signify LIGHTOLIER IS M_GRW Downlighting Instruction Manual

: July 31, 2024
: signify

Table of Contents

signify LIGHTOLIER IS M_GRW Downlighting
Product Usage Instructions
Cutout Dimensions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

signify LIGHTOLIER IS M_GRW Downlighting

Specifications

Model: ModuLyte 4in, 6in & 8in
Product Code: IS M_GRW 442296472141
Compatibility: Can be installed in commercial environments
Compliance: FCC Part 15 Class A digital service

Product Usage Instructions

Step 1: Make the Ceiling Cutout
Note: Confirm the dimensions needed for your installation based on the Cutout Dimensions section in the manual. Ensure there are no obstructions in the ceiling.
Step 2: Install the Goofring
Take the goofring with the inner diameter side facing down and pass it over the luminaire. Bend the trims before passing the goofring through.
Step 3: Position the Luminaire and Goofring
Ensure that the luminaire and goofring faces are correctly aligned.
Step 4: Attach the Driver Box
Pass the driver box through the ceiling hole and retain the cord to attach it to the luminaire.

FAQ

Q: Can this product be installed in residential areas?
- A: This product is designed for commercial environments. Installing it in a residential area may cause harmful interference to radio communications.
Q: What are the standard cutout dimensions for the different sizes?
- A: The standard cutout dimensions are as follows:
- 4in Round : 4.87” (123.698mm) up to 5.75” (146.05 mm)
- 6in Round: 6.37” (161.798mm) up to 7.25” (184.15 mm)
- 8in Round: 8.37” (212.598mm) up to 9.25” (234.95 mm)

Downlighting

IS M_GRW 442296472141
ModuLyte 4in, 6in & 8in

CAUTION: THE INSTALLATION AND SERVICING OF THIS PRODUCT MUST BE PERFORMED BY A QUALIFIED ELECTRICIAN OR SERVICE PERSONNEL

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital service, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, many cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAN ICES-005 (A) / NMB-005 (A)
Read and understand these instructions before installing luminaire (fixture)
This luminaire is intended for installation in accordance with the National Electrical Code and local regulations. To assure full compliance with local codes and regulations, check with your local electrical inspector before installation.

WARNING – To prevent electrical shock, turn off electricity at fuse box before proceeding. Allow fixture to cool before handling.

Retain these instructions for maintenance reference

ModuLyte accepts Light Engines:
M4RDL, M6RDL & M8RDL

Caution (RISK OF FIRE)
Use only with ModuLyte LED light engines and reflector.

WARNING – Make sure that the power supply is disconnected before installation.

Cutout Dimensions

4in
Round: Standard cutout 4.87’’ (123.698mm) up to 5.75” (146.05 mm)
6in
Round: Standard cutout 6.37” (161.798mm) up to 7.25” (184.15 mm)
8in
Round: Standard cutout 8.37” (212.598mm) up to 9.25” (234.95 mm)

Parts

Step 1
Make the ceiling cutout.
Note: Confirm the dimensions needed for your installation in the “Cutout Dimensions” section on page 1 and ensure that there is nothing in the ceiling to obstruct the installation (Figure 1).

Step 3
Be sure to settle the luminaire and goofring faces correctly (Figure 3).

Step 5
Insert the luminaire and goofring to the ceiling. Bend the springs of the luminaire and insert it on the ceiling hole (Figure 5).
WARNING – Watch out for falling parts and make sure the springs open back to position once the luminaire is inserted to prevent any risk of injury.

Step 2
Take the goofring, with the inner diameter side facing down, and pass it over the luminaire (Figure 2).
Note: Bend the trims before the goofring is passing through.

Step 4
Pass the driver box through the ceiling hole and retain the cord to attach to luminaire (Figure 4).

© 2024 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify.