somfy Izymo Zigbee Motor Receiver Instructions
- July 30, 2024
- somfy
Table of Contents
somfy Izymo Zigbee Motor Receiver
Specifications
- Product: IZYMO MOTOR RECEIVER Zigbee
- Manufacturer: SOMFY ACTIVITES SA
- Compliance: FCC Part 15, Industry Canada’s license-exempt RSSs
Safety and liability
Liability
These instructions must be kept by the user. Failure to follow these
instructions or use of the product outside its field of application is
forbidden and will invalidate the warranty and discharge Somfy of all
liability. This Somfy product must be installed by a professional drive and
home automation installer. Moreover, the installer must comply with the
standards and legislation currently in force in the country in which the
product is being installed, and inform his customers of the operating and
maintenance conditions for the product. Never begin installing without first
checking the compatibility of this product with the associated equipment and
accessories. If in doubt when installing this product and/or to obtain
additional information, contact a Somfy representative or visit the website
www.somfy.com.
Safety instructions
- Never use the product if it is not correctly installed and placed inside a connecting box in conformity with the current norms.
- Do not use or install this product outdoors.
- If used with a motor, you should also consult the instructions provided with the motor.
- Keep the product out of the reach of children.
- Do not knock or drop the product, expose it to flammable materials or sources of heat or moisture, or splash or immerse it. Keep the product far away from liquids.
- Caution: danger of electrocution
- Before any installation make sure the power supply is disconnected to avoid any risk of electrocution.
- Directly cut the power supply from the breaker box to avoid any risk of electrocution. This product is designed to be used power up, a wrong installation can create a fire or an electric shock.
This product must be installed and connected carefully following these instructions. Cut the power supply before any operation and don’t do any modification if the LED is still on.
Product description
The IZYMO MOTOR RECEIVER Zigbee receiver is a radio micro receiver designed
for use in home automation systems operated under Zigbee protocols. It enables
the control of a roller shutter motor, an indoor or outdoor blind, or a
terrace awning, via a smartphone or Somfy Tahoma switch.. It can also act as a
Zigbee router to expand your Zigbee mesh network. Only compatible with motors
with mechanical limit switch detection
Not compatible with motors with electronic limit switch detection
Installation [→Figure A]
Thanks to its compact size, this product can be installed in a junction box or
behind the wall switch controlling the motorized product.
In detail [→Figure B]
Each terminal can accept a cable of 2.5 mm² maximum, stripped of 8 mm.
Wiring with switch [→Figure C]
- Switch off the power supply.
- Disassemble the wired wall switch controlling the motorized product to be connected.
- Wire IZYMO MOTOR RECEIVER Zigbee according to the diagram.
- Reassemble the wired wall switch.
- Turn the power back on.
Wiring without switch
- Switch off the power supply.
- Wire IZYMO MOTOR RECEIVER Zigbee according to the diagram.
- Turn the power back on.
Auto-detection of switch type
After turning the power supply on, do a single push on the wired wall switch
to bring the motorized product half-height. IZYMO MOTOR RECEIVER Zigbee has an
auto-detection system to automatically detect the type of wired wall switch
(toggle switch or push-button) wired at the input.
Note: To perform a new auto-detection, IZYMO MOTOR RECEIVER Zigbee must
be manually reset (see 8. Reset to original configuration).
Calibration [→Figure E]
IZYMO MOTOR RECEIVER Zigbee must be power supplied.
- Do 5 short presses on the Press button. Note: The LED blinks green, meaning the calibration has been well started and the motorized product moves back and forth several times..
Pairing to TaHoma switch
IZYMO LIGHTING RECEIVER Zigbee must be plugged in and powered up.
- It enters pairing mode for 15 minutes after being powered up. The LED flashes orange. If the product is already paired, return to the original configuration (see 8. Return to original configuration).
- On the Tahoma application home page, select + , choose Windows and Sun protection, then Somfy, and then select the type of motorized product to be controlled.
- Follow the instructions in the application to complete the configurations.
Tips: It is recommended to perform the setup of the receiver within 15 feet (4.5 meters) of a Zigbee Router.
Unpairing
IZYMO MOTOR RECEIVER Zigbee must be power supplied and paired.
- On the Tahoma application home page, select the receiver to be unpaired.
- Follow the instructions in the application to remove the receiver from Tahoma.
Reset to original
configuration [→Figure G] IZYMO MOTOR RECEIVER Zigbee must be power supplied.
- Press more than 5 seconds on the IZYMO MOTOR RECEIVER Zigbee Press button: the LED blinks orange.
- Press once again the Press button (short press) to confirm the reset. If the reset is correct, the LED blinks alternatively in red and green and stays green. Start again if necessary.
- IZYMO MOTOR RECEIVER Zigbee has now its original settings.
Tips : It is recommended to perform the reset of the receiver within 15 feet (4.5 meters) of a Zigbee Router
Note: To remove the receiver from Tahoma, see 7.Unpairing.
Technical data
- Power supply 110 V – 230 V AC on 50 Hz/60 Hz
- Switching capabilities 110 V – 230 V AC – 3A
- Consumption < 1 W
- Maximum motor power List of compatible motors is available onwww.somfy.com.
- 280W Max – 60 Nm Max (230V)
- 140W Max – 30 Nm Max (110V)
- Integrated zero crossing
- RF protocol Zigbee 3.0
- Radiofrequency range 2.4 GHz
- RF power Max +10 dBm
- Range up to 40 m indoors
- Protection rating IP20
- Operational temperature -4°F to 122°F (-20°C to 50°C)
- Device ID Type Window Covering Device (0x0202)
FCC
FCC warning statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
-
This device may not cause harmful interference, and
-
This device must accept any interference received, including interference that may cause undesired operation.
-
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions to satisfy RF exposure compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
We care about our environment. Do not dispose of the appliance with usual
household waste. Give it to an approved collection point for recycling.
Nous nous soucions de notre environment.
MORE INFORMATION
SOMFY ACTIVITIES SA
- 50 avenue du Nouveau Monde
- 74300 Cluses FRANCE: www.somfy.com
FAQ
- Q: Can this product be used outdoors?
- A: No, this product should not be used outdoors according to safety instructions.
- Q: What should I do if the LED is still on during operation?
- A: Cut the power supply before any operation and do not perform any modifications if the LED is still on