.
• Otherwise, if not remove the products, Tesla will charge maintenance fees, which shall be borne by yourself.

Note : Before installing the product, please do the following steps:

1. Turn off the power on Tesla screen;
2. Disconnect the negative pole of 12V power supply at the frunk;
3. Finally, disconnect the high-voltage gray plug under the right side of the rear seat. Otherwise, it will cause window lifting fault, door fault, or screen fault code.

Installation steps

Before installing the product, please turn off the power supply on the screen first, then disconnect the gray DCDC plug under the right rear seat, and then disconnect the negative pole of the battery in the frrunk. Otherwise, it will cause window lifting fault, door fault, or screen fault code.

The red line refers to the wiring harness routing position. From the dirver cap to the trunk, There have plugs need to connect on ABC area. See the schematic diagram for details Remove the knee pad at the front passenger position, connect the black plug in the penultimate row to plug ④(small 16pin – label 4) On the right side of the foot socket under the A-pillar of the front right seat, find the main plug of the right door and connect it to No plug ⑤ (label 5) Connect the Plug ⑦ to the blue front surround plug under the left position of the A-pillar socket of the front left seat (Label 7) Connect the left tweeter plug of harness Plug ⑥ under the left foot socket of front left A-pillar to the main plug of the right door (Label 6)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>